2003 Peugeot 406 key battery

17-02-2003
YOUR 406 IN DETAIL
104
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle.
DEADLOCKING
Deadlocking the doors is an addtional safety device.
Warning:The internal and external
door controls cannot operate when the vehicle is deadlocked.
There are two methods of operation:
With the the remote control
To deadlock: pressbutton A.
This is indicated by permanent lighting of the direction indicators for approxi-mately two seconds.
Press button A within five seconds
of deadlocking to change this to lock-
ing only.
This is indicated by permanent lightingof the direction indicators for approxi-mately two seconds.
With the ignition key from the driver's door
To deadlock: turn the key towards the rear of the vehicle.
To lock: within five seconds of deadlock- ing, again turn the key towards the rear
of the vehicle. To unlock: turn the keytowards the front of the vehicle.
Programming the remote control  Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key
from the ignition lock. The remotecontrol is now working again.
Changing the battery of theremote control
The information
''battery flat''is given by
an audible signal accompa-nied by a
message on the multifunction display.
To replace the battery, unclip thecasing using a coin at the ring(CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Do not operate the deadlock-ing if there is someone insidethe vehicle. Do not operate the buttons of
your remote control while it is in your pocket, as there is a possibility that itmay unlock your vehicle.

17-02-2003
THE ALARM SYSTEM*
This offers two types of protection: ¥external , it sounds if a door, the
bonnet or the boot is opened.
¥ internal , it sounds if there is air
movement in the passenger compartment (a broken windowor movement inside the vehicle) .
Note: it also has an anti-tamper
function; if there is an attempt to tam-per with the wires to the siren, the
control unit or the battery, the sirensounds and the direction indicatorslight. Setting
Switch the ignition off and get out of the vehicle. Set the alarm within five minutes fol- lowing your exit from the vehicle bylocking using the remote control (thered light on the switch, visible fromthe outside, flashes every secondand the direction indicators come onpermanently for two seconds).
5 seconds later, internal protection is set.
45 seconds later, external protection is set. When the alarm is triggered, the siren sounds for thirty seconds. After it has been triggered, the alarm is operational again. Note:
if you wish to lock your vehicle
without setting the alarm, lock it using the key in the lock.
Warning
When the alarm is triggered, if a door, the boot or the bonnet are not closed
correctly, the siren sounds for amoment. Close the vehicle correctlyto set the alarm. Disarming Unlock the vehicle using the remote
control key, (the direction indicatorsflash for two seconds and the redlight on the switch goes out). Note:
if the red warning light flashes,
it is a sign that the alarm has been triggered during your absence.
To stop it, switch on the ignition.Note: when the alarm is set, but the
remote control no longer works:
¥ unlock the doors using the key and open the door; the alarm is trig- gered;
¥ switch the ignition on within ten seconds;
¥ press the internal protection button 1 immediately. The alarm is dis-
armed.
* According to destination.
YOUR 406 IN DETAIL
106

17-02-2003
ELECTRIC WINDOWS
1 - Driver's electric window switch.You have two options:
Ð Manual operation:Press or pull switch 1gently.
The window stops as soon as the switch is released.
Ð Automatic operation: Press or pull switch 1fully. The
window opens or closes com-pletely when the switch isreleased. Pressing the switchagain stops the movement of
the window.
YOUR 406 IN DETAIL 141
Safety auto-reverse When the window on the driver's side rises and meets an obstacle,it stops and lowers again. Notes: In the case of unwanted opening of the window on closing (forexample, in the case of frost) ifthe window will not rise and goesinto safety auto-reverse mode,lower it completely and raise it
again immediately, by pulling theswitch until the window closes
completely. Continue to press theswitch for approximately one sec-ond after closing. Following reconnection of the
battery, in the event of a malfunc-tion, you must reinitialise thesafety auto-reverse function:
Ð open the window completely,
then close it, it will rise in stages of a few centimetreswith each press, repeat theoperation until the window iscompletely closed,
Ð continue to press the switch for at least one second afterreaching this position.
The safety auto-reverse func-tion is not operational duringthese operations. 2 - Passenger's electric window
switch.
3 - Rear left electric window switch.
4 - Rear right electric window switch.
5 - Disarming the rear window switches (child safety). For the safety of your children, press switch 5to prevent opera-
tion of the rear windows irrespec-tive of their position. The 1st press activates the switch and the 2nd press deacti-vates it.
Always remove the key from the ignition whenleaving the vehicle, evenfor a short time.
In the event of contact whenoperating the windows, you mustreverse the movement of the
window. To do this, press theswitch concerned. When the driver operates the passenger window switches, hemust ensure that no one ispreventing correct closing of the
window. The driver must ensure that passengers use the electric
windows correctly. Be aware of children when operating the windows.

17-02-2003
BATTERY
To charge the battery using a battery charger:
Ð Disconnect the battery,
Ð Follow the instructions for use given by the battery charger manufacturer,
Ð Reconnect starting with the negative (Ð) terminal,
Ð Check that the terminals and connectors are clean. If they are covered with sul-phate (white or greenish deposit), disconnect them and clean them.
To start the vehicle from another battery:
Ð Connect the red cable to the positive (+) terminals of the two batteries,
Ð Connect one end of the green or black cable to the negative (Ð) terminal of the slave battery,
Ð Connect the other end of the green or black cable to an earth point on the bro- ken down vehicle, as far as possible from the battery,
Operate the starter, let the engine run.
Wait for the engine to return to idle, then disconnect the cables.
Ð Never disconnect a terminal when the engine is running.
Ð Never charge a battery without first disconnecting the terminals.
Ð Close the sunroof before disconnecting the battery. If it does not operate normally following re-connection of the battery, you must
re-initialise it by turning the control to the maximum tilt position and pressing it for a few seconds.
Ð After every reconnection of the battery, switch on the ignition and wait 1 minute before starting to allow the electronic systems to be initialised. Ifslight difficulties are experienced after this, please contact a PEUGEOT deal-
er.
It is advisable to disconnect the battery if the vehicle
is not to be used for a period of more than one month.
Economy mode
With the engine switched off and the ignition key in the "running" or"accessories" position for about half
an hour, certain electrical equipment(displays, instrument panel, warninglights, courtesy lights, electric win-
dows, wipers etc.) will switch offautomatically to avoid draining the
battery. Once the electrical equipment goes into economy mode, it is necessaryto start the engine to enable theequipment to work again.
MAINTENANCE OF YOUR 406
46