2003 MERCEDES-BENZ SLK32AMG start stop button

47 Getting started
Parking and locking
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.
Parking brake
1Brake lever
2Release button
Pull up brake lever1 firmly.
When the engine is running, the indica-
tor lamp
;
(USA only) or
3
(Canada only) in the instrument cluster
will be illuminated.
Warning!
G
Wait until the vehicle is stationary before re-
moving the key from the starter switch. The
vehicle cannot be steered when the key is
removed.Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
system. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to stop or steer the vehi-
cle.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before turning off
the engine and leaving the vehicle always:

Keep right foot on brake pedal.


Pull up the brake lever firmly.


Move the selector lever to positionP
(manual transmission: first or reverse
gear).


Slowly release brake pedal.


When parked on an incline, turn front
wheels towards the road curb.


Turn the key to steering lock position0
and remove.

120 Controls in detailAudio systemFast forward/reverse
Press the
d
button.
FORWARD
will appear on the display and
fast forward will start.

Press the
c
button.
REWIND
will appear on the display and
fast reverse will start.

Press the same button again to stop
fast forward/reverse, or it will stop au-
tomatically at the beginning or the end
of the tape. The track will automatically
change at the end or beginning of the
tape and play will begin.Scanning

Press the
SC key.
Each track on the cassette will be
played for 8 seconds in ascending or-
der.Dolby NR
1 (noise reduction system)
To enable optimum reproduction of cas-
settes recorded using the Dolby B system,
press the AUD
key followed by the
NR key.
NR is shown in the display in inversed-color
format. To turn off Dolby B noise reduc-
tion, press the
NR key again. The
NR in the
display will be shown in the original color
format.
iThe beginning of a track can only be lo-
cated if there is a break of at least
4 seconds between tracks.
Scan will be interrupted if the
d
,
c
, f
, e
buttons or the
SC
key is pressed.
1Dolby and the double-D symbol
Ù
are trade-
marks of Dolby Laboratories Licensing Corpora-
tion. The Dolby noise reduction system is
manufactured under license from Dolby Laborato-
ries Licensing Corporation.

122 Controls in detailAudio systemCD changer* installed
1CD
2CD changer
3CD tray
4CD magazine
If a CD changer is installed, it can be oper-
ated from the front control panel of the ra-
dio. A loaded magazine must be installed
for CD playing.Loading/unloading the CD magazine

Slide the changer door to the right.

Press the eject button
d
.
The magazine will be ejected.

Remove the magazine.

Pull out the CD tray until its stop is
reached.

Place the CDs in the recess of the tray,
label side up.

Push the tray into the magazine in the
direction shown by the arrow.

Insert the loaded magazine into the
changer.Playing CDs

Press the CD button.
The CD most recently played will start
at the point where it was last switched
off. CDs stored in the magazine can be
selected by using the station preset
buttons 1-6.
The magazine slot number of the selected
CD will then be displayed after
CD. The
number of the track being played will be
displayed after
TRACK
.
If there is no CD in the selected magazine
slot,
NO CD
and the corresponding slot
number will be displayed (e.g.
NO CD3
). Af-
ter the last track on a CD has been played,
the next CD will automatically be selected
and played.
!Close the door after the magazine has
been inserted.

123 Controls in detail
Audio system
Skipping tracks forwards / backwards
Press the
f
button.
The next track on the CD will be played.

Press the
e
button.
If the track has been playing for more
than 10 seconds, it will revert to the
start of that track. If it has been playing
for less than 10 seconds, it will revert
to the preceding track.
To skip several tracks, the respective
button must be pressed until the de-
sired track is reached. If the beginning
or end of the CD is reached during the
search, the first or last track will be
played.Fast forward/reverse

Press the
d
button and hold it down
for audible fast forward.

Press the
c
button and hold it down
for audible reverse.
The search will stop when the button is re-
leased. The relative time of the track will
be displayed during the search. The search
mode will cancel if the beginning or end of
the CD is reached.
Scanning

Press the
SC key.
Each track will be played for 8 seconds
in ascending order.
The search will stop at the track in
question if the d
, c
, f
, e

buttons or the
SC key are pressed.Random play/repeat function
The tracks of the current CD are played in
random order when the random feature
(
RDM
) is selected.

Press the
RDM
key to switch on, and
press
RDM
again to switch off.
When the repeat function (
RPT
) has been
selected, a particular track can be played
for as many times as desired.

Press the
RPT
key to switch on.

Press
RPT
again to switch off.
iBoth functions cannot be used simulta-
neously.

150 Controls in detailUseful features
Upgrade signals
The Tele Aid system processes calls using
the following priority.

Automatic emergency – First priority


Manual emergency – Second priority


Roadside assistance – Third priority


Information – Fourth priority
Should a higher priority call be initiated
while you are connected, an upgrade (al-
ternating) tone will be heard, and the ap-
propriate indicator lamp will flash. If
certain information such as vehicle identi-
fication number or customer information is
not available, the operator may need to re-
transmit.During this time you will hear a beep and
voice contact will be interrupted. Voice
contact will resume once the retransmis-
sion is completed. Once a call is conclud-
ed, a beep will be heard and the
appropriate indicator lamp will stop flash-
ing. Audio system operation will resume.
!If the indicator lamps do not start flash-
ing after pressing one of the buttons or
remain illuminated (in red) at any time,
the Tele Aid system has detected a
fault or the service is not currently ac-
tive, and may not initiate a call. Visit
your Mercedes-Benz Center and have
the system checked or contact the Re-
sponse Center at 1-800-756-9018 (in
the USA) or 1-888-923-8367 (in
Canada) as soon as possible.
!If the indicator lamp continues to flash
or the system does not reset, contact
the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or
Mercedes-Benz Customer Assistance
at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or Cus-
tomer Service at 1-800-387-0100 in
Canada.