2003 MITSUBISHI SHOGUN brake

Cautions on handling of 4WD
vehicles
EI49A-Xa
Tyre and disc wheelsSince the driving torque can be applied to
the 4 wheels, the performance of the
vehicle when operating in 4WD is greatly
affected by the condition of the tyres.
Pay close attention to the tyres.
•Install specified tyres on all wheels. Refer
to“Tyre and wheels”on page 10-10.
•Be sure to equip the car with all four tyres
and wheels of the same size and type.
When replacement of any of the tyres or
wheels is necessary, replace all of them.
•All tyres should be rotated whenever the
wear difference between front and rear
tyres is recognizable.
Good vehicle performance cannot be
expected if there is a difference in wear
between tyres. Refer to the“Tyre rotation”
on page 9-15.
•Check the tyre inflation pressure regu-
larly.
CAUTION
Always use tyres of the same size,
same type, and same brand, which
have no wear differences.
Using the tyres of differ in size, type,
brand or a different degree of wear
will cause excessive loading, result-
ing in possible damage to the drive
system.Jacking up a 4-wheel drive vehicles
WARNING
Do not crank the engine while jack-
ing up the vehicle.
The tyre on the ground may turn and
the vehicle may roll off the jack.Operate clutch pedal slowly and
positivelyQuick or slight clutch engagement made
while the engine is running at high speed
will cause damage to the clutch and trans-
mission because the tractive force is very
great.
Operate the pedal slowly and positively.
I07A002A
1
Parking brake
EI07AAEd
To park the vehicle, first bring it to a com-
plete stop, fully engage the parking brake,
and then move the gearshift lever to 1st (on
an uphill) or Reverse (on a downhill) posi-
tion, for vehicles with a manual transmis-
sion or set the selector lever to“P”(PARK)
position on automatic transmission
vehicles.To apply1- Pull the lever up without pushing the
button at the end of the hand grip.
Starting and driving
5-42Div:
Out put date:

I07A049A
To release
1- Pull the lever up slightly.
2- Push the button at the end of the hand
grip.
3- Push the lever downward.
When parking on a hill, apply the parking
brake and turn the front wheels towards the
kerb on a downhill grade, away from the
kerb on an uphill grade.
CAUTION
Before driving, be sure that the park-
ing brake is fully released and the
brake warning lamp is off.
If a vehicle is driven without releas-
ing the parking brake, the brake will
be overheated, resulting in ineffec-
tive braking and possible brake fail-
ure.
Parking
EI22A-He
Parking on a slopeFully engage the parking brake, and then
move the gearshift lever to 1st (on an
uphill) or reverse (on a downhill) position on
manual transmission vehicle.
On automatic transmission vehicle, move
the selector lever to“P”(PARK) position.
When parking on a hill, apply chocks to
wheels for greater safety.Parking with the engine runningDo not keep the engine running in a closed
or poorly ventilated place. Carbon monox-
ide gas is odourless and extremely poison-
ous and dangerous.Where you parkDo not park in a place where there are
inflammable objects such as dry grass,
leaves, etc. because the exhaust system
produces very high temperatures. This may
cause a fire.When leaving the vehicleAlways remove the key from the ignition
switch and lock all doors when leaving the
vehicle unattended.
Always try to park your vehicle in a well lit
area.
Starting and driving
5-43
Div:
Out put date:

