2003 MAZDA MODEL MX-5 MIATA change time

A Word to Mazda Owners
Form No. 8R09-EA-02G
Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete
customer satisfaction in mind.
To help ensure enjoyable and trouble-free operation of your Mazda, read this manual
carefully and follow its recommendations.
An Authorized Mazda Dealer knows your vehicle best. So when maintenance or service is
necessary, that’s the place to go.
Our nationwide network of Mazda professionals is dedicated to providing you with the best
possible service.
We assure you that all of us at Mazda have an ongoing interest in your motoring pleasure
and in your full satisfaction with your Mazda product.
Mazda Motor CorporationHIROSHIMA, JAPAN
©2002 Mazda Motor Corporation
Printed in Japan Mar. 2003(Print4)
Important Notes About This Manua
l
Keep this manual in the glove box as a handy reference for the safe and enjoyable use of
your Mazda. Should you resell the vehicle, leave this manual with it for the next owner.
All specifications and descriptions are accurate at the time of printing. Because
improvement is a constant goal at Mazda, we reserve the right to make changes in
specifications at any time without notice and without obligation.
Air Conditioning and the Environment
Your Mazda’s genuine air conditioner is filled with HFC134a (R134a), a refrigerant that
has been found not to damage the earth’s ozone layer. If the air conditioner does not
operate properly, consult an Authorized Mazda Dealer.
Please be aware that this manual applies to all models, equipment and options. As a
result, you may find some explanations for equipment not installed on your vehicle.
J07R_8R09_EA_02G_Edition4.book Page 1 Monday, February 3, 2003 1:16 PM

2-3
Essential Safety Equipment
Seats
Form No. 8R09-EA-02G

Seat ReclineTo change the seatback angle, lean
forward slightly while raising the lever.
Then lean back to the desired position and
release the lever.
Make sure the lever returns to its original
position and the seatback is locked in
place by attempting to push it forward and
backward.
Reclining:
Sitting in a reclined position while the
vehicle is moving is dangerous
because you don
’t get the full
protection from seat belts. During
sudden braking or a collision, you
can slide under the lap belt and suffer
serious internal injuries. For
maximum protection, sit well back
and upright.
Unlocked Seatback:
A seatback plays an important role in
your protection in a vehicle. Leaving
the seatback unlocked is dangerous as
it can allow passengers to be ejected
or thrown around and baggage to
strike occupants in a sudden stop or
collision, resulting in severe injury.
After adjusting the seatback at any
time, even when there are no other
passengers, rock the seatback to make
sure it is locked in place.
WARNING
When returning a rear-reclined
seatback to its upright position, make
sure you support the seatback while
operating the seatback lever. If the
seatback is not supported, it will flip
forward suddenly and could cause
injury.
Lever
CAUTION
J07R_8R09_EA_02G_Edition4.book Page 3 Monday, February 3, 2003 1:16 PM

5-1
Form No. 8R09-EA-02G
5Driving Your Mazda
Explanation of instruments and controls.
Starting and Driving ................................................................... 5- 2
Ignition Switch ........................................................................ 5- 2
Starting the Engine .................................................................. 5- 3
Brake System ........................................................................... 5- 4
Manual Transmission Operation ............................................. 5- 8
Automatic Transmission Controls ........................................... 5-10
Power Steering ......................................................................... 5-13
Cruise Control ......................................................................... 5-14
Instrument Cluster and Indicators ............................................ 5-17
Meters and Gauges .................................................................. 5-17
Warning/Indicator Lights and Beeps ........................................ 5-22
Warning/Indicator Lights ......................................................... 5-22
Beeps ....................................................................................... 5-29
Switches and Controls ................................................................. 5-30
Lighting Control ...................................................................... 5-30
Turn and Lane-Change Signals ............................................... 5-31
Fog Lights ................................................................................ 5-31
Daytime Running Lights (Canada) .......................................... 5-32
Windshield Wipers and Washer ............................................... 5-32
Rear Window Defroster ........................................................... 5-34
Horn ......................................................................................... 5-34
Hazard Warning Flasher .......................................................... 5-35
J07R_8R09_EA_02G_Edition4.book Page 1 Monday, February 3, 2003 1:16 PM

5-15
Driving Your Mazda
Starting and Driving
Form No. 8R09-EA-02G

To Set Speed
1. Activate the cruise control system.
2. Accelerate to the desired speed, which
must be more than 40 km/h (25 mph).
3. Turn the control knob to SET/COAST and release it at the speed you want.
Release the accelerator at the same
time.
Don ’t continue to hold the knob. Until
you release it, speed will continue to
drop (unless you continue to
accelerate) and you ’ll miss the desired
speed.

