Page 309 of 394
309 Practical hints
Where will I find...?
In the case of a flat tire, you may tempo-
rarily use the Minispare wheel when ob-
serving the following restrictions:
Do not exceed a vehicle speed of
50 mph (80 km/h).
Drive to the nearest tire repair facility
to have the flat tire repaired or re-
placed as appropriate.
Do not operate vehicle with more than
one Minispare wheel mounted.
More information can be found in the
“Technical data” section (
page 345).Minispare wheel bolts
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel or other
steel rims
!Wheel bolts2 must be used when
mounting the Minispare wheel. The use
of any wheel bolts other than wheel
bolts 2 for the Minispare will physically
damage the vehicle's brakes.
Warning!
G
Be sure to use the original length wheel
bolts when remounting the original wheel af-
ter it has been repaired.
Page 314 of 394
314 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencySliding/pop-up roof
The sliding/pop-up roof drive is located
behind the lens of the interior overhead
light.
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
Pry off lens1 using a flat blade screw-
driver.
Slide both locking tabs2 in direction of
arrow.
Lower rear of cover and remove.
Remove cover.iDo not disconnect electrical connec-
tors.
Page 316 of 394
316 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
Bulbs
iIf the headlamps are fogged up on the
inside as a result of high humidity, driv-
ing the vehicle a distance should clear
up the fogging.
iBackup bulbs will be brought into use
when the following lamps malfunction:
Turn signal lamps
Brake lamps
Parking lamps
Tail lamps
Page 318 of 394
318 Practical hintsReplacing bulbs
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signal lamps in the
exterior rear view mirrors
High mounted brake lamp
Bi-Xenon* lamps
Front fog lamps
Replacing bulbs for front lamps
Front lamps halogen-type
1Housing cover for low beam lamp
2Housing cover for high beam lamp3Bulb socket for turn signal lamp
4Low beam bulb
5High beam bulb
6Parking and standing lamp
Page 319 of 394
319 Practical hints
Replacing bulbs
Low beam and high beam bulb
Switch off the lights.
Open the hood (
page 253).
Turn housing cover1 or 2 counter-
clockwise and remove.
Turn bulb holder 4 or 5 with the bulb
counterclockwise and remove.
Press the bulb backwards and turn
counterclockwise out of the bulb hold-
er.
Press the new bulb into the holder and
twist it clockwise.
Place the bulb holder back into the
lamp and turn it clockwise.
Place the corresponding housing cov-
ers back on and turn them clockwise.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 253).
Twist bulb socket3 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 253).
Turn housing cover2 counterclockwise
and remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.
Page 320 of 394
320 Practical hintsReplacing bulbsFront lamps Bi-Xenon*-type
1Bulb socket for turn signal lamp
2Housing cover for high beam lamp
3Housing cover for Bi-Xenon* lamp4High beam bulb
5Parking and standing lampHigh beam bulb
Switch off the lights.
Open the hood (
page 253).
Turn housing cover2 counterclockwise
and remove.
Turn bulb holder 4 with the bulb coun-
terclockwise and remove.
Press the bulb backwards and turn
counterclockwise out of the bulb hold-
er.
Press the new bulb into the holder and
twist it clockwise.
Place the bulb holder back into the
lamp and turn it clockwise.
Place the housing cover 2 back on and
turn them clockwise.
Warning!
G
Do not remove the cover 3 for the Bi-Xenon*
headlamp. Because of high voltage in xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
o mme nd t h at y ou ha ve s uc h w o rk do n e by a
qualified technician.
Page 321 of 394
321 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 253).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 253).
Turn housing cover2 counterclockwise
and remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.
Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Page 322 of 394
322 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Tail lamp assemblies
1Brake lamp
2Turn signal lamp
3Backup lamp
4Standing and side marker lamp
5Rear fog lamp (driver’s side)/tail
Switch off the lights.
Open trunk.
Swing the trim panel covering the cor-
responding rear lights to the side.
Squeeze tabs together and remove the
bulb holder with the bulb.
Twist bulb counterclockwise and pull
out of bulb holder.
Insert new bulb into the holder and turn
it clockwise.
Reinstall bulb holder. The tabs must au-
dibly click.
Close trim panel.
Place the housing cover back on so
that its tabs click in place. License plate lamp
1Screws
Switch off the lights.
Loosen both screws1 and remove
lamp.
Replace the tubular lamp and reinstall
lamp.
Retighten the screws.
