Page 226 of 321
226 Practical hintsWhat to do if …¿
The yellow malfunction indicator
lamp comes on while driving.
The BAS or ESP is malfunctioning.
It is possible that the engine output will be re-
duced.
Have the BAS/ESP checked at an au-
thorized Mercedes-Benz Light Truck
Center as soon as possible.
{
The yellow malfunction indicator
lamp comes on while driving.
4-ETS has switched off to prevent overheat-
ing of the brakes. Also see 4-ETS/ESP warn-
ing lamp (
page 224).
As soon as the brakes have cooled off,
4-ETS switches on again.
The indicator lamp goes out.
4-ETS is malfunctioning and has switched off.
Have the 4-ETS checked at your au-
thorized Mercedes-Benz Light Truck
Center as soon as possible.
ê
The yellow LOW RANGE indicator
lamp blinks after one or more
switching conditions.
The gear selection conditions have not been
adhered to.
Repeat the gear selection process
(page 118).
ê
The yellow LOW RANGE indicator
lamp blinks after switching the
ignition on.
LOW RANGE mode is malfunctioning.
Have the LOW RANGE mode checked at
your authorized Mercedes-Benz Light
Truck Center.
Problem
Possible cause
Suggested solution
Page 228 of 321
228 Practical hintsWhat to do if …Problem
Possible cause
Suggested solution
É
The red brake warning lamp
lights up while driving and you
hear a warning sound.
You are driving with the parking brake set.
Release the parking brake
(page 45).
É
The red brake warning lamp
lights up while driving.
There is insufficient brake fluid in the reser-
voir.
Risk of accident! Carefully stop the
vehicle and notify an authorized
Mercedes-Benz Light Truck Center.
Do not add brake fluid! This will not
solve the problem.
Warning!
G
Driving with the brake warning lamp illumi-
nated can result in an accident. Have your
brake system checked immediately if the
brake warning lamp stays on. Don’t add
brake fluid before checking the brake sys-
tem. Overfilling the brake fluid reservoir can
result in spilling brake fluid on hot engine
parts and the brake fluid catching fire. You
can be seriously burned.
!If you find that the brake fluid in the
brake fluid reservoir has fallen to the
minimum mark or below, have the
brake system checked for brake pad
thickness and leaks.
Page 229 of 321
229 Practical hints
What to do if …
Problem
Possible cause
Suggested solution
É
-
The red brake warning lamp
lights up in addition to the yellow
ABS malfunction lamp and you
hear a warning sound.
There is a malfunction in the Electronic Brake
Proportioning (EBP) system.
The enhanced braking effect is not available.
Have the system checked immediate-
ly at an authorized Mercedes-Benz
Light Truck Center.
Failure to follow these instructions in-
creases the risk of accidents.
:
The yellow warning lamp blinks
after starting the engine or while
driving.
The engine oil level has sunk to the minimum
level. If the engine oil level continues to sink,
the warning lamp will light up.
Add approved oil at the next gas sta-
tion (
page 286).
If oil loss is visible on the engine, have
the malfunction corrected as soon as
possible at a Mercedes-Benz Light
Truck Center.
_
The red indicator lamp does not
go out after starting the engine.
The adjustable telescoping steering column
is not properly locked.
Lock the adjustable steering column
(page 37).
‡
The green front fog lamp indica-
tor lamp lights up when ignition
is turned on.
The front fog lamps are switched on.
Fog lamps (
page 105).
Page 232 of 321
232 Practical hintsWhat to do if …Problem
Possible cause
Suggested solution
?
The yellow “CHECK ENGINE”
malfunction indicator lamp
comes on while driving.
There is a malfunction of:
The fuel management system
The ignition system
The emission control system
Systems which affect emissions
Such malfunctions may result in excessive
emissions values and may switch the engine
to its limp-home (emergency operation)
mode.
Have the vehicle checked as soon as
possible by an authorized
Mercedes-Benz Light Truck Center.
