Page 85 of 210
1
4
3
5
2
6
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page13
2.13
QUICKSHIFT 5 GEARBOX
Selector lever
1Mode selection button: enables
you to move from manual mode to
automatic mode or from
automatic to manual mode at any
time with the engine running.
Note:The selector lever
automatically returns to the middle
position after use.Display
2automatic mode
3brake pedal depressed warning
light
4gear display
5not used
6gearbox fault warning light.
Thegearused(1,2..,5,N,R)is
indicated in the instrument panel
display. In automatic mode,(A)is
also displayed.
Driving
Switch on the ignition.
The display lights up on the
instrument panel.
As long as neutral is displayed (N),
start the engine but do not depress
the accelerator.
If a gear other than neutral(N)is
displayed this will flash;it will only
be possible to start the engine if you
press down the brake pedal (the
warning light3will come on if you
forget) when holding the key in
starting position.
The vehicle will then change to
neutral (N) automatically and the
engine will start.
Note: do not attempt to start the
engine by pushing the vehicle if the
battery is flat (the display remains
off when the ignition is switched
on).
Page 88 of 210
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page16
2.16
QUICKSHIFT 5 GEARBOX(continued)
Automatic mode
Automatic mode is selected by
default every time the ignition is
switched on.
You can change it at any time when
driving by pressing the mode
change button. The letterAappears
on the display.
The vehicle is controlled using the
accelerator and the brake. Gears will
change automatically at the correct
moment to a speed suitable for the
engine because the automatic
function takes into consideration
the weight of the car, the road
surface and the chosen driving
style.Note:
Automatic mode takes account of:
- the position and speed of
depression of the accelerator
pedal to assess driving style and
select the optimum gear,
- action on the brake pedal to alert
the engine brake by anticipating
the down-change
You can stop the vehicle at red
lights, with the gear engaged, by
pressing the brake pedal; there is no
need to change to neutral.
The vehicle will move off again:
- slowly, if you release just the brake
without accelerating (e.g. when in
a traffic jam)
- quickly, if you release the brake
and accelerate.
The level of oil in the
automatic gearbox system
reservoir is variable
depending on use. Adding
oil isstrictly forbidden(except by
qualified Renault network
personnel).
Page 89 of 210
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page17
2.17
QUICKSHIFT 5 GEARBOX(continued)
Accelerating and overtaking
You have two options:
1) slowly depress the accelerator
pedal to speed up gradually.
2) depress the accelerator pedal as
far as it will go (or: take your foot
off the pedal and depress the
pedal again until you reach the
point of resistance.
Parking
It is possible to park in gear (for
example, on a slope). To do this:
- with the ignition on, select a gear
with your foot on the brake.
- check that a gear other thanNis
displayed on the instrument
panel, then remove the ignition
key.
To disengage the gear, repeat this
operation by switching on the
ignition without starting the engine
and shift the selector lever to
neutralwith your foot on the brake.
Check thatNis displayed on the
instrument panel.
Page 90 of 210
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page18
2.18
QUICKSHIFT 5 GEARBOX(continued)
Horn
•If you keep the vehicle on a slope
for too long without applying the
brakes or handbrake, there is a
risk that the clutch will overheat.
In this event, an intermittent beep
will remind you that you should
put your foot on the brake or
apply the handbrake.
• Never leave the vehicle with the
engine running when in gear.
For safety reasons you will hear
an intermittent beep when you
open the door if you have not
shifted into neutral or you have
not switched off the ignition or
pressed the brake pedal.• Your vehicle will not start:
you can start the engine when the
vehicle is moving if the battery is
not discharged (display lit up).
Proceed as before:
- switch on the ignition
- select neutral
- push or tow the car or run it
down a slope until you reach the
speed at which the warning
buzzer is activated. This will
indicate that moving the
selector lever forwards will
engage the gear most suited to
starting the engine.
Note:never attempt this in reverse.
Operating faults
When driving,ifthis
warning light comes on, it
indicates a fault in the
system.
