2003 Peugeot 406 C warning

24-03-2003
Door open warning light When the engine is running, the warning light indicatesthat a door has not been
closed properly or that the boot isopen.
Electronic immobiliser warning light This indicates a malfunction
of the electronic immobiliser.
Contact a PEUGEOT dealer.
Low fuel level warning light. When this warning light comes on, you
have enough fuel remaining to drive
at least 30 miles (50 km). The tankcapacity is approximately 70 litres(15.4 gallons). Coolant temperature indicator When the needle is in zone
A,the
temperature is correct.When the needle is in zone B, the
temperature is too high. The central
(STOP) warning light flashes. Y ou must stop immediately.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light With the engine running, the indicator light comes onwhen the driver's seat belt isnot fastened.
YOUR 406 COUPE IN DETAIL
110

24-03-2003
Door open warning light When the engine is running, the warning light indicatesthat a door has not been
closed properly or that the boot isopen.
Electronic immobiliser warning light This indicates a malfunction
of the electronic immobiliser.
Contact a PEUGEOT dealer.
Low fuel level warning light. When this warning light comes on, you
have enough fuel remaining to drive
at least 30 miles (50 km). The tankcapacity is approximately 70 litres(15.4 gallons). Coolant temperature indicator When the needle is in zone
A,the
temperature is correct.When the needle is in zone B, the
temperature is too high. The central
(STOP) warning light flashes. Y ou must stop immediately.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light With the engine running, the indicator light comes onwhen the driver's seat belt isnot fastened.
YOUR 406 COUPE IN DETAIL
110

24-03-2003
This enables the following information to be displayed: -the time,
-t he date,
- the outside temperature (the ¡C symbol flashes when there is a risk of ice),
- the radio displays,
- the status of the doors. The display shows you whether a door, the boot or the bonnet is open and if the fuel filler cap is missing.
- the warning messages (e.g. ''battery low'') or information messages (e.g. "top
up fuel tank''), displayed temporarily, can be cleared by pressing button 1or
2 ,
- the trip computer.
Setting the parameters Press button 1for two seconds to access the settings. The information flashes
to show it is ready to be modified.Then, individual presses on button 1 allow you to scroll through the various data
in the following sequence: - language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (Celsius or Fahrenheit),
- time format (12 then 24 hour mode)
- hour,
- minutes,
- year,
- month,
- day,
Pressing button 2allows you to change the information selected. Maintain the
pressure for rapid scrolling. After ten seconds without action, the display returns to the main screen and the modified data are recorded.Display B
YOUR 406 COUPE IN DETAIL
114

24-03-2003
Display CThis enables the following information to be displayed: Ðthe time,
Ð the date,
Ð the outside temperature (the ¡C symbol flashes when there is a risk of ice),
Ð the radio displays,
Ð the status of the doors. The display shows you whether a door, the boot or the bonnet is open,
Ð the warning messages are displayed temporarily (e.g. "top up fuel tank'') andcan be cleared using the remote control,
Ð the trip computer (see following page),
Ð the satellite navigation system (see corresponding section),
Ð the name of the road along which the vehicle is travelling (permanent loca-ting).
Setting the parameters
The remote control allows you to access the settings. Accessing the different menus is described in the section on the Satellite Navigation System. Permanent locating This function makes it possible to display the name of the road along which the vehicle is travelling when guidance is not activated. Press the "MODE" button on the remote control to display the name of the road
along which you are travelling.
To "ZOOM" in order to display the information more clearly, press the right arrow
on the remote control.W ARNING: the CD ROM containing the map data must be in the drive.
YOUR 406 COUPE IN DETAIL 115