Braking
EI23AAGa
All the parts of the brake system are criti-
cal to safety. Have the vehicle serviced by an
authorized MITSUBISHI dealer at regular
intervals according to the service booklet.Brake system(1) The service brake is divided into two
brake circuits so that when one brake
circuit fails, the other is available to stop
the vehicle. If this occurs, however, the
brake pedal must be depressed fur-
ther than usual; stop driving as soon as
possible and have the brake system
repaired at the nearest authorized
MITSUBISHI dealer.
(2) The brake boosting force is lost after
the brake pedal is depressed once or
twice while the engine is off. If this
occurs, the brake will require greater
force than usual. This is especially
important when the vehicle is being
towed.
Vehicles equipped with anti-lock brake
system
The brake system uses brake fluid pres-
surized by the pump to power-assist the
brake. If the brake system fails during driv-
ing, the brake warning lamp comes on and
buzzer sounds continuously. In this case,
the brake may not work properly.If this buzzer should continue to sound,
park your vehicle in a safe place and con-
tact your nearest authorized MITSUB-
ISHI dealer.
Please refer to“Brake warning lamp”on
page 4-7.
CAUTION
Bring the vehicle to halt in a safe
location by applying the brakes gen-
tly. Applying the brakes rapidly or
driving at high speed may make the
vehicle unstable.
NOTE
(1) Depressing the brake pedal repeat-
edly may turn on the brake warning
lamp, ABS warning lamp and brake
warning buzzer. It is normal if the lamp
goes out and the buzzer stops sound-
ing after a few seconds.
(2) In certain cases immediately after the
engine has been started or when the
brake pedal is depressed repeatedly, a
noise generated by operation of brake
devices may be heard coming from the
engine compartment. This type of noise
is normal and is no need for concern.
In fact, it indicates that the correspond-
ing devices are operating normal.
Warning lampThe brake warning lamp lets you know if
your brake system is working properly.
Read“Brake warning lamp”on page 4-7.When brakes are wetCheck the brake system while driving at a
low speed immediately after starting, espe-
cially when the brakes are wet, to con-
firm they work normally.
A film of water can form on the brake discs
and prevent normal functioning after driv-
ing in heavy rain or through large puddles,
or after the vehicle is washed. If this occurs,
dry the brakes out by driving slowly while
lightly depressing the brake pedal.When driving downhillIt is important to take advantage of the
engine braking by shifting to a lower gear
while driving on steep downhill roads in
order to prevent the brakes from overheat-
ing.
Starting and driving
5-44Div:
Out put date:

Brake pads(1) With new brake pads, avoid where pos-
sible sudden full application of the
brakes for the first 200 km (125 miles)
of driving.
(2) The disc brakes are provided with a
warning device which emits a shriek-
ing metallic sound while braking if the
brake pads have reached their limit.
If you hear this sound, have the brake
pads replaced by your MITSUBISHI
dealer.
CAUTION
(1) Do not leave any objects or place
a thick floor mat around the
brake pedal; doing so could pre-
vent the full pedal stroke that
would be necessary in an emer-
gency. Make sure that the pedal
can be operated freely at all
times.
(2) Avoid driving habits that cause
heavy braking and never“ride”
the brakes by resting your foot
on the brake pedal while driv-
ing.
It causes brake overheating and
fade.
Anti - lock brake system (ABS)*
EI24ABCb
Environmental conditions can have an
effect on braking. During sudden braking
when there is snow, ice, oil, water etc. on
the road surface, a skid may occur. In this
situation, steering control and braking effec-
tiveness are reduced and the stopping dis-
tance is increased. The vehicle may also
go into an uncontrolled spin.
The ABS helps prevent the wheels from
locking during braking, thus maintaining
directional stability, ensuring controlabil-
ity and providing optimum braking force.Driving hints(1) With ABS fitted, steering during sud-
den braking (when the ABS functions)
differs slightly from when the brakes
are not being applied.
Steer the vehicle carefully in these con-
ditions.(2) Always maintain the same distance
from the vehicle in front of you as you
would for a vehicle not equipped with
ABS.
Compared with vehicles not fitted with
ABS, your vehicle may require a longer
stopping distance in the following
cases:
•Driving on gravel or snow-covered
roads.
•Driving with tyre chains installed.
•Driving on roads where the road sur-
face is pitted or has other differ-
ences in surface height.
•Driving on bumpy roads or other poor
driving surfaces.
(3) In order to ensure that the anti-lock
brake system (ABS) will operate cor-
rectly in situations where tyre chains
have been fitted, drive in“4H”or“4L”
for part time 4WD, or in“4H”,“4HLc”,
or“4LLc”for super select 4WD II.
(4) Operation of ABS is not restricted to
situations where brakes are applied
suddenly. This system may also oper-
ate to prevent wheel lock when you are
driving over manholes, steel road-work
plates, or the vehicle is driven over
steps or level differences in the road,
road markings, or other surfaces which
are difficult for the wheels to grip.
Starting and driving
5-45
Div:
Out put date:

(5) When the ABS system is activated, you
may feel the brake pedal pulsating and
hear a characteristic noise. Also at this
time, it may feel as if the pedal attempts
to resist being depressed.
In this situation, to let the ABS work
for you, just hold the brake pedal
down more firmly. Do not pump the
brake. This will result in reduced
braking performance.
CAUTION
(1)
Even the ABS can not prevent the
natural laws of physics from act-
ing on the vehicle. It cannot for
instance avoid accidents that may
result from excessive speed on
bends or following another vehicle
too closely or aquaplaning. It
should remain the driver’s task to
observe safety precautions to
judge speeds and brake applica-
tions correctly in such condi-
tions.
(2)
Be sure to use tyres of the same
type and size on four wheels.
If tyre types or sizes are mixed,
ABS may not function normally.
(3)
Never install a limited slip differ-
ential, which is not MITSUBISHI
Genuine parts, as the ABS may
not function normally.
Please consult an authorized
MITSUBISHI dealer.
I24A073A
Warning lampThe ABS warning lamp should illuminate
when the ignition switch is turned“ON”, and
should go off in a few seconds.
CAUTION
If the warning lamp stays on or does
not illuminate when you start the
vehicle, it indicates that the ABS is
not functioning and that only the
standard brake system is in opera-
tion. (In this condition the standard
hydraulic brake system will still
function.) Please contact your near-
est authorized MITSUBISHI dealer for
inspection.
Starting and driving
5-46Div:
Out put date:

