2003 SUBARU IMPREZA WRX maintenance

Maintenance and service
11-4
Always be very careful to avoid injury when
working on the vehicle. Remember that some of the materials in the vehicle may be hazard-
ous if improperly used or handled, for exam-ple, battery acid. Your vehicle should only be serviced by per-
sons fully competent to do so. Serious per-sonal injury may result to persons not experi-enced in servicing vehicles. Always use the proper tools and make cer-
tain that they are well maintained. Never get under the vehicle supported only
by a jack. Always use a safety stands to sup-port the vehicle. Never keep the engine running in a poorly
ventilated area, such as a garage or other
closed areas. Do not smoke or allow open flames around
the fuel or battery. This will cause a fire. Because the fuel system is under pressure,
replacement of the fuel filter should be per-
formed only by your SUBARU dealer. Wear adequate eye protection to guard
against getting oil or fluids in your eyes. If something does get in your eyes, thoroughly
wash them out with clean water. Do not tamper with the wiring of the SRS airbag system or seatbelt pretensioner sys-tem, or attempt to take its connectors apart,as that may activate the system or it can ren-der it inoperative. The wiring and connectorsof these systems are yellow for easy identifi-cation. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pretensionerneeds service, consult your nearest SUBARU
dealer.
Before checking or servicing in the
engine compartment
Always stop the engine and set the parking
brake firmly to prevent the vehicle from mov- ing. Always let the engine cool down. Engine
parts become very hot when the engine is run-
ning and remain hot for some time after theengine is stopped. Do not spill engine oil, engine coolant, brake
fluid or any other fluid on hot engine compo-nents. This may cause a fire. Always remove the key from the ignition
switch. When the ignition switch is in the
“ON” position, the cooling fan may operate

Maintenance and service
11-5
– CONTINUED –
suddenly even when the engine is stopped. When you do checking or servicing in the engine compartment whilethe engine is running
A running engine can be dangerous. Keep your fingers, hands, clothing, hair and toolsaway from the cooling fan, belts and any other
moving engine parts. Removing rings,watches and ties is advisable. Engine hood
To open the hood:
1. Pull the hood release knob under the instrument panel.

Maintenance and service
11-6
2. Release the secondary hood release located
under the front grille by moving the lever toward theleft.Lift up the hood, release the hood prop from its
retainer and put the end of the hood prop into theslot in the hood.
To close the hood: All models except WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 6 in.
(15 cm) from the closed position and let it drop.

Maintenance and service
11-7
– CONTINUED –
WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 12 in.
(30 cm) from the closed position and let it drop.
After closing the hood, be sure the hood is securelylocked.
If this does not close the hood, release it from a
slightly higher position. Do not push the hood forci-
bly to close it. It could deform the metal.
WARNING
Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block
your view, which may cause an accident and
serious bodily injury.

Maintenance and service
11-8
Engine compartment overview 2.5 liter model
1) Manual transmission oil level gauge
(MT) (page 11-25) or Differential
gear oil level gauge (AT) (page 11-29)
2) Air cleaner element (page 11-20)
3) Clutch fluid reservoir (page 11-35)
4) Automatic transmission fluid level gauge (page 11-27)
5) Brake fluid reservoir (page 11-34)
6) Windshield washer tank (page
11-50)
7) Fuse box (page 11-56)
8) Battery (page 11-54)
9) Engine oil filler cap (page 11-10)
10) Engine coolant reservoir (page 11-16)
11) Radiator cap (page 11-16)
12) Engine oil level gauge (page 11-10)
13) Power steering fluid reservoir (page 11-32)

Maintenance and service
11-9
– CONTINUED –
2.0 liter (Turbo) model
1) Manual transmission oil level
gauge (MT) (page 11-25) or
Differential gear oil level gauge
(AT) (page 11-29)
2) Air cleaner element (page 11-20)
3) Clutch fluid reservoir (page
11-35)
4) Automatic transmission fluid level gauge (page 11-27)
5) Brake fluid reservoir (page
11-34)
6) Windshield washer tank (page
11-50)
7) Fuse box (page 11-56)
8) Battery (page 11-54)
9) Engine oil filler cap (page 11-10)
10) Engine coolant reservoir (page
11-16)
11) Engine oil level gauge (page 11-10)
12) Radiator cap (page 11-16)
13) Power steering fluid reservoir (page 11-32)

Maintenance and service
11-10
Engine oil Checking the oil level
Check the engine oil level at each fuel stop.
1. Park the vehicle on a level surface and stop theengine.
2. Pull out the dipstick, wipe it clean, and insert it again.
3. Be sure the dipstick is correctly inserted until it
stops with the graphic symbol i on its top ap-
pearing as shown in the illustration.
1) Notch
2) Upper level 3) Lower level
4) Front of vehicle
4. Pull out the dipstick again and check the oil level on it. If it is below the lower level, add oil to bring thelevel up to the upper level.
CAUTION
Use only engine oil with the recommended
grade and viscosity. Be careful not to spill engine oil when ad-
ding it. If oil touches the exhaust pipe, it may
cause a bad smell, smoke, and/or a fire.

Maintenance and service
11-11
– CONTINUED –
If you check the oil level just after stopping the en-
gine, wait a few minutes for the oil to drain back into
the oil pan before checking the level.
Just after driving or while the engine is warm, the
engine oil level reading may be in a range betweenthe upper level and the notch mark. This is caused
by thermal expansion of the engine oil.
To prevent overfilling the engine oil, do not add any
additional oil above the upper level when the engineis cold. Changing the oil and oil filter
Change the oil and oil filter according to the mainte-
nance schedule in the “Warranty and Maintenance
Booklet”.
The engine oil and oil filter must be changed more
frequently than listed in the maintenance schedule
when driving on dusty roads, when short trips are
frequently made, or when driving in extremely cold
whether.
1. Warm up the engine by letting the engine idle for
about 10 minutes to ease draining the engine oil.
2. Park the vehicle on a level surface and stop theengine.
3. Remove the oil filler cap.
1) Drain plug
4. Drain out the engine oil by removing the drain
plug while the engine is still warm. The used oil
should be drained into an appropriate container and
disposed of properly.
WARNING
Be careful not to burn yourself with hot en- gine oil.
5. Wipe the seating surface of the drain plug with a
clean cloth and tighten it securely with a new seal-