Page 94 of 376

94 Controls in detailSeatsHead restraints
Information on head restraint adjustment
can be found in the “Getting started” sec-
tion (
page 32).Front seat head restraints, manual seat
Removing front head restraints
Pull head restraint to its highest posi-
tion.
Push button1 and pull out head re-
straint.
Installing front head restraints
Insert head restraint and push it down
to the stop.
Push button1 and adjust head re-
straint to desired position.Front seat head restraints, power seat*
Removing front head restraints
Press switch1 upwards and hold until
the head restraint is fully extended.
Pull out head restraint.
Installing front head restraints
Press switch1 upwards and hold for
about five seconds.
Push the head restraint down until it
engages.
Adjust head restraint to desired posi-
tion (
page 34).
Warning!
G
For your protection, drive only with properly
positioned head restraints.
Adjust head restraint to support the back of
the head approximately at ear level.
Do not drive the vehicle without the seat
head restraints. Head restraints are intend-
ed to help reduce injuries during an acci-
dent.iTilt the backrest to the rear for easier
removal and installation of the head re-
straints.
Page 97 of 376

97 Controls in detail
Seats
Heated seats*
Both switches for the front seats are locat-
ed in the center console.
1Normal heating
2Rapid heating
Make sure that the ignition is switched
on.
All the lamps in the instrument cluster
light up.
Switching on seat heating
Press upper switch position1.A red indicator lamp on the switch
lights up.
Switching on rapid seat heating
Press lower switch position2.
Both red indicator lamps on the switch
light up.Switching off seat heating
If one indicator lamp is on, press upper
switch position1.
If both indicator lamps are on, press
lower switch position2.
!If one or both of the lamps on the seat
heater switch are blinking, there is in-
sufficient voltage available since too
many electrical consumers are turned
on. The seat heater switches off auto-
matically.
The seat heater will switch back on
again automatically as soon as suffi-
cient voltage is available.iThe system switches over to normal
heating mode after approximately five
minutes. Only one indicator lamp re-
mains lit.
iThe seat heater will be automatically
switched off after approximately
30 minutes.
Page 98 of 376

98 Controls in detailMemory function*
Memory function*
You can store up to three different settings
per key.
The following settings are saved for each
stored position:
Driver’s seat and backrest position
Steering wheel position
Driver’s side exterior rear view mirror
position
Passenger side exterior rear view mir-
ror position
Front passenger seat position
These key-dependent memory settings
can be deactivated if desired (
page 99).
!Prior to operating the vehicle, the driv-
er should check and adjust the seat
height, seat position fore and aft, and
seat backrest angle if necessary, to
ensure adequate control, reach and
comfort. The head restraint should also
be adjusted for proper height. Also see
airbag section (
page 57) for proper
seat positioning.
In addition, adjust the steering wheel to
ensure adequate control, reach, opera-
tion and comfort. Both the inside and
outside rear view mirrors should be ad-
justed for adequate rear vision.
Fasten seat belts. Infants and small
children should be seated in a properly
secured restraint system that complies
with U.S. Federal Motor Vehicle Safety
Standards 213 and 225 and Canadian
Motor Vehicle Safety Standards 213
and 210.2.
Warning!
G
Do not activate the memory function while
driving. Activating the memory function
while driving could cause the driver to lose
control of the vehicle.
Page 99 of 376

99 Controls in detail
Memory function*
The memory button and stored position
button are located on the door.
1Memory button
2Stored position button
Make sure that the ignition is switched
on or the relevant door is open and the
SmartKey is inserted in the starter
switch.
Storing positions into memory
Adjust the seats, steering wheel and
rear view mirrors to the desired posi-
tion (
page 32).
Turn button2 to selected memory po-
sition.
Press memory button1.
Release memory button and push
button2 within three seconds.
All the settings are stored at the select-
ed position.
Recalling positions from memory
Turn button2 to selected memory po-
sition.
Press and hold button2 until the seat,
steering wheel and rear view mirrors
have fully moved to the stored posi-
tions.iReleasing the button immediately
stops movement to the stored posi-
tions.Warning!
G
Do not operate the power seats using the
memory button if the seat backrest is in an
excessively reclined position. Doing so
could cause damage to front or rear seats.
First move backrest to an upright position.
Page 149 of 376
149 Controls in detail
Climate control
Climate control panel
The storage compartment between the
front seats can be ventilated (
page 155).
Information about “Rear passenger com-
partment adjustable air vents”
(
page 155).
Item
1
Air volume control for left center air
vent
2
Left center air vent, adjustable
3
Right center air vent, adjustable
4
Air volume control for right center
air vent
5
Air volume control for side air vent
6
Side air vent, adjustable
7
Side defroster vent, fixed
8
Climate control paneliFor draft-free ventilation, move the slid-
ers for the center air vents to the mid-
dle position.
Item
1
Air volume control
2
Left-side temperature control
3
Right-side temperature control
4
Air distribution control switch
5
Rear window defroster
6
AC cooling on/off (AC
OFF
)
7
Air distribution and air volume
(automatic)
8
Air recirculation
9
Defrosting
Page 198 of 376
198 Controls in detailLoading
Wrap strap4 around ski sack and arm-
rest.
Close clasp5 (arrows) and pull strap
tight to immobilize skis.
Connect snap hook6 of front strap to
eye7 located on center tunnel in front
of rear seat bench.Unloading and folding
Loosen strap, open clasp by pressing
tabs8 together (arrows).
Unload skis.
Close flap in trunk.
Disconnect snap hook6 from eye7.
Fold and flatten ski sack lengthwise
and place folded ski sack inside recess
of backrest.
Page 202 of 376

202 Controls in detailLoadingLoading instructions
The total load weight including vehicle oc-
cupants and luggage/cargo should not ex-
ceed the vehicle capacity weight indicated
on the certification tag which can be found
on the left door pillar.
The handling characteristics of a fully load-
ed vehicle depend greatly on the load dis-
tribution. It is therefore recommended to
load the vehicle according to the illustra-
tions shown, with the heaviest items being
placed towards the front of the vehicle.Always place items being carried against
front or rear seat backrests, and fasten
them as securely as possible.
The heaviest portion of the cargo should al-
ways be kept as low as possible since it in-
fluences the handling characteristics of
the vehicle.
Warning!
G
Always fasten items being carried as secure-
ly as possible.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle and can cause in-
jury to vehicle occupants unless the items
are securely fastened in the vehicle.
To help avoid personal injury during a colli-
sion or sudden maneuver, exercise care
when transporting cargo.
Never drive vehicle with trunk open. Deadly
carbon monoxide (CO) gases may enter ve-
hicle interior resulting in unconsciousness
and death.iThe trunk is the preferred place to carry
objects.
The enlarged cargo area should only be
used for items which do not fit in the
trunk alone.
Page 204 of 376
204 Controls in detailUseful featuresCup holder in front of seat armrestOpening cup holder
Slide cover1 rearward.
Push button2.
The cup holder opens automatically.Closing cup holder
Fold in direction of arrow until cup
holder engages.
Warning!
G
When not in use, keep the cup holder
closed. Place only containers that fit into the
cup holder to prevent spills. Use lids on
open containers and do not fill containers to
a height where the contents, especially hot
liquids, could spill during vehicle maneu-
vers.