Page 218 of 376
218 Controls in detailUseful features
Programming or reprogramming the in-
tegrated remote control
Turn key in the starter switch to
position1 or2.
Hold the end of the hand-held transmit-
ter of the device you wish to train ap-
proximately 2in to 5in (5cm to 12cm)
away from the surface of the integrated
remote control located on the inside
rear view mirror, keeping the indicator
lamp in view.
Using both hands, simultaneously push
the hand-held transmitter button and
the desired integrated remote control
button. Do not release the buttons until
completing next step.
The indicator lamp on the integrated
remote control will flash, first slowly
and then rapidly. The rapid flashing
lamp indicates successful program-
ming of the new frequency signal.
When the indicator lamp flashes rapid-
ly, release both buttons.
Warning!
G
When programming a garage door opener,
the door moves up or down.
When programming or operating the remote
control make sure there is no possibility of
anyone being injured by the moving door.iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact your authorized
Mercedes-Benz Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iFor operation in the USA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.
Page 219 of 376
219 Controls in detail
Useful features
To program the remaining two buttons,
repeat the above steps.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion of
this text. (A second person may make the
following training procedures quicker and
easier.)
Locate training button on the garage
door opener motor head unit. Exact location and color of the button
may vary by garage door opener brand.
If there is difficulty locating the trans-
mitting button, refer to garage door
opener operator’s manual.
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds time to initiate the
following step.
Firmly press and release the pro-
grammed integrated remote control
transmit button.
Press and release same button a sec-
ond time to complete the training pro-
cess.
Some garage door openers may require
you to do this procedure a third time to
complete the training.
Confirm the garage door operation by
pressing the programmed button on
the integrated remote control transmit-
ter. Canadian programming
During programming, your hand-held
transmitter may automatically stop trans-
mitting.
Continue to press and hold the inte-
grated remote control transmitter but-
ton (refer to steps two through four in
the “Programming” portion) while you
press and re-press (“cycle”) your
hand-held transmitter every two sec-
onds until the frequency signal has
been learned.
Upon successful training, the indicator
lamp will flash slowly and then rapidly
after several seconds.
iIf, after several attempts, you do not
successfully program the integrated re-
mote control device to learn the signal
of the hand-held transmitter, the ga-
rage door opener could be equipped
with the “rolling code feature”.
Page 355 of 376
355 Index
Fuel requirements 333
For ethanol fuel 334
Fuel reserve tank
Message in display 272
Fuel tank
Capacity 330
Filler flap 233
Fuels, coolants, lubricants etc.
Capacities 329
Functions (control system) 112, 115
Resetting 120
Fuse box 312
Fuse chart 312
Fuse extractor 313
Fuses 312
Auxiliary fuse box in the trunk 313
F us e box in e ng ine com pa rtm ent 3 12
Fuse box in passenger
compartment 312
Fuse chart 312
Fuse extractor 313
Spare fuses 313G
Garage door opener 27, 217
Erasing in remote control 220
Integrated remote control 218
Rolling code programming 219
Gasoline see Fuel 234
Gasoline additives 334
Gear range 342
Automatic transmission 140
Limiting 140
Shifting into optimal 139
Gear range limit
Canceling 139
Gear selector lever
Cleaning 252
Position 141
Global
Locking 85
Unlocking 85
Global Positioning System (GPS) 342
Glove box 21, 203
Closing 203
Opening 203
Good visibility 144
GPS 342
GPS see COMAND* 210H
Halogen-type
Front lamp bulbs 292
Hand-held transmitter
Programming integrated remote
control 218
Hands-free microphone 27
Hard plastic trim items
Cleaning 252
Hazard warning flasher 104
Switching off 104
Switching on 104
Head restraints 94
Manual seats 33
Power seats* 35
Rear seats 35
Headlamp cleaning system* 241
Headlamp shut-off delay
see Delayed shut-off, exterior lamps
Headlamps
Automatic control 102
Bi-Xenon type*
Replacing bulbs 293
Bi-Xenon* 341
Cleaning 251
Cleaning system* 146, 241, 338
Page 356 of 376
356 Index
Halogen-type
Replacing bulbs 292
Refilling washer fluid 241
Switching off 52
Switching on 47
Washer fluid 338
Headliner
Cleaning 252
Heated seats* 97
Height adjustment
Head restraints 33, 35, 37
Seat belts 43
Steering wheel 37
High beam flasher 47, 104
High beam headlamps
Messages in display 274
Replacing bulbs 290, 292
Switching on 104
High beam headlamps xenon type*
Replacing bulbs 293
High mounted brake lamp 291
Hood 235
Closing 236
Message in display 272
Opening 235
Hydroplaning 227I
Identification labels 318
Certification label 318
Vehicle identification
number (VIN) 318
Ignition 31
Switching on 44
Immobilizer 79
Activating 79
Deactivating 79
Indicator lamps
see Lamps, indicator and warning
Infant and child restraint systems 65
Installing 68
LATCH child seat anchors 69
Information
About service and warranty 10
Button for Tele Aid* 214
Inside rear view mirror
Adjusting 39
Antiglare 144
Installing
Infant and child restraint systems 68
Towing eye bolt 311
Wiper blades 296Instrument cluster 22, 107, 342
Cleaning 252
Coolant temperature display 108
Illumination 107
Lamps in 256–259
Multifunction display 111
Outside temperature indicator 110
Selecting language 124
Instrument lighting 107, 108
Instruments and controls see Cockpit 20
Integrated remote control
Canadian programming 219
Erasing memory 220
Hand-held transmitter 218
Operating 220
Rolling code programming 219
Interior lighting 105
Activating automatic control 105
Deactivating automatic control 105
Delayed shut-off 127
Manual operation 105
Interior storage spaces 203
Armrest 206
Cup holder 204, 205
Glove box 203