2003 MERCEDES-BENZ C320 4MATIC WAGON automatic transmission

232 OperationAt the gas station
At the gas station
The fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking/unlocking the vehicle with
the remote control automatically
locks/unlocks the fuel filler flap.
Remove the key from the starter
switch.

Open the fuel filler flap by pushing at
the point indicated by the arrow.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in the recess
on the fuel filler flap.

Only fill your tank until the filler nozzle
unit cuts out – do not top up or overfill.

Replace the fuel cap by turning it to the
right.
You will hear when the fuel cap is tight-
ened.

Close the fuel filler flap.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious inju-
ry. Whenever you are around gasoline, avoid
inhaling fumes and skin contact, extinguish
all smoking materials. Never allow sparks,
flame or smoking materials near gasoline!Warning!
G
Flexible Fuel Vehicles (MY 2003
Mercedes-Benz C 320 models, except those
equipped with manual transmission or
4MATIC*) only:
Ethanol fuel (E85) and its vapors are highly
flammable, poisonous and burn easily. Etha-
nol fuel can cause serious injuries if ignited
or if you come into contact with it or inhale
fumes of it. Avoid inhalation of Ethanol
fumes and skin contact with Ethanol. Extin-
guish all open flames before refueling. Never
smoke or create sparks close to Ethanol.
Warning!
G
Overfilling of the fuel tank may create pres-
sure in the system which could cause a gas
discharge. This could cause the gas to spray
back out when removing the fuel pump noz-
zle, which could cause personal injury.
S203 MY03_A.book Page 232 Tuesday, January 28, 2003 2:22 PM

237 Operation
Engine compartment

Screw the cap back on the filler neck.
Other display messages
If there is excessive engine oil with the en-
gine at normal operating temperature, the
following message will appear:
ENGINE OIL LEVEL – REDUCE OIL LEVEL 
Have excess oil siphoned.
If the key is not turned to position2 in the
starter switch, the following message will
appear:
FOR ENGINE OIL LEVEL IGNITION ON
PLEASE!
Switch on the ignition.If you see the message:
OBSERVE WAITING PERIOD
Wait five minutes before repeating
check procedure.
If you see the message:
ENGINE OIL LEVEL – NOT WHEN ENGINE ON! 
Turn off the engine. If engine is at nor-
mal operating temperature, wait five
minutes before checking oil. If the en-
gine is not yet at normal operating tem-
perature, you must wait 30 minutes
before checking oil.
If a proper oil level check cannot be per-
formed, the following message will appear:
MEASURING NOT POSSIBLE
.

Repeat the engine oil level check after
a short while.
More information on engine oil can be
found in the “Technical data” section
(
page 330).
Transmission fluid level
The transmission fluid level does not need
to be checked. If you notice transmission
fluid loss or gear shifting malfunctions,
have an authorized Mercedes-Benz Center
check the automatic transmission.
S203 MY03_A.book Page 237 Tuesday, January 28, 2003 2:22 PM

309 Practical hints
Jump starting
The battery is located in the engine com-
partment on the right hand side. The termi-
nals for jump starting are located in front
of the battery.
Make sure that the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift selector lever to positionP (man-
ual transmission to Neutral).1Positive terminal of charged battery
2Positive under hood terminal in front of
discharged battery
3Negative terminal of charged battery
4Negative under hood terminal in front
of discharged battery

Connect positive terminal1 of the
charged battery with the under hood
terminal2 in front of the discharged
battery with the jumper cables. Clamp
cable to charged battery1 first.

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminal3 of the
charged battery with the under hood
terminal4 in front of the discharged
battery with the jumper cables. Clamp
cable to charged battery3 first.

Start the engine of the disabled vehi-
cle.
Now you can again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
negative terminals3 and4 and then
from positive terminals1 and2.

Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 239).
!Vehicles with automatic transmission
or 4MATIC*:
Do not tow-start the vehicle.
S203 MY03_A.book Page 309 Tuesday, January 28, 2003 2:22 PM

310 Practical hintsTowing the vehicle
Towing the vehicleMercedes-Benz recommends that the
vehicle be transported with all wheels off
the ground using flatbed or appropriate
wheel lift/dolly equipment. This method is
preferable to other types of towing.When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front wheels raised (except
vehicles with 4MATIC*) only so far as
necessary to have the vehicle moved to a
safe location where the recommended
towing methods can be employed.
!Use flatbed or wheel lift/dolly equip-
ment with key in starter switch turned
to position0.
Do not tow with sling-type equipment.
Towing with sling-type equipment over
bumpy roads will damage radiator and
supports.
To prevent damage during transport,
do not tie down vehicle by its chassis or
suspension parts.
Switch off the tow-away alarm
(page 80) and deactivate the auto-
matic central locking (
page 88).
!Vehicles with automatic transmission
and/or 4MATIC*:
Do not tow-start the vehicle.!Vehicles with 4MATIC*:
Do not tow with one axle raised. Doing
so could damage the transfer case,
which is not covered by the
Mercedes-Benz Limited Warranty.
All wheels must be on or off the ground.
Observe instructions for towing the
vehicle with all wheels on the ground.
!If the vehicle is towed with the front
axle raised (not permissible for vehicles
with 4MATIC*), the engine must be
shut off (key in starter switch
position0 or1). Otherwise the ESP will
immediately be engaged and will apply
the rear wheel brakes.
When towing the vehicle with all wheels
on the ground, the selector lever must
be in positionN (manual transmission:
gears disengaged) and the key must be
in starter switch position2.
When towing the vehicle with all wheels
on the ground or the front axle raised,
the vehicle may be towed only for
distances up to 30 miles (50 km) and
at a speed not to exceed 30 mph
(50 km/h).
S203 MY03_A.book Page 310 Tuesday, January 28, 2003 2:22 PM

328 Technical dataFuels, coolants, lubricants etc.
Fuels, coolants, lubricants etc.Capacities
Vehicle components and their respective lubricants must match. Therefore use only
brands tested and recommended by us.
Please refer to the Factory Approved Service Products pamphlet, or inquire at
your Mercedes-Benz Center.
Model
Capacity
Fuels, coolants, lubricants etc.
Engine with oil filter
C 240
C 320
C 240 4MATIC
C 320 4MATIC
7.9 US qt (7.5 l)
7.9 US qt (7.5 l)
7.4 US qt (7.0 l)
7.4 US qt (7.0 l)
Recommended engine oils
Automatic transmission
8.5 US qt (8.0 l)
MB Automatic Transmission Oil
1
1MB part no. 001 989 21 03 10Manual transmission
1.3 US qt (1.2 l)
MB Manual Transmission Oil
2
2MB part no. 001 989 26 03 10Rear axle
1.2 US qt (1.1 l)
Hypoid gear oil SAE 85 W 90
Front axle
C 240 4MATIC
C 320 4MATIC
0.5 US qt (0.46 l)
Hypoid gear oil SAE 85 W 90
Transfer case
C 240 4MATIC
C 320 4MATIC
approx. 0.62 US qt (0.59 l)
MB Automatic Transmission Oil
1
Power steering
approx. 1.1 US qt (1.0 l)
MB Power Steering Fluid (Pentosin CHF 11S)
Front wheel hubs
approx. 2.1 oz (60 g) each
High temperature roller bearing grease
Brake system
0.5 US qt (0.5 l)
MB Brake Fluid (DOT 4+)
Cooling system
approx. 6.8 US qt (6.4 l)
MB 325.0 Anticorrosion/Antifreeze Agent
S203 MY03_A.book Page 328 Tuesday, January 28, 2003 2:22 PM