An on-board diagnostic connector is
used by the service station to link the
vehicle to the shop diagnostics sys-
tem. It allows the accurate identifica-
tion of system malfunctions through
the readout of diagnostic trouble
codes. It is located in the front left
area of the footwell next to the park-
ing brake pedal.
The fuel cap is not closed tightly.
Check the fuel cap (
page 200).
Your fuel tank is empty.
After refuelling start the engine three
or four times in succession.
The limp-home mode is canceled. You do
not need to have your vehicle checked.
7
The indicator lamp lights up.
A BabySmart
TM child seat is installed on the
front passenger seat. The front passenger
airbag is therefore switched off.
The system is malfunctioning when there is
no BabySmart
TM child seat installed on the
front passenger seat.
Have the system checked as soon as
possible by an authorized
Mercedes-Benz Light Truck Center.
Page 234 of 321
234 Practical hintsWhat to do if …<
The red seat belt warning lamp
blinks for a brief period after
starting the engine.
The warning lamp reminds you to fasten seat
belts.
Fasten your seat belt (
page 60).
W
The yellow low washer system
fluid level lamp lights up after
starting the engine or while driv-
ing.
There is approximately 1.3 US qt. (1.25 l) of
washer fluid remaining in the reservoir.
Add washer fluid (
page 208).
The washer fluid may have frozen
Move the vehicle to a warmer environ-
ment so that the washer fluid will
thaw.
Correct the concentration level after
the washer fluid in the reservoir
thaws.
2
The yellow brake indicator lamp
lights up during braking or after
starting the engine.
The brake pads are worn down.
Have the system checked at an autho-
rized Mercedes-Benz Light Truck
Center.
Problem
Possible cause
Suggested solution
!Brake pad thickness must be visually
checked by a qualified technician at the
intervals specified in the Service book-
let.
Page 248 of 321
248 Practical hintsReplacing bulbsRear lamps Notes on bulb replacement
Use only 12-volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Light Truck Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Light Truck Center:
Additional turn signals in the exteri-
or rear view mirrors
Bi-Xenon lamps*
Front fog lamps (vehicles with sport
package)*
Lamp
Type
6
Brake lamp
1073
(32 cp bulb)
7
Backup lamp
1073
(32 cp bulb)
8
Turn signal lamp
PY 21 W
9
Tail, parking and
standing lamp
Rear fog lamp, driv-
er’s side
P 21/4 W
10
Side marker lamp
W5W
11
High mounted brake
lamp
1073
(32 cp bulb)
12
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
Page 251 of 321
251 Practical hints
Replacing bulbs
Align headlamp cover and click into
place.
Fog lamp bulbs
1Fog lamp
Switch off the lights.
Use a suitable object (e.g. screwdriver)
to press on the release lever behind the
front panel.
Front fog lamp1 releases.
Remove fog lamp out of bumper.2Bulb socket
3Tabs
Twist bulb socket2 counterclockwise
to its end stop and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket2.
Twist bulb socket2 clockwise to its
end stop.
Reinstall fog lamp into the bumper.
Make sure that tabs3 firmly seat into
the slots of holder.
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off the lights.
Open liftgate.
1Screws
2Tail, parking and standing lamp
Fog lamp, driver’s side
3Side marker lamp
4Turn signal lamp
5Backup lamp
6Brake lamp
Remove screws1.
Remove tail lamp.
Page 252 of 321
252 Practical hintsReplacing bulbs7Tabs
Squeeze tabs7 together and remove
bulb holder.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
turn clockwise.
Reinstall bulb holder. You should hear
it engage.
Insert the tail lamp in the body, lower
edge first. Make sure that it engages.
Retighten screws with washers on
them.License plate lamp
1License plate lamp
2Screws
Switch off the lights.
Loosen both screws1 and remove
lamp.
Replace the tubular lamp and reinstall
lamp.
Retighten the screws.High mounted brake lamp
1Cover
2Tab
Switch off the lights.
Squeeze both sides of cover1, fold it
forward and remove.
Press tab2 on reflector and remove re-
flector.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
turn clockwise.
