2003 MERCEDES-BENZ CL600 clock

21 At a glance
Cockpit
Item
Page
1
Combination switch

Turn signals
46


Windshield wipers
47


High beam
111
2
Cruise control lever

Cruise control
176


Distronic*
179
3
Instrument cluster
22,
111
4
Multifunction steering
wheel
24,
118
5
Gear range indicator, clock
22
Item
Page
6
Lever for voice control sys-
tem* (see separate operat-
ing instructions)
7
Parking assist* (Parktronic)
right front area warning in-
dicator
195
8
Overhead control panel
27
9
Glove box lock
199
10
Glove box lid release
199
11
Glove box
199
12
Center console
25,
26
13
Starter switch
31
14
Horn
Item
Page
15
Steering wheel adjustment
stalk
37
Heated steering wheel*
208
16
Parking brake pedal
44
17
Hood lock release
237
18
Parking brake release
44
19
Door control panel
28
20
Exterior lamp switch
46,
108
21
Headlamp washer button
154
22
Parking assist* (Parktronic)
left front area warning indi-
cator
195

23 At a glance
Instrument cluster
Item
Page
1
Coolant temperature
gauge
115
2
Fuel gauge with:Fuel reserve warning lamp
268
3
L
Left turn signal
indicator lamp
K
Right turn signal
indicator lamp
46
46
4
Speedometer with:v
Electronic Stability
Program (ESP)
warning lamp
264
l
Distance warning
lamp
1
1Vehicles without Distronic*: Warning lamp without
function. It illuminates with SmartKey in starter
switch position2. It should go out when the engine
is running.
265
5
Tachometer
115
Item
Page
6
Right display with:-
Antilock Brake Sys-
tem (ABS) malfunc-
tion indicator lamp
265
A
High beam head-
lamp indicator
111
<
Seat belt nonusage
warning lamp
266
7
J
Reset button
114
8
Display with:
Program mode
147
Gear range indicator
145
Digital clock (see
COMAND operating
instructions)
9
Multifunction display
with:
Trip odometer
117
Main odometer
117
Item
Page
Stored speed for:Cruise control or
176
Distronic*
179
10
Outside temperature indi-
cator
115
11
Left display with:1
Supplemental
restraint system
indicator lamp
266
;
Brake warning
lamp, except
Canada
267
3
Brake warning
lamp, Canada only
267
?
Engine malfunction
indicator lamp
268
12
Knob for instrument clus-
ter illumination
114

114 Controls in detailInstrument cluster
Instrument clusterA full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 22).
The instrument cluster is activated when
you


open a door


turn on the ignition


press the reset button
J
(page 22)


switch on the exterior lamps
You can change the instrument cluster set-
tings in the Instrument cluster submenu of
the control system (
Seite 134).
Instrument cluster illumination
1Knob for adjusting instrument cluster
illumination
Use knob1 to adjust the illumination
brightness for the instrument cluster.

Press the knob1.
The knob will pop out.
To brighten illumination

Turn the knob1 clockwise.
The instrument cluster illumination will
brighten.
To dim illumination

Turn the knob1 in the instrument clus-
ter counterclockwise.
The instrument cluster illumination will
dim.
iThe instrument cluster illumination is
dimmed or brightened automatically to
suit ambient light conditions.
The instrument cluster illumination will
also be adjusted automatically when
you switch on the vehicle’s exterior
lamps.

296 Practical hintsWhere will I find...?Vehicle jack
To prepare the vehicle jack for use
Remove the vehicle jack from the spare
wheel well under the trunk floor.

Push the crank handle up.

Turn the crank handle clockwise until it
engages (operational position).
Storing the vehicle jack in the trunk

Retract the vehicle jack arm to the
base of the vehicle jack.

Push the crank handle up.

Turn the crank handle counterclock-
wise to the end of the stop (storage po-
sition).Spare wheel
Removing the spare wheel

Take out vehicle tool kit tray 2.

Turn the luggage bowl 3 counterclock-
wise.

Remove the spare wheel 4.
Storing the spare wheel

Place spare wheel 4 in wheel well and
secure it with luggage bowl 3.

Turn the luggage bowl 3 clockwise to
its stop.

Place vehicle tool kit tray 2 in luggage
bowl 3.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.

298 Practical hintsUnlocking/locking in an emergencyUnlocking the trunk
If you are unable to unlock the trunk with
the SmartKey, open the trunk with the me-
chanical key as follows:Trunk lock
Insert the mechanical key into the
trunk lid lock.

Turn the key counterclockwise to
position1.

Press trunk lid lock2.
The trunk lid swings open.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey, lock it with the mechanical
key as follows:
Close the passenger door and the trunk
lid.

Press the central locking switch in the
center console (
page 95).

Check to see whether the locking knob
on the passenger door is still visible. If
necessary push it down manually.

Lock the driver’s door with the me-
chanical key.

Lock the trunk lid if necessary with the
mechanical key (
page 90).
!The trunk lid swings open automatical-
ly. Always make sure that there is suffi-
cient overhead clearance. A minimum
height clearance of 6.1 ft (1.90 m) is re-
quired to open the trunk lid. iUnlocking your vehicle with the me-
chanical key will trigger the anti-theft
alarm system. To cancel the alarm, do
one of the following:

Press button
Œ
or
‹
on the
SmartKey.


Insert the key in the starter switch.


If KEYLESS-GO* card present,
press the KEYLESS-GO* start/stop
button (
page 33).

301 Practical hints
Opening/closing in an emergency
Opening/closing in an emergency
Sliding/pop-up roof
The sliding/pop-up roof drive is located
behind the lens of the interior overhead
light.
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
1Lens
Pry off lens1 using a srewdriver.

Turn the key in the starter switch to
position1 or2.

Remove the crank from the Operator’s
Manual pouch.
2Crank

Insert crank2 through hole.

Turn crank2 clockwise to:

slide roof closed


raise roof at the rear

Turn crank2 counterclockwise to:

slide roof open


lower roof at the rear
The sliding/pop-up roof must be resyn-
chronized after being operated manually
(
page 175).

304 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Housing cover for high beam flasher
bulb, parking and standing lamp2Electrical connector for high beam
flasher housing bulb
3Parking and standing lamp
4Bulb socket for turn signal lamp
5Low beam and high beam (Bi-Xenon)
housing cover
High beam flasher bulb

Switch off the lights.

Open the hood (
page 237).

Press ends of housing cover1 tab to-
gether and remove cover.

Press connector2 downward.

Remove connector2 with the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

From below, press connector2 with
bulb upward onto the reflector.

Align housing cover1 and click into
place.
Front turn signal bulb

Switch off the lights.

Open the hood (
page 237).

Twist bulb socket4 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinsert bulb socket in lamp and twist
clockwise.
Warning!
G
Do not remove the cover for the Bi-Xenon
headlamp. Because of high voltage in xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
ommend that you have such work done by a
qualified technician at an authorized Mer-
cedes-Benz Center.

305 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.

Open the hood (
page 237).

Press ends of housing cover1 tab to-
gether and remove cover.

Pull out the bulb socket with the bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Align housing cover and click into
place.Side marker lamp bulb

Switch off the lights.

Carefully slide lamp towards rear.

Remove front end first.

Twist bulb socket counterclockwise
and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket, push in and twist
clockwise.

To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Replacing bulbs for rear lamps
Tail lamp assemblies
1Backup lamp (black socket)
2Turn signal lamp (white socket)
3Tail, standing and parking lamp (red
socket)
4Driver’s side: tail, parking and rear fog
lamp
Passenger’s side: tail and parking lamp
(red socket)