340 Technical termsCOMAND*
(Cockpit Management and Data Sys-
tem)
Information and operating center for
vehicle sound and communications
systems, including the radio and navi-
gation system, as well as for other op-
tional equipment (CD changer*,
telephone*, etc.).
Control system
The control system is used to call up vehi-
cle information and to change component
settings. Information and messages ap-
pear in the multifunction display. The driv-
er uses the buttons on the multifunction
steering wheel to navigate through the sys-
tem and to adjust settings.
Cruise control
Driving convenience system for automati-
cally maintaining the vehicle speed set by
the driver.Engine number
The number set by the manufacturer and
placed on the cylinder block to uniquely
identify each engine produced.
Engine oil viscosity
Measurement for the inner friction (viscos-
ity) of the oil at different temperatures. The
higher the temperature an oil can tolerate
without becoming thin, or the lower the
temperature it can tolerate without be-
coming viscous, the better the viscosity.
ESP
(Electronic Stability Program)
Improves vehicle handling and direc-
tional stability.
ETD
(Emergency Tensioning Device)
Device which deploys in certain frontal
and rear collisions exceeding the sys-
tem's threshold to tighten the seat
belts.
->SRSFSS
(Flexible Service System)
Service indicator in the multifunction
display that informs the driver when
the next vehicle maintenance service is
due.
Gear range
Number of gears which are available to the
automatic transmission for shifting. The
automatic gear shifting process can be
adapted to specific operating conditions
using the selector lever.
GPS
(Global Positioning System)
Satellite-based system for relaying
geographic location information to and
from vehicles equipped with special re-
ceivers. Employs CD digital maps for
navigation.S203 MY03_A.book Page 340 Tuesday, January 28, 2003 2:22 PM

342 Technical termsPower train
Collective term designating all compo-
nents used to generate and transmit
motive power to the drive axles, includ-
ing


engine


clutch/torque converter


transmission


transfer case


drive shaft


differential


axle shafts/axles
Program mode selector switch
Used to switch the automatic transmission
between standard operation S and winter
operation W.Remote Vehicle Diagnostics
Transmission of vehicle data and current
location to the Mercedes-Benz Customer
Assistance Center for subscribers to
Tele Aid service.
REST
(Residual engine heat utilization)
Feature that uses the engine heat
stored in the coolant to heat the vehi-
cle interior for a short time after the en-
gine has been turned off.
Restraint systems
Seat belts, belt tensioners, airbags and
child restraint systems. As independent
systems, their protective functions com-
plement one another.RON
(Research Octane Number)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line's ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as AN-
TI-KNOCK INDEX.
Shift lock
When the vehicle is parked, this lock pre-
vents the transmission selector lever from
being moved out of position P without key
turned and brake pedal depressed.
SRS
(Supplemental Restraint System)
Seat belts, emergency tensioning de-
vice and airbags. Though independent
systems, they are closely interfaced to
provide effective occupant protection.
S203 MY03_A.book Page 342 Tuesday, January 28, 2003 2:22 PM

345 Index
A
ABS 23, 73, 339
ABS control 74
Malfunction indicator lamp 255
Messages in display 261
Warning lamp 255
Accelerator position, automatic
transmission 140
Accident
In case of 50
Activating
Air circulation mode 148
Air conditioning (cooling) 150, 159
Air recirculation mode 148, 156
Anti-theft alarm system 79
Automatic climate control 153
Central locking (control system) 125
Climate control 145
Defrost 147, 156
Easy-entry/exit feature 126
ESP 77
Exterior headlamps 47
Exterior lamps 99
Exterior rear view mirror parking
position 142
Hazard warning flasher 101Headlamps 47
High beams 101
Ignition 31
Immobilizer 52, 79
Rear fog lamp 99
Rear window defroster 149, 158
Residual heat 159
Seat heater 94
Tow-away alarm 80
Windshield wipers 48
Adding
Coolant 238
Engine oil 236
Additional turn signals 292
Adjustable air vents, rear passenger
compartment 151, 160
Adjusting 32
Air distribution 147, 155
Air volume 147, 155
Backrest tilt 33, 35
Exterior rear view mirror 39
Head restraint height 33, 35, 36
Head restraint tilt 34, 35, 36
Head restraints 36
Inside rear view mirror 38
Instrument cluster illumination 104Manual seat 33
Mirrors 38
Multicontour seat* 93
Power seat 34
Rear seat head restraints 35
Seat cushion depth 93
Seat cushion tilt 33, 35
Seat fore and aft adjustment 33, 34
Seat height 33, 35
Seats 32
Steering column height 38
Steering column length 38
Steering wheel 37
Air conditioning (cooling)
Turning off 150, 159
Turning on 150, 159
Air conditioning refrigerant 330
Air distribution
Adjusting 147, 155
Air pressure see Tire inflation
pressure 242
Air recirculation mode 148, 156
Activating 148, 156
Deactivating 148, 157
Air vents, rear passenger compartment
Adjustable 151, 160
S203 MY03_A.book Page 345 Tuesday, January 28, 2003 2:22 PM