Page 333 of 399
333 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement
Use only 12-volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Y o u r h a n d s s h o u l d b e d r y a n d f r e e o f o i l
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center:
Additional turn signal lamps in the
exterior rear view mirrors
High mounted brake lamp
Bi-Xenon lamps
Front fog lamps
Lamp
Type
7
High mounted brake
lamp
LED
8
Tail, parking and
standing lamp
HiP
9
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
Page 334 of 399
334 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Bulb socket for turn signal lamp
2High beam bulb
3Bulb socket for parking and standing
lamp
High beam bulb (Halogen headlamps
only)
Switch off the lights.
Open the hood (
page 261).
Press the clamp and remove headlamp
cover.
Pull electrical connector off.
Turn the locking mechanism counter-
clockwise and take out the high beam
bulb2.
Insert the new high beam bulb so that
the base is in the recess of the holder.
Turn the locking mechanism clockwise.
Plug the connector onto the high beam
bulb.
Align headlamp cover and click into
place.
High beam bulb (Bi-Xenon* headlamps
only)
Switch off the lights.
Open the hood (
page 261).
Press the clamp and remove headlamp
cover.
Pull electrical connector off.
Turn the locking mechanism counter-
clockwise and take out the high beam
bulb2.
Insert the new high beam bulb so that
the base is in the recess of the holder.
Turn the locking mechanism clockwise.
Plug the connector onto the high beam
bulb.
Align headlamp cover and click into
place.
Warning!
G
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
Page 335 of 399
335 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 261).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 261).
Press the clamp and remove headlamp
cover.
Pull out the bulb socket3 with the
bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align headlamp cover and click into
place.Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards front.
Remove rear end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Page 349 of 399
349 Practical hints
Towing the vehicle
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:
the engine will not run
there is a malfunction in the SBC brake
system
there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the key is in
starter switch position2.
If the key is left in the starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock, re-
move key from starter switch and reinsert.
iTo signal turns while being towed with
the hazard warning flasher in use, turn
key in starter switch to position2 and
activate the combination switch for the
left or right turn signal in the usual
manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the haz-
ard warning flasher will operate again.
Warning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its
limp-home (emergency operation) mode. To
brake, the driver must then apply signifi-
cantly greater brake pedal pressure and de-
press the pedal much further to obtain the
expected braking effect. If necessary, apply
full pressure to the brake pedal. Brakes are
only applied to the front wheels. Stopping
distance is increased! Adapt your driving
style accordingly. SBC brake system
(page 77).
With the engine not running, there is no
power assistance for the steering system. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to steer the vehicle. Adapt your driv-
ing accordingly.
Page 384 of 399
384 IndexClock 137
Closing
Glove box 226
Side windows 184
Side windows with KEYLESS-GO* 92
Sliding/pop-up roof* 187
Sliding/pop-up roof* with
KEYLESS-GO* 92
Sliding/pop-up roof* with
SmartKey 188, 192
Trunk lid 96
Windows 184
Windows with SmartKey 185
Cockpit 20, 375
COMAND* see separate operating instruc-
tions
Combination switch 115
High beam flasher 47
Turn signals 46
Windshield wipers 47
Consumer information 373
Control system 121, 376
AUDIO menu 126
Convenience submenu 143
Display digital speedometer 126
Distronic* menu 128Functions 125
Instrument cluster submenu 134,
136
Lighting submenu 138
Malfunction memory menu 129
Menus 124, 125, 378
Multifunction display 121
Multifunction steering wheel 122
Selecting radio system 127
Settings menu 130
Standard display menu 126
Submenus 123, 125
TEL* menu 147
Trip computer menu 145
Vehicle submenu 142
Convenience submenu 143
Activating easy-entry/exit
feature* 143
Setting key dependency 144
Setting parking position for exterior
rear view mirror 144
Coolant
Messages in display 311, 312
Temperature display 119
Warning lamp 292, 311
Cruise control 194, 376Canceling 195
Driving downhill 195
Driving uphill 195
Fine adjustment 196
Lever 201
Saving current speed 195
Setting speeds 196
Cruise control lever 194
Customer Assistance Center (CAC) 375
D
Daytime running lamp mode 114
Setting 139
Deactivating
Air conditioner 170
Air recirculation mode 168, 179, 180
Alarm 82
Anti-theft alarm system 82
Automatic climate control 169, 174
Central locking (control system) 142
Climate control 164
Cruise control 195
Defrost 167, 178
Distance warning function* 206
Distronic* 204
Engine with KEYLESS-GO* 53
Engine with the key 52
Page 397 of 399
397 Index
Dialing a number from the phone
book 149
Ending a call 149
Loading phone book* 149
Messages in display 309
Operating 147
Redialing 149
Temperature
Display mode 134
Sensor 27
Setting interior temperature 165,
176
Setting units in display 134
Tie-down rings (trunk) 225
Tightening torque 342, 379
Time
Setting hours 137
Setting minutes 137, 138
Tire inflation pressure
Setting units 136
Tire speed rating 379
Tires 373
Tools 326
Tow-away alarm 82
Arming 82
Disarming 82Disarming for transport 82
Towing eye bolt (vehicle tool kit)
Installing 350
Towing the vehicle 348
Tracking services
For stolen vehicle 242
Traction 155, 379
Trip computer 145
Trip odometer
Resetting 119
Trunk
Closing the lid 96
Lamp 117
Lock button, KEYLESS-GO* 92
Message in display 310
Opening 88, 96
Opening from inside vehicle 94
Separately locking 98
Tie-down rings 225
Trunk lid emergency release 97
Unlocking with KEYLESS-GO* 92
Trunk lid
Closing 96
Turn signals 46
Additional in mirrors 332
Front bulbs 332Turning off
Engine 51
U
Units
Setting speedometer units 134
Setting temperature units 134
Setting tire inflation pressure
units 136
Unlocking 30, 86, 327
Centrally from inside 100
Driver’s door in an emergency 327
Fuel filler flap 259
Global 87
Global with KEYLESS-GO* 91
Selective settings 87
Trunk lid with KEYLESS-GO* 92
Vehicle in an emergency 241
With KEYLESS-GO* 32
With the SmartKey 30
Upgrade signals
Tele Aid* 240
Uphill driving
Cruise control 195
Upshifting 152
Useful features 226
Ashtrays 231
