2003 SUBARU OUTBACK In Case of Emergency

9
In case of emergency9-7
–
CONTINUED –
side of the lid on the rear edge of the roof to keep the lid open.
Remove the storage tray. Turn the attaching bolt counterclockwise, then
take spare tire out.
If the spare tire provided in your vehicle is a temporary spare tire, care-
fully read the section
“Temporary spare tire ” in this chapter and strictly
follow the instructions.
HB7008CD
HB9001BB
The jack is stored on the left side of the trunk or cargo area.
To take out the jack:
Remove the cover, turn the jackscrew counterclockwise to loosen it, then
remove the jack.
HB9041BA
HB9040BA
If the jackscrew is too tight to be loosened by hand, loosen it using a
screwdriver or the jack handle.

9
In case of emergency9-9
–
CONTINUED –
to by arrow marks on the underside of the side sill skirt. Place the jack
under the front or rear jack-up point closest to flat tire.
HS9023BA
9. Insert the jack handle into the jackscrew, and turn the handle until the
tire clears the ground. Do not raise the vehicle higher than necessary.
OM-H2263
10. Remove the wheel nuts and the flat tire.
11. Before putting the spare tire on, clean the mounting surface of thewheel and hub with a cloth.

9
In case of emergency9-11
–
CONTINUED –
HS0153
Flat tire Attaching bolt
Spacer
When storing a conventional tire, put the spacer upside down and tight-
en the attaching bolt firmly.
Also store the jack and wheel nut wrench in their storage locations.
HB9041CA
HB9040CA
After placing the jack in its storage location, turn the jackscrew clock-
wise by hand until it becomes too hard to turn. Then, tighten it by an
additional 1/4 – 1/3 of a turn using a screwdriver or the jack handle. Un-
less the jack is properly secured, it may rattle while the vehicle is mov-ing.

9
In case of emergency9-13
–
CONTINUED –

How to jump start
1. Make sure the booster battery is 12 volts and the negative terminal
is grounded.
2. If the booster battery is in another vehicle, do not let the two ve-hicles touch.
3. Turn off all unnecessary lights and accessories.
4. Connect the jumper cables exactly in the sequence illustrated.
HB8007BC

9
In case of emergency9-15
–
CONTINUED –
Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has fully cooled down. When the engine is hot,the coolant is under pressure. Removing the cap while the engineis still hot could release a spray of boiling hot coolant, which
could burn you very seriously.
If the engine overheats, safely pull off the road and stop the vehicle in asafe place. If steam is coming from the engine compartment
Turn the engine off and get everyone away from the vehicle until itcools down. If no steam is coming from the engine compartment
1. Keep the engine running at idling speed.
2. Open the hood to ventilate the engine compartment.
Confirm that the cooling fan is turning. If the fan is not turning, im-
mediately turn the engine off and contact your authorized dealer for
repair.
3. After the engine coolant temperature has dropped, turn off the en-gine.
If the temperature gauge stays at the overheated zone, turn the en-
gine off.
4. After the engine has fully cooled down, check the coolant level in
the reserve tank.If the coolant level is below the “MIN” mark, add coolant up to the
“MAX” mark.
5. If there is no coolant in the reserve tank, add coolant to the reserve
tank. Then remove the radiator cap and fill the radiator with coolant.
If you remove the radiator cap from a hot radiator, first wrap a thick
cloth around the radiator cap, then turn the cap counterclockwise
slowly without pressing down until it stops. Release the pressure from

9
In case of emergency9-17
–
CONTINUED –
HB8012BB HB9051BB
HB9048BB
Towing and tie-down hook
HB8013BB

9
In case of emergency9-19
–
CONTINUED –
For OUTBACK models:
HB9042BA
HB9045BB
1. Squeeze the sides of portion A and pull the towing hook cover to-
ward you.
HB9043BA
HB9021CB
2. Press portion B and simultaneously pull the towing hook cover to-
ward you.

9
In case of emergency9-21
–
CONTINUED –
For OUTBACK models:
HB9044CB
1. IInsert the projection
C into the hole D.
HB9030CB
2. Push at the portion E.