In most cases, you may still drive
the vehicle, although it will not
function perfectly. However, you
should consult a Renault Dealer as
soon as possible.
Towing a vehicle with a
sequential gearbox
If the gearbox is stuck in a gear:
- switch on the ignition
- select neutral with yourfoot on
the brake
- check that the gearbox is in neutral
(by pushing the vehicle, for
example).
If you cannot find neutral you must
tow the vehicle with the front
wheels raised.
Towing should always take place
with the ignition switched off.
Page 91 of 210
21
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page19
2.19
GEAR LEVER HANDBRAKEPOWER ASSISTED STEERING
To select reverse
(vehicle stationary)
Move the lever to neutral, then lift
up ring1against the gear lever knob
to select reverse gear.
The reversing lights illuminate as
soon as reverse gear is selected
(ignition on).
To release
Pull the lever up slightly, press in
button2and lower the lever to the
floor.
If you are driving with the
handbrake incorrectly released, the
red warning light on the instrument
panel will remain illuminated.
To apply
Pull the lever upwards.
The lever should travel about 10
notches to hold the vehicle. Your
vehicle has self adjusting rear brake
shoes and the handbrake should
only be adjusted during a brake
overhaul.
When the vehicle is
stationary, make sure
that the handbrake is
properly applied so that
the vehicle does not move
unintentionally.
Make sure the handbrake is
properly released when driving,
otherwise overheating may
occur.Never leave the steering on full lock
when the vehicle is parked (risk of
damaging the power assisted
steering pump).
Never switch off the
engine when travelling
downhill, and avoid
doing so when driving in
general (power steering and
brake servo will not function).
Page 100 of 210
2
1
3
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page28
2.28
ELECTRONIC STABILITY PROGRAM: ESP(continued)
Disabling the function
The function is deactivated by
pressing switch2, warning light1
will light up to confirm this.
This action also deactivates traction
control: see the information on the
traction control system in section 2.As the ESP offers additional safety,
it is recommended that you do not
drive when the function is disabled.
Correct this as soon as possible by
pressing button2again.
Note:ESP is automatically
reactivated when the ignition is
switched on.
Faults
When the system detects an
operating fault, warning lights1
and3light up.
Consult your Renault Dealer.
Page 102 of 210
2
1
3
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page30
2.30
TRACTION CONTROL SYSTEM(continued)
Disabling the function
In some situations (driving on very
wet ground: snow, mud,... or
driving with chained wheels), the
system may reduce the engine
power to limit skidding. It is
possible to deactivate the function
by pressing switch2if this is not
desirable.
Warning light1lights up.Disabling the traction control
function also deactivates the ESP
function: refer to the information on
the ESP in section 2.
Correct this as soon as possible by
pressing switch2again.
Note:traction control is
automatically reactivated when the
ignition is switched on.
Operating faults
When the system detects an
operating fault, warning lights1
and3light up.
Consult your Renault Dealer.
Page 125 of 210
13
2
A
B
Q X B I U D B * T [ G 3 D J H
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T3.WIN 30/10/2002 12:12-page23
3.23
INTERIOR LIGHTING
LightA
Tilt light1to give:
- continuous lighting,
- lighting controlled, depending on
version, by the opening of one of
the front doors, or by one of the
four doors. It only extinguishes
when the doors concerned are
correctly closed.
LightB
Tilt switch2to give:
- Continuous lighting.
- Lighting controlled, depending on
version, by opening one of the
front doors, or by one of the four
doors. It only extinguishes when
the doors concerned are correctly
closed.
- Lighting off.
- Lighting up of map reading light3.
Adjust map reading light3to the
required position.Automatic operation of interior
lighting (depending on the vehicle)
•If the doors are unlocked using
the plip remote control, the
interior lights are switched on for
approximately 15 seconds.
• If the doors are locked using the
plip remote control, the lights are
switched off immediately.
• If the door is open (or not
properly closed), the lights are
switched on for a period of
approximately 15 minutes.
• If all the doors are closed, the
interior lights start to dim when
the ignition is switched on.
