246 Controls in detailUseful featuresProgramming or reprogramming the in-
tegrated remote control
Turn SmartKey in the starter switch to
position1 or2.
Hold the end of the hand-held transmit-
ter of the device you wish to train
approximately 2 to 5 inches (5 cm to
12 cm) away from the surface of the in-
tegrated remote control located on the
inside rear view mirror, keeping the in-
dicator lamp in view.
Using both hands, simultaneously push
the hand-held transmitter button and
the desired integrated remote control
button. Do not release the buttons until
completing next step.
The indicator lamp on the integrated re-
mote control will flash, first slowly and
then rapidly. The rapid flashing lamp indi-
cates successful programming of the new
frequency signal.
When the indicator lamp flashes rapid-
ly, release both buttons.
To program the remaining two buttons,
repeat the above steps.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion of
this text. (A second person may make the
following training procedures quicker and
easier.)
Locate training button on the garage
door opener motor head unit. Exact location and color of the button
may vary by garage door opener brand.
If there is difficulty locating the trans-
mitting button, refer to garage door
opener operator’s manual.
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Firmly press and release the pro-
grammed integrated remote control
transmit button.
Press and release same button a sec-
ond time to complete the training pro-
cess.
Some garage door openers may require
you to do this procedure a third time to
complete the training.
Confirm the garage door operation by
pressing the programmed button on
the integrated remote control transmit-
ter.
iIf, after several attempts, you do not
successfully program the integrated re-
mote control device to learn the signal
of the hand-held transmitter, the ga-
rage door opener could be equipped
with the “rolling code feature.”
402 Index
Selecting stations 136
Station search 136
Station selection setting 154
Radio transmitters, control and operation
258
Range (distance to empty)
Calling up 145
Rear fog lamp 332
Bulb 332
Switching on 123
Rear lamp bulbs
Replacing 336
Rear lamps see Tail lamps
Rear passenger compartment
Adjustable air vents 186
Rear seat head restraints
Folding back with switch 106
Placing upright 106
Rear seats 106
Rear seats 113
Fore and aft adjustment 114
Head restraint folding 114
Individual seats* 114
Passenger seat fore and aft adjustment
116
Passenger seat head restraint height 116
Passenger seat height 116
Rear seat head restraints 106
Seat height 114
Setting passenger seat position from
rear* 115
Rear view mirror 27
Rear view mirror automatic antiglare 168
Rear view mirrors see Mirrors
Rear window
Blocking operation 74
Rear window defroster 183
Activating 183
Deactivating 183
Rear window sunshade* 173
Reconnecting
Vehicle battery 345
Regular checks 262
Regular driving style 214
Reinstalling vehicle battery 345
Remote controls
Integrated 246
SmartKey 86
Remote door unlock
With Tele Aid* 244
Remote Vehicle Diagnostics 384Removing
Vehicle battery 345
Wheel 341
Wiper blades 337
Replacing
Backup lamp bulbs 336
Brake fluid 373
Brake lamp bulbs 336
Bulbs 331
Front lamp bulbs 333
License plate lamp bulbs 336
Parking lamp bulbs 335
Rear fog lamp bulbs 336
Rear lamp bulbs 332, 336
Rear turn signal bulbs 336
Side marker lamp bulbs 335
Standing lamp bulbs 335
Wiper blades 337
Reporting
Safety defects 18
Reset knob in the instrument cluster 146
Resetting
All functions (control system) 146
All functions of a submenu 147
Fuel consumption 144
Service indicator (FSS) 281