NOTE
Depressing the brake pedal repeatedly may
turn on the brake warning lamp, ABS warn-
ing lamp and brake warning buzzer. It is
normal if the lamp goes out and the buzzer
stops sounding after a few seconds.
If the lamp illuminates while
driving(1) Since there will always be a possibil-
ity of the vehicle becoming unstable
when brakes are applied rapidly,
ensure that brakes are applied gently
and that high-speed driving is not
attempted; furthermore, bring the
vehicle to halt in a safe location.
Restart the engine and check to see
whether the lamp goes out after a few
minutes driving; if it then remains off
during driving, there is no problem.
However, if the lamp does not go out,
or if it lights up again when the vehicle
is driven, have the vehicle checked by
an authorized MITSUBISHI dealer as
soon as possible.
(2) After starting the engine using jumper
cables, if you attempt to drive the
vehicle before the battery is suffi-
ciently charged, the engine will run
irregularly and the ABS warning lamp
will illuminate indicating that the vehicle
should not be driven.
This situation, however, is caused
merely by insufficient battery voltage
and is not an abnormal situation.
If such a situation occurs, run the
engine at idle for some time to charge
the battery.
I24A119A
FrontNOTE
(1) Immediately after the vehicle starts
moving after engine start up, a brake
pedal pulsating is felt when the brake
pedal is depressed. This pulsation is
due to the self-diagnosis operation of
the ABS and does not indicate a mal-
function.
(2) After driving on snowy roads, remove
any snow and ice which may have
become adhered to the wheel areas.
When doing this, be careful not to dam-
age the wheel speed sensors (A) and
cables located at each wheel on
vehicles equipped with an ABS.
Starting and driving
5-47
Div:
Out put date:

I10A126A
Auto-speed (cruise) control*
EI10AAOa
Auto-speed (cruise) control is an auto-
matic speed control system. It lets you keep
the same driving speed; auto-speed con-
trol can be used at 40 km/h (25 mph) or
more. It is especially useful for high way
driving. Auto-speed control does not work
at speeds below about 40 km/h (25 mph).
A - Main switch
B - Auto-speed control lever
CAUTION
(1) For safety reasons, the main
switch (A) should be set to the
“OFF”position when you are not
using the auto-speed control
system.
(2) Auto-speed control is not rec-
ommended when driving condi-
tions will not allow you to stay at
the same speed, such as in
heavy traffic or on roads that are
winding, icy, snow-covered, wet,
or slippery, or on a steep down-
hill.
(3) For vehicles with manual trans-
mission, if you shift to“N”
(NEUTRAL) in auto-speed con-
trol mode without pressing the
clutch first, the engine will run
too fast and might be dam-
aged.NOTE
(1) Auto-speed control may not be able to
keep your speed on uphills or down-
hills.
(2) Your speed may drop on a steep uphill.
You must use the accelerator if you
want to stay at your set speed.
(3) Your speed may increase to more than
the set speed on a steep downhill. You
must use the brake to control your
speed. If your speed increases too
much, turn off the auto-speed control.
(Refer to the section“To deactivate”on
page 5-56.)
Starting and driving
5-53
Div:
Out put date:

I10A128A
Brake pedal
Use the brake pedal and then pull the
auto-speed control lever down.
I10A121A
To accelerate for passingPress the accelerator pedal as you would
normally. When you release the pedal, you
will return to your set speed.
I10A151A
To deactivateThe auto-speed control can be deacti-
vated as follows:
(1) Push the main switch (A) at the end of
the lever. (Main switch OFF)
(2) Pull the auto-speed control lever (B)
towards you.
The auto-speed control can be turned off
automatically in any of the following ways.
(3) By slightly tapping the brake pedal or
pressing it to reduce the speed.
(4) By pressing the clutch pedal (for
vehicles with manual transmission).
(5) By moving the selector lever to“N”
(NEUTRAL) (for vehicles with auto-
matic transmission).
Starting and driving
5-56Div:
Out put date: