2003 Peugeot 307 CC display

22-09-2003
YOUR 307 CC IN DETAIL103
AUTOMATIC SWITCHING ON OF LIGHTS The side lights and dipped beam headlamps switch on automatically ifthe light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light becomes bright enough or the wind-
screen wipers are switched off. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function:
Ð Place the key in the accessories
position (1st notch),
Ð Press the end of the lights stalk for more than four seconds.
Note: In foggy weather or in snow,
the brightness sensor can detect suf-
ficient light. As a result, the lights will
not come on automatically.
The brightness sensor, coupled
with the rain sensor, is located inthe centre of the windscreen,
behind the interior mirror. It isused for automatic switching onof the lights. Operating check ActivationActivation of this function is accom- panied by an audible signal and themessage
"Automatic lighting
active" on the multifunction display.
Disarming Disarming of the function is accom- panied by an audible signal. Note: the function is temporarily
disarmed when the driver uses the manual lighting controls. If the brightness sensor does not function correctly , the system acti-
vates the function (the lights come
on). The driver is alerted by an audi-ble signal, accompanied by the mes-sage "Auto lighting fault" on the
multifunction display.
Contact a PEUGEOT dealer to have the system checked.
Direction indicators (flashers)
Left: downwards.
Right: upwards.

22-09-2003
YOUR 307 CC IN DETAIL105
Automatic windscreen wipers In the
AUTOposition, the wind-
screen wipers operate automatically and adapt their speed to the inten-
sity of the rainfall.
Operating check ActivationWhen the function is activated, the message "Automatic wiping
active" appears on the multi-func-
tion display. Disarming In the event of malfunction , the dri-
ver is informed by an audible signal and the message "Auto wiper fault"
on the multi-function display. In the AUTOposition, the wind-
screen wiper will operate in intermit- tent mode.
Contact a PEUGEOT dealer to have the system checked. Do not cover the rain sen-sor located on the wind-screen behind the interior
mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.

22-09-2003
YOUR 307 CC IN DETAIL105
Automatic windscreen wipers In the
AUTOposition, the wind-
screen wipers operate automatically and adapt their speed to the inten-
sity of the rainfall.
Operating check ActivationWhen the function is activated, the message "Automatic wiping
active" appears on the multi-func-
tion display. Disarming In the event of malfunction , the dri-
ver is informed by an audible signal and the message "Auto wiper fault"
on the multi-function display. In the AUTOposition, the wind-
screen wiper will operate in intermit- tent mode.
Contact a PEUGEOT dealer to have the system checked. Do not cover the rain sen-sor located on the wind-screen behind the interior
mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.

22-09-2003
YOUR 307 CC IN DETAIL
108
Trip computer configuration This function allows the distance to the destination to be input (whenguidance is not activated; otherwisethis information is given by the navi-gation system) and also changing of
the units of measurement (¡C or ¡F,km and litres or miles and gallons). Distance to destination When guidance is not activated, this enables an approximate value to beentered to make all the trip computercalculations possible.
Specific features of the monochrome screen CT and the colour screen DT General menu Press the
"MENU" button to access
the general menu.Select the icon "Trip computer"
using the dial, then validate to
access the ''Trip computer'' menu.
The ''trip computer'' menu offers var- ious choices:
Ð Trip computer configuration,
Ð Warning log.
"Trip computer" context menu The context menu associated with the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli-cation currently being used in the
main screen window. Briefly press the continuous applica-
tion "Trip computer" button to selectone of the following functions:
Ð Warning log,
Ð Distance to destination.