2003 SUBARU OUTBACK audio

5
Audio5-19
–
CONTINUED –
FM1 FM2 AM
The display indicates which one is currently selected.
Stereo indicator
The stereo indicator “ST” will come on when an FM stereo broadcast
is received. Weather band button (WB)
Push the “WB” button
5 when the radio is off to turn on the radio in
the weather band.
Press the “WB” button when the radio is on to select the weather
band. Manual tuning (TUNE)
n Manual tuning for AM and FM waveband
Push the tuning button 7 marked “ ” to increase the tuning frequen-
cy and press the tuning button marked “ ” to decrease it.
Each time the button is pressed, the frequency changes 10 KHz in the AM waveband and 0.2 MHz in the FM waveband.
Constant pressure on the button causes a continuous change in the
frequency. n Manual tuning for weather band
When weather band mode is selected, press the tuning button 7
marked “ ” to change the WB channel up and press the tuning but-
ton marked “ ” to change the WB channel down. Each time the but-
ton is pressed, the WB channel changes to the next channel.
Constant pressure on the button causes a continuous change in thechannel. Automatic tuning (SCAN)
Press the “SCAN” button
8 to change the radio to the SCAN mode. In
this mode, the radio scans through the radio band until a station is
found. The radio will stop at the station for five seconds while display-
ing the frequency, after which scanning will continue until the entire

5
Audio5-21
–
CONTINUED –
Built-in CD changer operation
HB5064CB
9 Eject button
Q Disc slot
W CD (CD player selection) button
E Repeat button R
Random button
T LOAD button
Y Disc select buttons
U Track selection buttons
I SCAN button
NOTE
Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the playermight shut off.
How to insert a CD(s)
n Inserting a CD
1. Press “LOAD” button E. If the magazine in the player has an idle
position where you can insert a disc, the “DISC” indicator associated
with the idle position will blink.
If no indicator blinks, it means that there is no idle position in the mag-azine.
2. As soon as the “DISC” indicator begins to blink, the “IN” will ap-

5
Audio5-23
–
CONTINUED –
period of 15 seconds. If a disc is successfully loaded during this peri- od, the
“DISC” indicator will stop blinking and will steadily light.
3. When the loading of a disc is complete, the next “DISC” indicator
will blink. Then repeat Step 2.
4. When the magazine is filled with discs by repeating Steps 2 and 3,
the player will start playback of the discs, beginning with the one in-
serted first.
If you fail to insert any disc during each 15-second interval, the full
disc loading mode will be canceled, and the player will start playback
of the disc inserted first. How to play back a CD or make a pause
n When there is no CD inserted:
Insert a CD by referring to “How to Insert a CD(s) ”.
When a CD is loaded, the player will start playback of the CD, begin-
ning with the first number. n When there are CDs loaded:
Press a desired one of the “DISC SELECT ” buttons
Y the “DISC” indi-
cator of which steadily lights up. The player will then start playback of
the selected CD, beginning with the first number. To select a song from its beginning
n Forward direction
Briefly press the “ ” button U to skip to the beginning of the next
track. Each time the button is pressed, the indicated track number will
increase. n Backward direction
Briefly press the “
 ” button U to skip to the beginning of the current
track. Each time the button is pressed, the indicated truck number will
decrease. Fast forwarding and fast reverse
n Fast forwarding
Press the “
 ” button U continuously for more than 0.5 second to fast
forward the disc.

5
Audio5-25
–
CONTINUED –
n
Ejecting all discs from the player (All disc ejection mode)
1. If you continue to press the “EJECT” button 9, the player will pro-
duce beep sound and will enter the all disc ejection mode.
2. Remove the disc that has been ejected. The other discs loaded
will then be ejected one after another. If you do not remove the discthat has been ejected, the “All disc ejection mode ” will be canceled.
NOTE
Avoid driving the vehicle with a CD sticking out, because vibra- tion might make it fall out.
OnStar  system operation (models with OnStar  sys-
tem) When the OnStar system operates and a call is initiated, the message
“CALL” will be shown on the display, and the speakers will automatically
switch over to the incoming voice signal. NOTE A call will not be suspended even if the ignition key is turned to the
Off position. In such a case, however, the audio system will turn offwhen the call is ended.

