2003 SUBARU OUTBACK clock

5
Audio5-17
–
CONTINUED –
This dial is used for bass/middle/treble controls when the
“AUDIO”
button 2 is in the depressed position. It is also used for fader/balance
controls when the “BAL” button 3 is in the depressed position.
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASSBass controlFor less bassFor more bass
MIDDLEMiddle note controlFor less middle noteFor more middle note
TREBLETreble controlFor less trebleFor more treble
FADERFader controlTo increase rear speaker volume and decrease
front speaker volumeTo increase front speaker volume and decrease
rear speaker volume
BALANCEBalance controlTo increase left speaker volume and decrease
right speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLUMEVolume controlFor less volumeFor more volume
nTone control
The volume control dial 1 normally function as volume control. The
dial become a control for Bass, Middle note or Treble when you select
the appropriate tone control mode.
Choose desired level for each mode by turning the volume control
dial. The control function returns to volume control mode after about 5seconds.
To change control modes: Each brief press of the “AUDIO” button
2 changes control modes in the following sequence starting from
bass control mode. (When the radio is first turned on, the control
mode is in the volume control.)

5
Audio5-27
–
CONTINUED –

Power switch and volume/bass/treble/fader/balance control (ON/VOL)
The dial 1 is used for both power (ON/OFF) and volume control. The
radio is turned ON and OFF by pushing the dial and the volume is
controlled by turning the dial.
This dial is used for bass/treble controls when the “BASS/TREB” but-
ton 8 is in the depressed position. It is also used for fader/balance
controls when the “FAD/BAL” button 6 is in the depressed position.
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASSBass controlFor less bassFor more bass
TREBTreble controlFor less trebleFor more treble
FA DFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume
nTone control
The volume control dial 7 normally function as volume control. The
dial become a control for Bass or Treble when you select the ap-
propriate tone control mode.
Choose desired level for each mode by turning the volume control
dial. The control function returns to volume control mode after about 5seconds.

5-34
Selecting a desired track (TRACK)
HB5065BA
nSkipping forward
Turn the FF ·FB dial T clockwise and release it immediately to skip to
the beginning of the next track. Each time the knob is turned and re-
leased, the indicated track number will increase. n Skipping backward
Turn the FF ·FB dial
T counterclockwise and release it immediately to
skip to the beginning of the current track. If you continue to turn and
release the knob, the indicated truck number will decrease. n Fast forwarding
Turn the FF ·FB dial T clockwise and hold it continuously for more than
0.5 second to fast forward the disc.
Release the knob to stop fast forwarding. n Fast reversing
Turn the FF ·FB dial T counterclockwise and hold it continuously for
more than 0.5 second to fast reverse the disc.
Release the knob to stop fast reverse. Repeat playback
Press the “RPT” button R while a song is playing to play the song
repeatedly. The “RPT” indicator will come on and the song will be
played continuously. To cancel the repeat mode, press the button
again. Then the “RPT” indicator goes out, and normal playback mode
is restored.
❚: Skipping forward
❚ : Skipping backward
: Fast forwarding
: Fast reversing

6-6

Glove box
HS0090
Unlock
Lock
To open the glove box, pull the handle. To close it, push the lid firmly
upward.
To lock the glove box, insert the key and turn it clockwise. Center console
HB6022BA
To open the lid, pull up the lock release.
If the console lid is fully opened when a large cup is put in the rear pas-
senger’ s cup holder, the lid may hit the cup and beverage may be
spilled.

7-6
HB7030BB
2. Remove the fuel filler cap by turning it slowly counterclockwise.
3. Stop filling the tank after the fuel filler pump automatically clicks off.
Do not add any more fuel.
4. Put the cap back on, turn it clockwise until you hear a clicking
noise. Be certain not to catch the tether under the cap while tighten-ing.
5. Close the fuel filler lid completely.
If you spill any fuel on the painted surface, rinse it off immediately.
Otherwise, the painted surface could be damaged. NOTE
HG3016AA
You will see the “FUEL DOOR p” sign in the combination
meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.

9-6
5. Take out the spare tire, jack, and wheel nut wrench.
HB6008BCHB9003BB
HS0252
Temporary spare tire
HBF015CB
Jack handle
Jack
Spare tireHB8004BD
The spare tire is stored under the floor of the trunk or cargo area.
To remove the spare tire, proceed as follows:Sedan: Remove the floor cover from the trunk. Remove the storage tray.
Turn the attaching bolt counterclockwise, then take the spare tire out.Station wagon: Open the lid and hang the hook provided on the under-

9
In case of emergency9-7
–
CONTINUED –
side of the lid on the rear edge of the roof to keep the lid open.
Remove the storage tray. Turn the attaching bolt counterclockwise, then
take spare tire out.
If the spare tire provided in your vehicle is a temporary spare tire, care-
fully read the section
“Temporary spare tire ” in this chapter and strictly
follow the instructions.
HB7008CD
HB9001BB
The jack is stored on the left side of the trunk or cargo area.
To take out the jack:
Remove the cover, turn the jackscrew counterclockwise to loosen it, then
remove the jack.
HB9041BA
HB9040BA
If the jackscrew is too tight to be loosened by hand, loosen it using a
screwdriver or the jack handle.

9-10
HG0104
OM-H0172
12. Put on the spare tire. Replace the wheel nuts. Tighten them by hand.
13. Turn the jack handle counterclockwise to lower the vehicle.
14. Use the wheel nut wrench to securely tighten the wheel nuts to the
specified torque, following the tightening order in the illustration.
OM-H0377
The torque for tightening the nuts is 58 to 72 ft-lb (78 to 98 N-m, 8 to 10
kg-m). This torque is equivalent to applying about 88 to 110 lbs (40 to 50
kg) at the top of the wheel nut wrench. Never use your foot on the wheel
nut wrench or a pipe extension on the wrench because you may exceed
the specified torque. Have the wheel nut torque checked at the nearest
automotive service facility.
15. Store the flat tire in the spare tire compartment.