MA-4
DESCRIPTION
DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsBLS0005D
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD — engine off
Radiator coolant level and coolant hose connections for leaks
Battery fluid level, specific gravity and conditions of battery terminals
Drive belts tension
Fuel lines and connections for leaks
Engine oil level and oil leaks
Brake reservoir fluid level and fluid lines for leaks
Windshield and rear window washer and headlamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for operation
All moldings, trims and fittings for fit and alignment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and alignment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if applicable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If applicable)
Install deodorizing filter to air conditioner (If applicable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Transfer and differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for leaks
Tighten bolts and nuts of steering linkage and gear box, suspension, propeller shafts and drive shafts
Tighten rear body bolts and nuts (Models with wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing and kickdown
Steering control and returnables
Engine performance
HEATED SEAT
SE-61
C
D
E
F
G
H
J
K
L
MA
B
SE
HEATED SEATPFP:87335
System Description BIS0013C
Each seat cushion has seat heater unit.
Front heated seat is composed the following
–Heated seat relay
–Front heated seat switch
–Seat heater unit
Rear heated seat is composed the following
–Heated seat relay
–Heated seat switch
–Seat heater unit
–Heated seat control unit
Heated seat system has two operation pattern, LOW and HIGH.
NOTE:
When handling seat, be extremely careful not to scratch seat heater unit
To replace heating unit, seat trim and pad should be separated.
Do not use any organic solvent, such as thinner, benzene, alcohol, etc. to clean trims.
FRONT HEATED SEAT
When ignition switch is ON or START, heated seat relay activates.
Then power is supplied
through 10A fuse [No. 8, located in fuse block (J/B)]
through heated seat relay terminals 3 and 5
to front heated seat switch (driver side and passenger side) terminal 1.
Driver Side
LOW FUNCTION
When front heated seat switch (driver side) is in LOW position, power is supplied
through front heated seat switch (driver side) terminal 2
to seat heater (driver side) terminals 53.
And, ground is supplied
to seat heater terminal 52
through grounds B16 and B17.
Then seat heater (driver side) LOW function is activated.
At this time ground is supplied
to front heated seat switch (driver side) terminal 4
through grounds M71 and M72.
Then indicator illuminates in front heated seat switch (driver side).
HIGH FUNCTION
When front heated seat switch (driver side) is in HIGH position, power is supplied
through front heated seat switch (driver side) terminal 3
to seat heater (driver side) terminals 54.
And, ground is supplied
to seat heater terminal 52
through grounds B16 and B17.
Then seat heater (driver side) HIGH function is activated.
At this time ground is supplied
to front heated seat switch (driver side) terminal 4
through grounds M71 and M72.
Then indicator illuminates in front heated seat switch (driver side).
