Page 232 of 321
232 Practical hintsWhat to do if …Problem
Possible cause
Suggested solution
?
The yellow “CHECK ENGINE”
malfunction indicator lamp
comes on while driving.
There is a malfunction of:
The fuel management system
The ignition system
The emission control system
Systems which affect emissions
Such malfunctions may result in excessive
emissions values and may switch the engine
to its limp-home (emergency operation)
mode.
Have the vehicle checked as soon as
possible by an authorized
Mercedes-Benz Light Truck Center.
An on-board diagnostic connector is
used by the service station to link the
vehicle to the shop diagnostics sys-
tem. It allows the accurate identifica-
tion of system malfunctions through
the readout of diagnostic trouble
codes. It is located in the front left
area of the footwell next to the park-
ing brake pedal.
The fuel cap is not closed tightly.
Check the fuel cap (
page 200).
Your fuel tank is empty.
After refuelling start the engine three
or four times in succession.
The limp-home mode is canceled. You do
not need to have your vehicle checked.
7
The indicator lamp lights up.
A BabySmart
TM child seat is installed on the
front passenger seat. The front passenger
airbag is therefore switched off.
The system is malfunctioning when there is
no BabySmart
TM child seat installed on the
front passenger seat.
Have the system checked as soon as
possible by an authorized
Mercedes-Benz Light Truck Center.
Page 233 of 321
233 Practical hints
What to do if …
7
The indicator lamp does not light
up with a BabySmart
TM child
seat properly installed on the
front passenger seat.
The system is malfunctioning.
Make sure that there is nothing be-
tween seat cushion and child seat and
check installation of the child seat
(page 63).
If the light remains out, have the sys-
tem checked as soon as possible by
an authorized Mercedes-Benz Light
Truck Center.
Do not use the BabySmart
TM restraint
to transport children on the front pas-
senger seat until the system has been
repaired.
The yellow fuel tank reserve
warning lamp lights up while
driving.
The fuel level has gone below the reserve
mark.
Refuel at the next gas station
(page 200).
#
The red charge indicator lamp
lights up when the engine is run-
ning.
The battery is no longer charging.
Possible causes:
alternator malfunctioning
broken poly-V-belt
Stop immediately and check the
poly-V-belt.
If it is broken
Do not continue to drive, before the
poly-V-belt is replaced.
Notify an authorized Mercedes-Benz
Light Truck Center.
Problem
Possible cause
Suggested solution
Page 234 of 321
234 Practical hintsWhat to do if …<
The red seat belt warning lamp
blinks for a brief period after
starting the engine.
The warning lamp reminds you to fasten seat
belts.
Fasten your seat belt (
page 60).
W
The yellow low washer system
fluid level lamp lights up after
starting the engine or while driv-
ing.
There is approximately 1.3 US qt. (1.25 l) of
washer fluid remaining in the reservoir.
Add washer fluid (
page 208).
The washer fluid may have frozen
Move the vehicle to a warmer environ-
ment so that the washer fluid will
thaw.
Correct the concentration level after
the washer fluid in the reservoir
thaws.
2
The yellow brake indicator lamp
lights up during braking or after
starting the engine.
The brake pads are worn down.
Have the system checked at an autho-
rized Mercedes-Benz Light Truck
Center.
Problem
Possible cause
Suggested solution
!Brake pad thickness must be visually
checked by a qualified technician at the
intervals specified in the Service book-
let.
Page 235 of 321
235 Practical hints
What to do if …
Additional indicators in the speedome-ter displayDisplay
Possible cause
Suggested solution
9
Perform minor service (A) (
page 215).
Visit an authorized Mercedes-Benz
Center to perform service.
´
Perform major service (B) (
page 215).
Visit an authorized Mercedes-Benz
Center to perform service.
Á
î
The
StArt
message lights up in
addition to the
Error
message.
The immobilizer is not operational.
Contact an authorized
Mercedes-Benz Center or call
1-800-FOR-MERCedes (in the USA),
or 1-800-387-0100 (in Canada).
Page 248 of 321
248 Practical hintsReplacing bulbsRear lamps Notes on bulb replacement
Use only 12-volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Light Truck Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Light Truck Center:
Additional turn signals in the exteri-
or rear view mirrors
Bi-Xenon lamps*
Front fog lamps (vehicles with sport
package)*
Lamp
Type
6
Brake lamp
1073
(32 cp bulb)
7
Backup lamp
1073
(32 cp bulb)
8
Turn signal lamp
PY 21 W
9
Tail, parking and
standing lamp
Rear fog lamp, driv-
er’s side
P 21/4 W
10
Side marker lamp
W5W
11
High mounted brake
lamp
1073
(32 cp bulb)
12
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
Page 249 of 321
249 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Replacing low beam bulbs
1Low beam halogen or Bi-Xenon* head-
lamp cover with locking tab2Electrical connector
Bi-Xenon* headlampHalogen headlamp
Switch off the lights.
Open the hood (
page 202).
Push down tab at top end of cover1
and remove.
Pull electrical connector2 off.
Unclip the retainer springs and take out
the bulb.
Insert the new bulb so that the base lo-
cates in the recess on the holder.
Clip the retainer springs.
Plug the connector2 onto the bulb.
Align headlamp cover and click into
place.
Warning!
G
Do not remove the cover1 for the Bi-Xenon
headlamp. Because of high voltage in xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
o mme n d th at y o u h av e s uc h wo rk don e by a
qualified technician.
Page 250 of 321
250 Practical hintsReplacing bulbsHigh beam bulbs
1High beam headlamp cover with lock-
ing tab
Switch off the lights.
Open the hood (
page 202).
Twist cover1 counterclockwise and re-
move.2Electrical connector
Pull electrical connector2 off.
Unclip the retainer springs and take out
the bulb.
Insert the new bulb so that the base lo-
cates in the recess on the holder.
Clip the retainer springs.
Plug the connector2 onto the bulb.
Align headlamp cover and click into
place.Turn signal, parking, standing and side
marker lamp bulbs
1Bulb socket
Switch off the lights.
Open the hood (
page 202).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall the bulb socket.
Page 251 of 321
251 Practical hints
Replacing bulbs
Align headlamp cover and click into
place.
Fog lamp bulbs
1Fog lamp
Switch off the lights.
Use a suitable object (e.g. screwdriver)
to press on the release lever behind the
front panel.
Front fog lamp1 releases.
Remove fog lamp out of bumper.2Bulb socket
3Tabs
Twist bulb socket2 counterclockwise
to its end stop and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket2.
Twist bulb socket2 clockwise to its
end stop.
Reinstall fog lamp into the bumper.
Make sure that tabs3 firmly seat into
the slots of holder.
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off the lights.
Open liftgate.
1Screws
2Tail, parking and standing lamp
Fog lamp, driver’s side
3Side marker lamp
4Turn signal lamp
5Backup lamp
6Brake lamp
Remove screws1.
Remove tail lamp.
