2003 SUBARU IMPREZA service

Maintenance and service
11-64
3. Remove the bulb from the headlight assembly.
4. Install the new bulb.
5. Install the bulb holder in the headlight assembly
by turning it clockwise until it locks.
6. Reconnect the electrical connector.
Front turn signal light and parking light
1) Front turn signal light
2) Parking light

Maintenance and service
11-65
– CONTINUED –
Front turn signal light bulbs
1. Remove the bulb socket from the headlight as-
sembly by turning it counterclockwise.
2. Pull the bulb out of the socket. Install a new bulb.
3. Set the bulb socket into the headlight assembly
and turn it clockwise until it locks.
Parking light bulbs
The headlight assembly must be removed before
the parking light bulbs can be replaced. When the
headlight assembly has been removed and then re-
installed, it may become necessary to make a head-
light aiming adjustment. It may be difficult to replace
the bulbs. Have your SUBARU dealer replace the bulbs if necessary.
: Clip : Hook

Maintenance and service
11-66
1. Remove the front grille. Use a screwdriver to de-
tach the four clips at the top and the two hooks on
each side.2. Loosen three clips to remove the grille side cover.

Maintenance and service
11-67
– CONTINUED –
3. Remove three bolts and disconnect connectors, and then detach headlight assembly.
4. Remove the bulb socket from the headlight as-
sembly by turning it counterclockwise.
5. Pull the bulb out of the socket. Install a new bulb.
6. Set the bulb socket into the headlight assembly
and turn it clockwise until it locks.

Maintenance and service
11-68
Front fog light (if equipped)
1. Remove the front fog light assembly by removing
the three bolts.
2. Disconnect the connector.
3. Remove the front fog light case cap by turning it
counterclockwise.

Maintenance and service
11-69
– CONTINUED –
1) Spring
2) Connector
4. Disconnect the connector behind the case cap.
5. Release the retainer spring.
6. Replace the bulb with a new one. Then reconnect
the connectors and reinstall the removed parts in
the reverse order of removal.
CAUTION
Halogen fog light bulbs become very hot while
in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface develop into hotspots, causing the bulb to break. If there arefinger prints or grease on the bulb surface,
wipe them away with soft cloth moistenedwith alcohol.
Front side marker light
1. Remove the front side marker light assembly by

Maintenance and service
11-70
prying the edge of the lens with a regular screwdriv-
er. At this time, use a cloth to protect the body from
being damaged by the screwdriver.
2. Remove the bulb holder from the front side mark-
er light assembly by turning it counterclockwise.
3. Pull the bulb out of the socket. Install a new bulb.
4. Set the bulb holder into the front side marker light
assembly and turn it clockwise until it locks.
5. Reinstall the front side marker light assembly
onto the side of the front fender. Rear combination lights
Sedan1. Remove the clip from the rear trunk trim with a
regular screwdriver.
1) Backup light
2) Rear turn signal light
3) Brake light 4) Tail light
5) Brake/tail light
2. Open the rear portion of the side trunk trim panel.
3. Remove the bulb holder from the rear combina-
tion light assembly by turning it counterclockwise.
4. Remove the bulb from the socket by pushing it
and turning counterclockwise. Install a new bulb.
5. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
6. Secure the rear trunk trim panel with the clips.

Maintenance and service
11-71
– CONTINUED –
Wagon
1. Using a Phillips screwdriver, remove the upper
and lower screws that secure the side cover of the
rear combination light assembly.
2. Remove the upper and lower screws. Then, slide
the rear combination lamp assembly to the rear and
remove it from the vehicle.