To Increase Cruising Speed
Follow either of these procedures.
• Turn the control knob to RESUME/
ACCEL and hold it. Your vehicle will
accelerate.
Release the knob at the speed you
want.
• Accelerate to the desired speed.
Turn the control knob to SET/COAST
and release it immediately.
NOTE
•The SET function can
’t be activated
until about 2 seconds after the
CRUISE MAIN switch has been
engaged.
• On a steep grade, the vehicle may
momentarily slow down going up or
speed up while going down.
Control knob
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere
with it or change the set speed.
Take your foot off the accelerator to
return to the set speed.
Control knob
Control knob
J07R_8R09_EA_02G_Edition4.book Page 15 Monday, February 3, 2003 1:16 PM

6-11
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G
Signals from an FM transmitter are
similar to beams of light because they do
not bend around corners, but they do
reflect. Unlike AM signals, FM signals
cannot travel beyond the horizon.
Therefore, FM stations cannot be received
at the great distances possible with AM
reception.
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
Multipath noise
Since FM signals can be reflected by
obstructions, it is possible to receive both
the direct signal and the reflected signal at
the same time. This causes a slight delay
in reception and may be heard as a broken
sound or a distortion. This problem may
also be encountered when in close
proximity to the transmitter.Flutter/Skip noise
Signals from an FM transmitter move in
straight lines and become weak in valleys
between tall buildings, mountains, and
other obstacles. When a vehicle passes
through such an area, the reception
conditions may change suddenly,
resulting in annoying noise.
Weak signal noise
In suburban areas, broadcast signals
become weak because of distance from
the transmitter. Reception in such fringe
areas is characterized by sound breakup.
Ionosphere
100—200 km (60—120 miles)
FM wave
FM wave AM wave
Direct
Reflected wave
J07R_8R09_EA_02G_Edition4.book Page 11 Monday, February 3, 2003 1:16 PM

6-14
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G
•When inserting the MD, make sure the
MD label is facing up, and the MD is
oriented to the insertion slot in the
direction of the arrow. If not inserted
correctly, the MD will be ejected, or
may remain stuck in the MD deck.
• Do not touch the internal part of the
MD. If the MD shutter is slid open for
no reason, it may be broken.
• Store MDs in their cases and away
from direct sunlight.
• Do not insert fingers or foreign objects
in the MD insertion slot as it could
damage the MD deck.

Operating Tips for CD Player/In-
Dash CD Changer
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or optical
components (prism and lens) in the CD
player/changer may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded
optical components will clear naturally in
about an hour. Wait for normal operation
to return before attempting to use the unit.
Handling the CD player/In-dash CD
changer
The following precautions should be
observed.
• Do not spill any liquid on the audio
system.
• Do not insert any objects, other than
CDs, into the slot.
J07R_8R09_EA_02G_Edition4.book Page 14 Monday, February 3, 2003 1:16 PM

6-23
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G
Changing the display mode
The display on the unit can be changed by
pressing the clock button ( ). This
alternates the display between time and
audio. When the clock mode has been
selected, the time will be displayed.
NOTE
If audio operation is selected while the
time mode is on, the selected audio
mode will be displayed for 10 seconds,
then the display will revert to the time
mode.
J07R_8R09_EA_02G_Edition4.book Page 23 Monday, February 3, 2003 1:16 PM

6-32
Interior Comfort
Au di o S ys t em
Form No. 8R09-EA-02G

Operating the In-Dash CD Changer
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "In" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 5 seconds
after the beep is heard.
3. When "In" is displayed, insert the CD.
Display CD slot
Disc-in indicator
CD ejectbutton
CD play button
Random button
Repeat button
Disc up button Scan
button
Fast-forward
button
Reverse button
Track up
button
Track down
button
Disc down
button
Load button
Power/Volume knob
Channel preset buttons
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume knob and the load
button ( ) for about 2 seconds will
turn this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
J07R_8R09_EA_02G_Edition4.book Page 32 Monday, February 3, 2003 1:16 PM