2003 MERCEDES-BENZ C230 KOMPRESSOR Light bulbs

234 OperationAt the gas station
Check regularly and before a long trip
1Coolant level
More information on the coolant level
can be found in the “Operation” section
(
page 238).
2Brake fluid (fuse box cover removed)
More information on brake fluid can be
found in the “Technical data” section
(page 332).
Removing fuse box cover
(page 312).
3Windshield washer and headlamp
cleaning system*
For more information on refilling the
reservoir, see the “Operation” section
(page 241).Engine oil level
More information on engine oil can be
found in the “Operation” section
(
page 236).
Opening hood (
page 235).
Coolant
For normal replenishing, use water (pota-
ble water quality). More information on
coolant can be found in the “Operation”
section (
page 238).
Vehicle lighting
Check function and cleanliness. For more
information on replacing light bulbs, see
the “Practical hints” section (
page 290).
Exterior lamp switch (
page 101).
Tire inflation pressure
More information on tire inflation pressure
can be found in the “Operation” section
(
page 243).
iUse only premium unleaded gasoline
with a minimum Posted Octane Rating
of 91 (average of 96 RON / 86 MON).
Information on gasoline quality can
normally be found on the fuel pump.
More information on gasoline can be
found in the Factory Approved Service
Products pamphlet.
Flexible Fuel Vehicles (MY 2003
Mercedes-Benz C 320 models, except
those equipped with manual transmis-
sion or 4MATIC*):
More information on Flexible Fuel Vehi-
cles can be found in the “Technical da-
ta” section (
page 334).
iLeaving the engine running and the fuel
cap open can cause the
?
lamp to
illuminate.
See also “Practical hints” section
(
page 259).

290 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
Bulbs Front lamps
iBackup bulbs will be brought into use
when the following lamps malfunction:

Standing lamps


Tail lamps


Rear fog lamp
Lamp
Type
1
Additional turn
signal lamps
LED
2
Turn signal lamp
Halogen
Turn signal lamp
Bi-Xenon*
1156 A
2357 A
3
Low beam Halogen
Low and high beam
H7 (55 W)
Bi-Xenon*
4
High beam
H7 (55 W)
Parking and
standing lamps
W5W
5
Fog lamp
HB4/9006
(55 W)
6
Side marker lamp
W5W

291 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement


Use only 12 volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.


Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center:

Additional turn signal lamps in the
exterior rear view mirrors


High mounted brake lamp


Xenon lamps


Front fog lamps
Lamp
Type
7
High mounted brake
lamp
LED
8
Brake lamp
P21W
9
Turn signal lamp
PY 21 W
10
Backup lamp
P21W
11
Tail, parking,
standing and side
marker lamp
R5W
12
License plate lamps
C5W
13
Rear fog lamp,
driver’s side
P21W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas.
A bulb can explode if you

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

292 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Halogen headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam head-
lamp, parking and standing lamp
3Headlamp cover for low beam head-
lamp4Low beam headlamp bulb
5High beam headlamp bulb
6Bulb socket for parking and standing
lamp bulb
Low and high beam bulb

Switch off the lights.

Open the hood (
page 235).

Press the clamp and remove headlamp
cover2 or 3.

Pull electrical connector off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base
locates in the recess on the holder.

Clip the retainer springs and plug the
connector onto the bulb.

Align headlamp cover2 or 3 and click
into place.
Front turn signal lamp bulb

Switch off the lights.

Open the hood (
page 235).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinsert bulb socket in lamp and twist
clockwise.

293 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.

Open the hood (
page 235).

Press the clamp and remove headlamp
cover2.

Pull out the bulb socket6 with the
bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Align headlamp cover2 and click into
place.Bi-Xenon* headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam head-
lamp, parking and standing lamp
3Headlamp cover for Bi-Xenon lamp4High beam headlamp bulb
5Bayonet socket for high beam
headlamp bulb
6Bulb socket for parking and standing
lamp bulb
High beam bulb

Switch off the lights.

Open the hood (
page 235).

Press the clamp and remove headlamp
cover2.

Pull electrical connector4 off.
Warning!
G
Do not remove the cover3 for the Bi-Xenon
headlamp. Because of high voltage in
Bi-Xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.


294 Practical hintsReplacing bulbs
Twist bayonet socket5 counterclock-
wise to the stop (do not remove).

Pull the bulb out of the socket.

Insert the new bulb so that the base
locates in the recess in the bayonet
socket5.

Twist bayonet socket clockwise until
you hear it snap into place.

Plug the connector onto the bulb.

Align headlamp cover2 and click into
place.
Front turn signal lamp bulb

Switch off the lights.

Open the hood (
page 235).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinsert bulb socket in lamp and twist
clockwise.
Parking and standing lamp bulb

Switch off the lights.

Open the hood (
page 235).

Press the clamp and remove headlamp
cover2.

Pull out the bulb socket6 with the
bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Align headlamp cover2 and click into
place.
Side marker lamp bulb
Switch off the lights.

Carefully slide lamp towards rear.

Remove front end first.

Twist bulb socket counterclockwise
and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket, push in and twist
clockwise.

To reinstall lamp, set rear end in
bumper and let front end snap into
place.

295 Practical hints
Replacing bulbs
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off lights.

Open trunk lid.
1Locking lever

Fold trim to the side.

Turn locking lever1 to vertical position
and remove bulb carrier.2Rear fog lamp, driver’s side
3Back up lamp
4Stop lamp
5Turn signal lamp
6Tail, parking, standing and side marker
lamp

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb and turn clockwise.

Reinstall bulb socket.

Reinstall bulb holder and close trim
panel.License plate lamp
1Screw

Switch off the lights.

Loosen both screws1 and remove
lamp.

Replace the tubular lamp and reinstall
lamp.

Retighten the screws.

356 Index
Halogen-type
Replacing bulbs 292
Refilling washer fluid 241
Switching off 52
Switching on 47
Washer fluid 338
Headliner
Cleaning 252
Heated seats* 97
Height adjustment
Head restraints 33, 35, 37
Seat belts 43
Steering wheel 37
High beam flasher 47, 104
High beam headlamps
Messages in display 274
Replacing bulbs 290, 292
Switching on 104
High beam headlamps xenon type*
Replacing bulbs 293
High mounted brake lamp 291
Hood 235
Closing 236
Message in display 272
Opening 235
Hydroplaning 227I
Identification labels 318
Certification label 318
Vehicle identification
number (VIN) 318
Ignition 31
Switching on 44
Immobilizer 79
Activating 79
Deactivating 79
Indicator lamps
see Lamps, indicator and warning
Infant and child restraint systems 65
Installing 68
LATCH child seat anchors 69
Information
About service and warranty 10
Button for Tele Aid* 214
Inside rear view mirror
Adjusting 39
Antiglare 144
Installing
Infant and child restraint systems 68
Towing eye bolt 311
Wiper blades 296Instrument cluster 22, 107, 342
Cleaning 252
Coolant temperature display 108
Illumination 107
Lamps in 256–259
Multifunction display 111
Outside temperature indicator 110
Selecting language 124
Instrument lighting 107, 108
Instruments and controls see Cockpit 20
Integrated remote control
Canadian programming 219
Erasing memory 220
Hand-held transmitter 218
Operating 220
Rolling code programming 219
Interior lighting 105
Activating automatic control 105
Deactivating automatic control 105
Delayed shut-off 127
Manual operation 105
Interior storage spaces 203
Armrest 206
Cup holder 204, 205
Glove box 203