5-26McIntosh audio set (if equipped) The audio set will operate only when the ignition switch is in the
“ACC” or
“ON” positions.
CAUTION
The power amplifier for this audio set is mounted under the front
passenger’ s seat. The amplifier will become hot if the audio con-
tinues to operate.
Never touch the amplifier. Doing so could cause burns.
Radio operation
HB5063BB
1 FM/AM selection button
2 Weather band button
3 Tuning/FF FB dial
4 SCAN button
5 Preset buttons
6 Fader/Balance control button 7
Power switch, Volume
control, Bass/Treble control
and Fader/Balance control dial
8 Bass/Treble sound controlbutton

5
Audio5-27
–
CONTINUED –

Power switch and volume/bass/treble/fader/balance control (ON/VOL)
The dial 1 is used for both power (ON/OFF) and volume control. The
radio is turned ON and OFF by pushing the dial and the volume is
controlled by turning the dial.
This dial is used for bass/treble controls when the “BASS/TREB” but-
ton 8 is in the depressed position. It is also used for fader/balance
controls when the “FAD/BAL” button 6 is in the depressed position.
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASSBass controlFor less bassFor more bass
TREBTreble controlFor less trebleFor more treble
FA DFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume
nTone control
The volume control dial 7 normally function as volume control. The
dial become a control for Bass or Treble when you select the ap-
propriate tone control mode.
Choose desired level for each mode by turning the volume control
dial. The control function returns to volume control mode after about 5seconds.

5
Audio5-29
–
CONTINUED –

FM/AM selection button
Press the “FM/AM” selection button 1 to choose either FM or AM
broadcasts. The display will show FM or AM accordingly. Use the tuning dial to select the station to which you wish to listen. Manual tuning
Turn the tuning dial 3 outer tuner to increase or decrease the recep-
tion frequency in individual steps.
FM band: 0.2 MHz steps AM band: 10 kHz steps
Seek tuning (SEEK)
If the Tuning dial 3 outer tuner is turned for longer than half of a se-
cond, the radio will begin to automatically search for receivable fre-
quencies and will stop at the first one found. This function may not be
available, however, when radio signals are weak. In such a situation,
perform manual tuning to select the desired station. Scan tuning (SCAN)
Press the “SCAN” button
4 to change the radio to the SCAN mode. In
this mode, the radio scans through the radio band until a station is
found. The radio will stop at the station for five seconds while display-
ing the frequency, after which scanning will continue until the entireband has been scanned.
Turn the tuning dial 3 inner tuner again to cancel the SCAN mode
and to stop on any displayed frequency.
Scan tuning may not function properly if the station reception is weak-
ened by distance from the station or proximity to tall buildings andhills. Preset tuning
Press any one of the preset buttons 5 to select the corresponding,
previously-registered radio station. The LED at the top of that button
will turn on. n Manual preset
Use the tuning dial 3 to select the radio station which you wish to
register.

5
Audio5-31
–
CONTINUED –
Built-in CD changer operation
HB5063CB
9 DISC IN indicator light
Q Disc slot
W Eject button
E LOAD button R
Repeat button
T FF· FB dial
Y Disc button
U Disc select button
NOTE Single CDs (i.e., 8-cm/3-inch CDs) are not supported, and if in-
serted, they will be immediately ejected. Make sure to always insert a disc with the label side up. If a disc
is inserted with the label side down, it might be ejected or the playermight shut off. If a disc is inserted during a radio broadcast, the disc will inter-
rupt the broadcast. After the last song finishes, the disc will automatically return to
track 1 (the first song on the disc) and will automatically play back.