24-03-2003
SEAT BELTS
To adjust the height of the front
seat belts Pinch control 1and slide it.
To lock the seat belts
Pull the strap, then insert the buckle into the stalk. Pre-tensioning and force-limitingfront seat belts Safety in the event of a frontal impact has been improved by the introduc-tion of pre-tensioning and force-limit-ing front seat belts. Depending onthe seriousness of the impact, thepre-tensioning system instantly tight-ens the seat belt firmly against thebody of the occupant. The pre-tensioning seat belts are active when the ignition is on. The force-limiting device reduces the pressure of the seat belt against theoccupant's body in the event of anaccident. Rear seat belts The rear seats are fitted with two three-point inertia reel belts.
YOUR 406 COUPE IN DETAIL
101
To
be effective, a seat
belt must be tightened as close to the body as pos-sible.
Depending on the nature and theseriousness of the impact, thepre-tensioners may be triggeredbefore and independently of theair bags. In all cases, the air bag warning light comes on. Following a collision, have the system checked by a PEUGEOT
dealer. The system has been designed to be fully operational for ten years. Have it replaced after this period.

24-03-2003
YOUR 406 COUPE IN DETAIL87
THE ALARM SYSTEM*
This offers two types of protection: ¥
external , it sounds if a door, the
bonnet or the boot is opened.
¥ internal , it sounds if there is air
movement in the passenger compartment (a broken windowor movement inside the vehicle).
Note: it also has an anti-tamper
function; if there is an attempt to tam-per with the wires to the siren, the
control unit or the battery, the sirensounds and the direction indicatorslight. Setting
Switch the ignition off and get out of the vehicle. Set the alarm within five minutes fol- lowing your exit from the vehicle bylocking using the remote control (thered light on the switch, visible fromthe outside, flashes every secondand the direction indicators come onpermanently for two seconds).
5 seconds later, internal protection is set.
45 seconds later, external protection is set. When the alarm is triggered, the siren sounds for thirty seconds. After it has been triggered, the alarm is operational again. Note:
if you wish to lock your vehicle
without setting the alarm, lock it using the lock. W arning
When the alarm is triggered, if a
door, the bootor the bonnet are not
closed correctly, the siren sounds fora moment. Close the vehicle correct-ly to set the alarm. Disarming Unlock the vehicle using the remote control key (the direction indicatorsflash for two seconds and the redlight on the switch goes out). Note:
if the red warning light flashes,
it is a sign that the alarm has been
triggered during your absence. Tostop it, switch on the ignition. Note: when the alarm is set, but the
remote control no longer works:¥ unlock the doors using the key and open the door; the alarm is trigge-red;
¥ switch the ignition on within tenseconds;
¥ press the internal protection button1 immediately. The alarm is disar-
med.
* According to destination.

24-03-2003
YOUR 406 COUPE IN DETAIL
88
Do not make any modifi- cations to the alarm sys-tem, this could causefaults.
To
set the alarm to external
protection only If you want to leave a window par- tially open, or a pet inside thevehicle, you need to select externalprotection only: ¥ Switch off the ignition.
¥W ithin the next ten seconds, press
the internal protection button 1
until the light comes on.
¥ Get out of the vehicle.
¥ Press the locking button on the remote control.
¥ The doors lock.
¥ The direction indicators light fortwo seconds.
¥ The red light on the switch flashesonce a second. To
disarm external type
protection only ¥ see "Disarming" section.
Note: if you wish to charge or repla-
ce the battery:¥T urn on the ignition.
¥Y ou have 10 seconds after turning
on the ignition to press the internal protection switch 1and hold it
down for two seconds.
¥ The warning light flashes rapidlyfor three seconds.
¥ Disconnect the battery.
¥ After reconnecting the battery,lock, then unlock the vehicle usingthe remote control.

24-03-2003
AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function:
☞ Place the key in the accessories position (1st notch),
☞ Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multifunction display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multifunction display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by: - manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this:
☞ place the lights stalk in the AUTO
position,
☞ place the key in the accessories position (first notch),
☞ press the end of the lights stalk formore than two seconds,
☞ place the lights stalk in the 0posi-
tion,
☞ flash the headlamps,
☞ get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103