2003 MERCEDES-BENZ C-Class navigation

159 Navigation
Route guidance
You can either select the map north or po-
sition it with the driving direction pointing
up.North-up: Map is displayed facing north 1Selecting map orientation
North arrow ! or compass needle <
(black tipping pointing to the north)
2Symbol for current vehicle locationSelecting driving direction pointing up
Heading-up: Map is displayed facing driving
direction pointing up
Turn the right-hand rotary/push-button
v to highlight 1 and press to confirm.
Symbol 2 points in the driving direc-
tion, the compass needle will appear.To return to North-up

Turn the right-hand rotary/push-button
v to highlight 1 and press to confirm.
The north arrow will appear again.
Selecting map orientation
Map orienta-
tion
Characteristics
North-up
North arrow always
points to the top
The symbol for the cur-
rent vehicle location is
turning on the map
Heading-up
The symbol for the cur-
rent vehicle location al-
ways points to the top
The compass needle is
turning, the black point
always points north

160 NavigationRoute guidanceYou can store a way point during route
guidance.
1Activate “Way Point” menu
Turn the right-hand rotary/push-button
v to highlight 1 and press to confirm.
The “Way Point” menu will appear.
“Way Point” menu2Select a category
3Activate the main address menu
(
page 123)
4Activate the “Points of Interest” selec-
tion menu (
page 137)
5Activate the main destination memory
menu (
page 174)
6Activate the “Coordinate Destination”
input menu (
page 135)

Turn the right-hand rotary/push-button
v to highlight 2 to 6 press to confirm.

Select the desired way point.

Start route guidance.
Marking a way point

161 Navigation
Route guidance
Starting route guidance
Press the right-hand rotary/push-
button v to confirm “Start
Guidance…”.You will now see the information corres-
ponding to route calculation and hear the
voice output: “The route to your intermedi-
ate destination is being calculated”.
The previously selected route mode will be
maintained.
After you reach the way point, you will con-
tinue to follow the route to the original in-
put destination.
iAfter you have entered an address, the
menu fields “Intersection…” and
“House No...” may appear in black, indi-
cating that it is possible to select them.
P82.85-9220-31

162 NavigationRoute guidanceCancel the calculation 
Press the right-hand rotary/push-
button v to confirm “Cancel”.Deleting way point

Turn the right-hand rotary/push-button
v to highlight “Stop” in the symbol or
map display and press to confirm.
The “Way Point” menu will appear, “De-
lete stop-over...” is highlighted.
If the menu bar is not visible in the
map:
Turn the right-hand rotary/push-
button v.
The menu bar will appear.

Press the right-hand rotary/push-
button v to confirm “Delete stop-
over...”.
The way point has been deleted.
If you do not want to delete the way point

Press *.iIt is also possible to delete a way point
in the menu (
page 167).

163 Navigation
Route guidance
Main detour menu
1It is possible to block route sections
ahead
2Ends the detour function, the previous
route is calculated

Traffic Jam Ahead/Detour in Route
List not activated:
“Cancel” cannot be selected


Traffic Jam Ahead/Detour in Route
List activated:
“Cancel” is highlighted
3It is possible to block route sections in
the route list (
page 165)

Press ) at any time.
The main detour menu will appear.

Turn the right-hand rotary/push-button
v to highlight the desired menu field
and press to confirm.
^
Selecting a detour
P82.85-9222-31
1223
iTraffic jams are identified by the driver,
not by the COMAND.
If you switch off COMAND for more than
30 minutes during active route
guidance, all manually entered traffic
jams are deleted.

164 NavigationRoute guidanceTraffic jam ahead
If a traffic jam lies ahead, you can block the
route sections following the next intersec-
tion/the next turn-off.Traffic jam menu1Length of the blocked route section in
miles

Turn the right-hand rotary/push-button
v to highlight “Traffic Jam Ahead...” in
the main detour menu and press to
confirm.
The traffic jam menu will appear.Entering the length of the blocked route
section
Increasing the blocked section

Turn the right-hand rotary/push-button
v to the right.
Decreasing the blocked section

Turn the right-hand rotary/push-button
v to the left.
Calculating detour

Press the right-hand rotary/push-
button v.
The route will be re-calculated. An in-
formation menu will appear.
Then COMAND continues route
guidance.
iCOMAND suggests reasonable route
sections.
Minimum/maximum length of detour is
governed by the logical grouping of rou-
te sections. If additional detour seg-
ments are required after the original
detour, they must be requested indivi-
dually.
iYou can also select “Traffic Jam Ahead”
during the course of a detour. The cur-
rent detour will then be cancelled.

165 Navigation
Route guidance
Detour in route list
Turn the right-hand rotary/push-button
v to highlight “Detour in Route List” in
the main detour menu and press to
confirm.
The message “The route list is being
calculated” will appear.
Then the route list will appear.
Route list1Street cannot be blocked off
2Symbol “+”: street contains several
sections which can be blocked off
3Blocked street will appear in redDisplaying an entry in full in a window

Press u.

Press u again to remove the window.

166 NavigationRoute guidanceCalling detailed route list Detailed route list4Symbol “-” - sections of a road are dis-
played
Press +.
The detailed route list will appear.Blocking off several streets/street sec-
tions

Turn the right-hand rotary/push-button
v to the right.
With each turn, you will block another
section.
The road name will appear in red.
Undoing street block

Turn the right-hand rotary/push-button
v to the left.
The street name will appear in black
again.
Switching back to the route list

Press ,.
The symbol “+” appears in front of the
street section.
The blocking function is still active.Canceling blocking function, do not recal-
culate the route

Press *.
The traffic jam menu will appear.
Ending the blocking function, re-calcula-
ting the route with the blocks selected

Press the right-hand rotary/push-
button v.
COMAND re-calculates the route in the
previously selected calculation mode.
A corresponding message will appear.
Then the symbol display will appear
again and COMAND will continue route
guidance.