2003 Peugeot 406 C key

24-03-2003
THE KEYS The keys allow you to switch on the ignition and to independently operatethe locks on the doors, the fuel fillercap, the glove box and the passen-ger air bag disarming switch. Central locking From the doors (keeping the key turned in the locked position for afew seconds) the keys allow you tolock, deadlock and unlock the doorsand the boot, as well as fold back theexterior mirrors. If one of the front doors or the boot is open, central locking is not possible.In this case a bleep indicates lockingby remote control. The remote control performs the same functions at a distance.The remote control Deadlocking Deadlocking renders ithe internal and external door controls inopera-tive. Press button
Ato deadlock the vehi-
cle. This is confirmed by fixed light- ing of the direction indicators forapproximately two seconds. Another press on button A, within
five seconds of deadlocking, changes this to normal locking .
This is confirmed by fixed ighting ofthe direction indicators for approxi-mately two seconds, accompaniedby a brief sound of the horn. Unlocking Press button Bto unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note:
avoid handling the button of
your remote control when out of
range of your vehicle. You run therisk of stopping it from working. Itwould then be necessary to repro-gramme the remote control.
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code.When the ignition is switched on, thecode is recognised and starting ispossible. If the system does not function correctly , contact a PEUGEOT
dealer as soon as possible.
YOUR 406 COUPE IN DETAIL
84

24-03-2003
YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information
"battery flat"is
given by an audible signal accompa- nied by a message on the multifunc-
tion display.
To replace the battery, unclip the
casing using a coin at the ring (CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Key in ignition A
buzzer sounds on opening the dri-
ver's door, if the key has been left in the ignition. Locating your car
To locate your car, if you have locked
it, in a car park:
☞ press button A.The courtesy
lights come on and the direction indicators flash for a few seconds.
Programming the remote control
☞ Switch off the ignition.
☞ Switch the ignition on again.
☞ Press button Aimmediately.
☞ Switch off the ignition and remove the remote control key from the
ignition lock. The remote controlis now working again.

24-03-2003
YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock your vehicle, without you being aware of it.The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except for reprogramming.
However, do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.Do not repeatedly press the button of your remote control out of range of your vehicle. Y ou run the risk of stopping it from working and the remote control would have to be reprogrammed.
When purchasing a second-hand vehicle:- ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.

24-03-2003
YOUR 406 COUPE IN DETAIL87
THE ALARM SYSTEM*
This offers two types of protection: ¥
external , it sounds if a door, the
bonnet or the boot is opened.
¥ internal , it sounds if there is air
movement in the passenger compartment (a broken windowor movement inside the vehicle).
Note: it also has an anti-tamper
function; if there is an attempt to tam-per with the wires to the siren, the
control unit or the battery, the sirensounds and the direction indicatorslight. Setting
Switch the ignition off and get out of the vehicle. Set the alarm within five minutes fol- lowing your exit from the vehicle bylocking using the remote control (thered light on the switch, visible fromthe outside, flashes every secondand the direction indicators come onpermanently for two seconds).
5 seconds later, internal protection is set.
45 seconds later, external protection is set. When the alarm is triggered, the siren sounds for thirty seconds. After it has been triggered, the alarm is operational again. Note:
if you wish to lock your vehicle
without setting the alarm, lock it using the lock. W arning
When the alarm is triggered, if a
door, the bootor the bonnet are not
closed correctly, the siren sounds fora moment. Close the vehicle correct-ly to set the alarm. Disarming Unlock the vehicle using the remote control key (the direction indicatorsflash for two seconds and the redlight on the switch goes out). Note:
if the red warning light flashes,
it is a sign that the alarm has been
triggered during your absence. Tostop it, switch on the ignition. Note: when the alarm is set, but the
remote control no longer works:¥ unlock the doors using the key and open the door; the alarm is trigge-red;
¥ switch the ignition on within tenseconds;
¥ press the internal protection button1 immediately. The alarm is disar-
med.
* According to destination.

24-03-2003
YOUR 406 COUPE IN DETAIL91
BOOT Simultaneous locking or unlock- ing of the boot and the doors T
urn the key a quarter turn from Ato
B .
The boot is then controlled by the remote control or the driver's doorlock. Locking the boot only T urn the key a quarter of a turn from
A to C. The boot is then locked,
whatever the action of the remote control or the driver's door lock.
To return to simultaneous operation
with the doors: turn the key from Ato
B .OPENING THE BONNET From inside: pull the handle on the
left-hand side under the fascia.From outside: lift the catch and
raise the bonnet. Bonnet struts These open the bonnet and hold it open.
To close
Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. FILLING WITH FUEL Fill with fuel with the engine switched
off.
To
open the fuel filler flap, firmly pull
the handle on the floor on the outside of the driver's seat. If you are filling up your tank, do not
continue after the 3rd cut-off of thepump; this could cause your vehicleto malfunction. The capacity of the tank is approx- imately 15.4 gallons (70 litres). A filler cap hook is provided on
the inside of the fuel filler flap.

24-03-2003
AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function:
☞ Place the key in the accessories position (1st notch),
☞ Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multifunction display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multifunction display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by: - manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this:
☞ place the lights stalk in the AUTO
position,
☞ place the key in the accessories position (first notch),
☞ press the end of the lights stalk formore than two seconds,
☞ place the lights stalk in the 0posi-
tion,
☞ flash the headlamps,
☞ get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103

Always remove the key from the ignition whenleaving the vehicle, evenfor a short time.
In the event of contact when ope-rating the windows, you mustreverse the movement of the win-
dow. To do this, press the switchconcerned. When the driver operates the passenger window switches, hemust ensure that no one is pre-venting correct closing of the win-
dow. The driver must ensure that pas- sengers use the electric windows
correctly. Be aware of children when opera- ting the windows.
ELECTRIC WINDOWS
1 - Driver's electric window switch
Y ou have two options:
- Manual operation: Press or pull switch 1gently. The
windows stops as soon as the swit- ch is released.
- Automatic operation*: Press or pull switch 1fully. The
window opens or closes complete- ly when the switch is released.Pressing the switch again stops
the movement of the window.
Note: In the case of unwanted opening of the window on closing (for examplein the case of frost), if the window willnot rise, lower it completely and raise
it again immediately, by pulling theswitch until the window closes com-
pletely. Continue to press the switch for approximately one second after clo-sing. Following reconnection of the batte-
ry, in the event of a malfunction, youmust reinitialise the driver's electricwindow: -
it is essential to close the doors,
- open the window completely, then close it, it will rise in stages of a fewcentimetres with each press,repeat the operation until the win-dow is completely closed,
- continue to press the switch for atleast one second after reachingthis position.
2 - Passenger's electric window switch
YOUR 406 COUPE IN DETAIL
118
* According to country24-03-2003

24-03-2003
Sun visor with illuminated courtesy mirror With the ignition on, the mirror is automatically lit up when the flap isopened.
YOUR 406 COUPE IN DETAIL
122
COURTESY LIGHTS Off. On when one of the doors is opened. Permanently on when the ignition key is in the accessories position or the ignition is on.
1 - Front courtesy light.
2 - Rear courtesy light.
3 - Map-reading lights. With the key in the accessories position or the ignition on, operate the rele- vant switch.
Coat hook Press the lower section to extract the hook from its housing.