2003 SUBARU OUTBACK lock

1-6
Reclining the seatback
n Manual type
HB1072BA
Pull the reclining lever up and adjust the seatback to the desired posi-
tion. Then release the lever and make sure the seat is securely locked
into place.
The seatback placed in a reclined position can spring back upward
with force when released. When operating the reclining lever to return
the seatback, hold it lightly so that it may be raised back gradually. nPower seat (if equipped)
HB1084BA
To adjust the angle of the seatback, move the control switch.

1
Seat, seatbelt and SRS airbags1-13
–
CONTINUED –

Folding down the seatback
HB1095BA
HB1094BA
1. Lower the headrests.
2. Unlock the seatback by pulling the release knob and then fold theseatback down. Folding down the seat cushion and seatback
1. Move the front seat forward.
2. Close the rear passengers ’ cup holder and ashtray.
3. Remove the headrests (if so equipped).
Window-side seating positions: Pull the headrest up while pressing
the release button located on the backside of the seatback.Center seating position: Pull the headrest up while pressing the re-
lease button located on the top of the seatback.
HB1099CB
HB1096BB

1-144. Store the seatbelts in the seatbelt pockets to prevent them from fal- ling below the cushion.
HB1074BB
5. Raise the seat cushion by pulling up the tab.
Make certain that the rear passenger
’s cup holder is fully retracted
before raising the seat cushion.
HB1097BA
6. Unlock the seatback by pulling the release knob and fold the seat-
back down. Confirm that the pin located at the bottom of the seat
cushion is inserted into the slot at the top of the seatback.

1
Seat, seatbelt and SRS airbags1-15
–
CONTINUED –
HB1027BA
7. Install the headrests (if so equipped) onto the backside of the seat- back (window-side positions only).
HB1098BA
To return the rear seat to its original position, raise the seatback and seat
cushion until they lock into place and make sure that they are securelylocked.
Make sure that the rear seatbelts are not under the seat cushion or seat-back.
Place the headrests (if so equipped) back in their normal position.

1-18Expectant mothers also need to use the seatbelts. They should con-
sult their doctor for specific recommendations. The lap belt should be
worn securely and as low as possible over the hips, not over thewaist.
Emergency Locking Retractor (ELR)
The driver ’s seatbelt has an Emergency Locking Retractor (ELR).
The emergency locking retractor allows normal body movement but the
retractor locks automatically during a sudden stop, impact or if you pull
the belt very quickly out of the retractor. Automatic/Emergency Locking Retractor (A/ELR)
Each passenger ’s seatbelt has an Automatic/Emergency Locking Re-
tractor (A/ELR). The Automatic/Emergency Locking Retractor normally
functions as an Emergency Locking Retractor (ELR). The A/ELR has an
additional locking mode “Automatic Locking Retractor (ALR) mode ” in-
tended to secure a child restraint system. When the seatbelt is once
drawn out completely and is then retracted even slightly, the retractorlocks the seatbelt in that position and the seatbelt cannot be extended.
As the belt is rewinding, clicks will be heard which indicate the retractor
functions as ALR. When the seatbelt is retracted fully, ALR mode is re-leased.
When securing a child restraint system on the passengers ’ seats, the
seatbelt must be changed over to the Automatic Locking Retractor (ALR) mode.
When the child restraint system is removed, make sure that the retractor
is restored to the Emergency Locking Retractor (ELR) function by allow-
ing the seatbelt to retract fully.
For instructions on how to convert the retractor to the ALR mode and re-
store it to the ELR mode, see the “Child restraint systems ” section in this
chapter. Seatbelt warning light and chime
Your vehicle is equipped with a seatbelt warning device at the driver ’s
seat.

1
Seat, seatbelt and SRS airbags1-21
–
CONTINUED –
2. Sit well back in the seat.
3. Pick up the tongue plate and pull the belt out slowly. Do not let it
get twisted. If the belt stops before reaching the buckle, return the
belt slightly and pull it out more slowly. If the belt still cannot be
unlocked, let the belt retract slightly after giving it a strong pull, thenpull it out slowly again.
4. Insert the tongue plate into the buckle until you hear a click.
5. To make the lap part tight, pull up on the shoulder belt. And placethe lap belt as low as possible on your hips, not on your waist. n
Adjusting the front seat shoulder belt anchor height
WARNING
When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the
seatbelt anchor to a lower position. Placing the shoulder beltover the neck may result in neck injury during sudden braking orin a collision.
HB1029BB
The shoulder belt anchor height should be adjusted to the position
best suited for you. To lower the anchor height, push the release but-
ton and slide the anchor down. To raise the anchor height, slide the
anchor up. Pull down on the anchor to make sure that it is locked inplace.

1-22Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck. n
Unfastening the seatbelt
HB0303
Push
Push the button on the buckle.
Before closing the door, make sure that the belts are retracted prop-
erly to avoid catching the belt webbing in the door. Rear seatbelts (except rear center seatbelt on wagon)
OM-H0044OM-H0043
1. Sit well back in the seat.
2. Pick up the tongue plate and pull the belt out slowly. Do not let it
get twisted. If the belt stops before reaching the buckle, return the
belt slightly and pull it out more slowly. If the belt still cannot be
unlocked, let the belt retract slightly after giving a strong pull on it,

1
Seat, seatbelt and SRS airbags1-25
–
CONTINUED –
HB1033BA
2. After confirming that the webbing is not twisted, insert the connec- tor (tongue) attached at the webbing end into the buckle on the right-
hand side until a click is heard. If the belt stops before reaching the
buckle, return the belt slightly and pull it out more slowly. If the belt
still cannot be unlocked, let the belt retract slightly after giving it a
strong pull, then pull it out slowly again.
HB1034BA
3. Insert the center seatbelt tongue plate in the center seatbelt buckle
marked “CENTER” on the left-hand side until it clicks. To make the lap
part tight, pull up on the shoulder belt. And place the lap belt as lowas possible on your hips, not on your waist.