2003 Peugeot 406 Break Dag Owner's Manual

17-02-2003
MAINTENANCE OF YOUR 406
36
Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), thechrome trim and then the plasticcover must be removed using tool 7,
before unscrewing the bolt using oneof the two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the confidential card) and thewheel brace 1.
Note: make a careful note of the
code number engraved on the head
of the anti-theft socket. This willenable you to obtain duplicate anti-
theft sockets from a Peugeot dealer.
* According to model and destination.
Special features of alloy wheels Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool 7to remove the trims before
slackening the bolts.Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is normal to notice when tightening the
bolts that the washers do not come
into contact with the rim. The sparewheel is secured by the cone-shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels to your vehicle, it is essential
to use special bolts available from
your PEUGEOT dealer.

17-02-2003
PETROL/LPG TWIN FUEL VERSION169
Puncture Insulated storage compartment This is located in the boot and con- tains:
Ð the temporary tyre repair cans 1
(your 406 LPG does not have a spare wheel),
Ð the adaptors 2 necessary for
filling the LPG tank in some countries,
Ð the towing eye 3.
Fuses The LPG functions are protected by the two fuses Ain the fuse box
located in the engine compartment.
Using the repair cans (Refer to the directions on the cans also)
Ð if possible, remove the object
which caused the puncture,
Ð rotate the wheel so that the valve is in the same position as the figures 2 or 10 on a clock,
Ð shake the cans vigorously before use. In very cold weather, warmthe cans between your hands forfew minutes,
Ð hold the valve with one hand and with the other press the injectionnozzle on the can firmly onto thevalve, holding it straight,
Ð maintain the pressure firmly for one minute, Ð carry out the same operation with
the second can, then drive imme-
diately, at a moderate speed , to
the nearest garage.
The cans enable you to carry out
a temporary repair. After use, the tyre must be changed. As the cans are pressurized, they must not be exposed to a temper-ature above 50 ¡C. Store them away from heat in the insulated storage compartment.

17-02-2003
Amber bulbs must be replaced by bulbs of iden-tical specification and
colour.
In certain weather conditions (lowtemperatures, humidity), the
presence of condensation onthe inside of the headlampglass is normal; it disappears a
few minutes after the lights havebeen switched on.
CHANGING A BULB 1 - Dipped beam headlamps 2 - Main beam headlamps 2 bulbs (H7-55 W)
Ð Press the tab and remove the protective cover corresponding to the faulty bulb.
Ð Disconnect the connector.
Ð Press the end of the securing clip to remove it. Change the bulb.
Ð When fitting, ensure that the direction notches are positioned correctly and that the securing clip is corrrectly fixed.
Ð Reconnect the connector.
Ð Refit the protective cover. 3 - Side lights (W 5 W)
Turn the socket using the lever and remove it. Change the bulb.
4 - Direction indicators (P 21 W)
Turn the bulb holder a quarter turn and remove it. Change the bulb. Note: only handle H7 bulbs using a dry cloth.
To replace the left-hand bulbs, remove the protective battery cover. Direction indicator (WY 5 W)
Ð Pull the rear section of the trans-
parent cover and release the
assembly.
Ð Turn the connector a quarter turn and remove it.
Ð Change the bulb.
MAINTENANCE OF YOUR 406 37

17-02-2003
Third brake light - saloon (5 W5W bulbs) Lower the two metal clips on either side of the light and slide the cover
towards the rear.
Remove the bulb-holder.Change the faulty bulb.Rear lights, saloon
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W).
3 - Brake lights/Side lights (P 21/5 W).
4 - Side lights (P 21/5 W).
5 - Fog lamp (P 21 W). These 5 bulbs are changed from inside the boot:
Ð remove the retaining clips then release the carpet,
Ð remove the connector by pressing the tab
A,
Ð remove the bulb holder by squeezing the tabs,
Ð change the faulty bulb.
MAINTENANCE OF YOUR 406
38

17-02-2003
Tailgate lights Open the flap using the cut-out pro- vided. Disconnect the connector by releas- ing tab A.
Unscrew the two nuts. Remove the light by squeezing the two tabs B. Extract the bulb holder by pressingthe tabs
C.
Change the faulty bulb.
1 - Side lights (P 21/5 W).
2 - Reversing lights (P 21 W).
3 - Fog lamp (P 21 W). Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
MAINTENANCE OF YOUR 406
40

17-02-2003
Rear lights, estate
Wing lights
To remove the trim, pull the handle towards you and release the panelupwards.Open the flap using the ignition key. Remove the connector by pressing the metal bar
A.
Unscrew the wing nut B.
Release the light. To gain access to the bulbs, press
the tabs and release the bulb holder.
1 - Brake/side lights (P 21/5 W).
2 - Direction indicators (P 21 W). Change the faulty bulb.
MAINTENANCE OF YOUR 406
39

17-02-2003
Tailgate lights Open the flap using the cut-out pro- vided. Disconnect the connector by releas- ing tab A.
Unscrew the two nuts. Remove the light by squeezing the two tabs B. Extract the bulb holder by pressingthe tabs
C.
Change the faulty bulb.
1 - Side lights (P 21/5 W).
2 - Reversing lights (P 21 W).
3 - Fog lamp (P 21 W). Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
MAINTENANCE OF YOUR 406
40

17-02-2003
CHANGING A FUSE The fuse boxes are under the fascia and in the engine compartment. Fascia fuse box
Turn the three screws a quarter turn with a coin. Pull at Aand tilt the
cover to access the fuses. Removing and changing a fuse Before changing a fuse you must find out the cause of the fault and have it put
right. The fuse numbers are indicated on the fuse box. Use the special pliers
Aattached to the box.
Always change a faulty fuse for one of the same rating.
Correct Incorrect Pliers A
Remove the fascia panel lower trim to access the built-in systems interface.
Fuse n o
. Rating Functions
A 20 A Locking/Unlocking.
B 10 A Rear fog lamps.
.
C 40 A Demisting of mirrors.
D 15 A Rear screen wiper.
E 30 A Electric windows.
F 15 A Supply to: Instrument panel,
Display, Audio equipment,Satellite navigation system,Air conditioning.
MAINTENANCE OF YOUR 406 41