2003 Peugeot 406 Dag ignition

17-02-2003
Main menu Switch on the ignition. Press the "Menu"button to access the main menu.
Select a function using the direction arrows, then confirm ( "VAL" button). The
"Navigation/guidance" menu offers the following
options:
Ð entering of the address of a new destination.
Ð selection of a service (Hotel, station, airport...) available in a town.
Ð selection of an address stored in one of the two directories.
Ð access to the "Navigation options" menu;
Ð radio functions are suspended when the system is in guidance mode.
YOUR 406 IN DETAIL
96
Navigation/Guidance Following selection of the "Navigation/guidance"menu,
a screen warns you about the use of the navigation sys- tem. Follow the regulations in force and do not use theremote control while driving. Press the "VAL"button to access the next screen.

17-02-2003
Recalling a memorised position
¥ Door open and ignition off Within ten minutes of switching off
the ignition and opening the door, ashort press on button 1or 2recalls
the memorised position of the seat,then of the exterior mirrors.
¥ Door closed or ignition on: Ð keeping the button pressedadjusts the seat and the exteriormirrors.
When adjustment is completed ableep will sound.
YOUR 406 IN DETAIL 113
Memorising the seat and mirror positions
Two driving positions can be memo- rised.
To memorise:
Ð place the ignition key in the acces-
sories position;
Ð adjust your seat and mirrors;
Ð simultaneously press button " M"
and button " 1" for the first driving
position or button " 2" for the
second driving position. When the position has been memorised, you will hear twobleeps. Memorising a new position cancels the previous one. Heated seat controls Press the switch.The temperature is controlled auto-
matically. Pressing a second time stops opera- tion.

17-02-2003
SEAT BELTS
To adjust the height of the front seat belts Pinch control 1and slide it.
To lock the seat beltsPull the strap, then insert the buckle into the stalk. Pre-tensioning and force-limitingfront seat belts Safety in the event of a frontal impact has been improved by the introduc-tion of pre-tensioning and force-limit-ing front seat belts. Depending onthe seriousness of the impact, thepre-tensioning system instantly tight-ens the seat belt firmly against thebody of the occupant. The pre-tensioning seat belts are active when the ignition is on. The force-limiting device reduces the pressure of the seat belt against theoccupant's body in the event of anaccident. Rear seat belts The three rear seats are all fitted with three-point inertia reel belts.
YOUR 406 IN DETAIL
123
To be effective, a seat belt must be tightened asclose to the body as pos-sible.
Depending on the nature and theseriousness of the impact, thepre-tensioners may be triggeredbefore and independently of theair bags. In all cases, the air bag warning light comes on. Following a collision, have the system checked by a PEUGEOT
dealer. The system has been designed to be fully operational for ten years. Have it replaced after this period.

17-02-2003
THE KEYS The keys allow you to switch on the ignition and to independently operate
the locks on the front door, the glovebox and the passenger air bag dis-arming switch. Central locking
From the driver's door, the keys allow you to lock and unlock thedoors and boot/tailgate. If one of the front or rear doors is open, the central locking does notwork. The remote control performs the same functions at a distance. The remote control LockingPress button Ato lock the vehicle.
YOUR 406 IN DETAIL 103
This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds. Unlocking Press button
B to unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk caus-ing it not to work and the remote con-trol would have to be reprogrammed. ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code isrecognised and starting is possible. If the system does not function cor-
rectly, you are warned by an audiblesignal and a message on the multi-
function display. In this case, the vehicle will not start.
Contact a PEUGEOT dealer as soon as possible.
Locating your vehicle
To locate your vehicle, if you have locked it, in a car park: 
press button A. The courtesy
lights come on and the direction indicators flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.

17-02-2003
YOUR 406 IN DETAIL
104
Changing the battery of the remote control The information ''battery flat''is
given by an audible signal accompa- nied by a message on the multi-
function display.
To replace the battery, unclip the casing using a coin at the ring(CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Programming the remote control 
Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key
from the ignition lock. The remotecontrol is now working again.

17-02-2003
YOUR 406 IN DETAIL105
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the key is lost, your PEUGEOT dealer can rapidly supply you with new keys.
The high-frequency remote control is a high-performance system. Do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle without your knowledge. The remote control cannot operate if the key is in the ignition, even if the ignition is switched off, except for reprogramming .
Do not operate the deadlock if there is someone inside the vehicle.As a safety measure (when there are children on board), remove the ignition key when leaving the vehicle, even for a short time. Do not handle the buttons of your remote control when out of range of your vehicle as you run the risk of stopping it from working. It would then be necessary to reprogramme the remote control. When buying a second-hand car:
Ð ensure that you are in possession of the confidential card;
Ð have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones that can start your vehicle.
Do not make any modifications to the electronic engine immobiliser system.

17-02-2003
THE KEYS The keys allow you to switch on the ignition and to independently operate
the locks on the front door, the glovebox and the passenger air bag dis-arming switch. Central locking
From the driver's door, the keys allow you to lock and unlock thedoors and boot/tailgate. If one of the front or rear doors is open, the central locking does notwork. The remote control performs the same functions at a distance. The remote control LockingPress button Ato lock the vehicle.
YOUR 406 IN DETAIL 103
This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds. Unlocking Press button
B to unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk caus-ing it not to work and the remote con-trol would have to be reprogrammed. ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code isrecognised and starting is possible. If the system does not function cor-
rectly, you are warned by an audiblesignal and a message on the multi-
function display. In this case, the vehicle will not start.
Contact a PEUGEOT dealer as soon as possible.
Locating your vehicle
To locate your vehicle, if you have locked it, in a car park: 
press button A. The courtesy
lights come on and the direction indicators flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.

17-02-2003
THE ALARM SYSTEM*
This offers two types of protection: ¥external , it sounds if a door, the
bonnet or the boot is opened.
¥ internal , it sounds if there is air
movement in the passenger compartment (a broken windowor movement inside the vehicle) .
Note: it also has an anti-tamper
function; if there is an attempt to tam-per with the wires to the siren, the
control unit or the battery, the sirensounds and the direction indicatorslight. Setting
Switch the ignition off and get out of the vehicle. Set the alarm within five minutes fol- lowing your exit from the vehicle bylocking using the remote control (thered light on the switch, visible fromthe outside, flashes every secondand the direction indicators come onpermanently for two seconds).
5 seconds later, internal protection is set.
45 seconds later, external protection is set. When the alarm is triggered, the siren sounds for thirty seconds. After it has been triggered, the alarm is operational again. Note:
if you wish to lock your vehi-
cle without setting the alarm, lock it using the lock.
Warning
When the alarm is triggered, if a door, the boot or the bonnet are not closed
correctly, the siren sounds for amoment. Close the vehicle correctlyto set the alarm. Disarming Unlock the vehicle using the remote
control key. (the direction indicatorsflash for two seconds and the redlight on the switch goes out). Note:
if the red warning light flashes,
it is a sign that the alarm has been triggered during your absence.
To stop it, switch on the ignition.Note: when the alarm is set, but the
remote control no longer works:
¥ unlock the doors using the key and open the door; the alarm is trig- gered;
¥ switch the ignition on within ten seconds;
¥ press the internal protection button 1 immediately. The alarm is dis-
armed.
* According to destination.
YOUR 406 IN DETAIL
106