2003 MAZDA MODEL MPV maintenance schedule

8-10
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
5. Pull it out again and examine the level.
It’s OK between MIN and MAX.
But if it’s near or below MIN, add
enough oil to bring the level to MAX.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.Changing engine oil
1. Warm up the engine for a few minutes
and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil
into a suitable container.
3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the
MAX mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the
drain plug for leaks.
7. Turn it off and wait 5 minutes for the
oil to return to the oil pan. Don’t add engine oil over MAX. This
may cause engine damage.
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Remove oil splatter from the exhaust
manifold, the exhaust pipe and the
shield. Oil left on these areas will
smoke when the engine is running.
CAUTION
WARNING
CAUTION
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
Tighten
Loosen
Front
Drain plug
J16L_8R21-EA-02G.book Page 10 Saturday, June 8, 2002 11:16 AM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
If it’s at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.

Changing Coolant (Without Rear
Heater)
Change coolant according to Scheduled
Maintenance (page 8-3).For mixture percentage:
To change coolant
1. Remove the cooling system cap. Radiator coolant will damage paint.
Rinse it off quickly.
•Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant’s effectiveness.
•Don’t add only water. Always add a
proper coolant mixture.
•The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
•DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
•Don’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
CAUTION
CAUTION
ProtectionVo l u m e
Antifreeze
solutionWa t e r
Above -16°C (3°F) 35% 65%
Above -26°C (-15°F) 45% 55%
Above -40°C (-40°F) 55% 45%
Removing the Cooling System Cap:
Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you’re sure all the pressure is
gone, press down on the cap—still
using a cloth—turn the cap, and
remove it.
WARNING
F
L
Tighten Loosen
TightenLoosen
J16L_8R21-EA-02G.book Page 12 Saturday, June 8, 2002 11:16 AM

8-13
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
2. Only when the engine is cool, remove
the radiator drain plug and drain the
coolant into a suitable container.
3. Flush out the system with running
water.
4. Drain the system completely. Insert
and tighten the plug. Add as much
ethylene-glycol-based coolant and
water as necessary to provide freezing
and corrosion protection.
5. In extremely cold climates, add the
amount recommended in the coolant
manufacturer’s instructions.
6. Run the engine at idle with the cooling
system cap off. Slowly add additional
coolant if necessary.
7. At this point, wait until the engine
reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
8. Install the cooling system cap. Inspect
all connections for leaks. Inspect the
level in the coolant reservoir one more
time.

Changing Coolant (With Rear
Heater)
Have an Authorized Mazda Dealer change
the coolant according to the Scheduled
Maintenance (page 8-3).

Inspecting Brake Fluid Level
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake linings. If it
is excessively low, have the brake system
inspected by an Authorized Mazda
Dealer.
Brake Fluid
J16L_8R21-EA-02G.book Page 13 Saturday, June 8, 2002 11:16 AM

8-18
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
2. Separate the air cleaner housing and
remove the filter.
3. Wipe inside the air cleaner housing
with a damp cloth.
4. Clean or replace the filter.
5. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3).Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
Air filterAir cleaner housing
Wiper Blades
Hot waxes applied by automatic car
washes have been known to affect the
cleanability of windows.
To prevent damage to the wiper blades,
don’t use gasoline, kerosene, paint
thinner, or other solvents on or near
them.
CAUTION
CAUTION
J16L_8R21-EA-02G.book Page 18 Saturday, June 8, 2002 11:16 AM

11-4
Index
Form No. 8R21-EA-02G
H
Hazard Warning Flasher .................. 5-37
Hazardous Driving
............................. 4-8
Headlights
Control
...................................... 5-32
Flashing
.................................... 5-32
High-low beams
........................ 5-32
On reminder
.............................. 5-32
Hood Release
................................... 3-24
Horn
................................................. 5-37
I
Ignition
Keys
............................................ 3-2
Switch
......................................... 5-2
Illuminated Entry System
................ 6-41
Immobilizer System
......................... 3-27
Indicator Lights
................................ 5-23
Cruise set
.................................. 5-30
Headlight high-beam
................ 5-29
O/D OFF
................................... 5-29
Security
..................................... 5-29
Shift position
............................ 5-30
TCS
........................................... 5-30
TCS OFF
.................................. 5-30
Instrument Cluster
........................... 5-19
Interior Care
..................................... 8-43
Interior Lights
.................................. 6-41
J
Jump-Starting ................................... 7-17
K
Keyless Entry System ........................ 3-3
Keys
................................................... 3-2
L
Label Information ............................ 10-2
Lane-Change Signals
....................... 5-33
Liftgate
............................................. 3-18
Light Bulbs
Replacement
.............................. 8-27
Specifications
............................ 10-6
Lighter
.............................................. 6-44
Lighting Control
............................... 5-32
Lubricant Quality
............................. 10-4
Luggage Compartment Light
........... 6-43
M
Maintenance
Introduction
................................. 8-2
Owner maintenance
precautions
.................................. 8-7
Owner maintenance schedule
..... 8-6
Scheduled
.................................... 8-3
Map Lights
....................................... 6-43
Meters and Gauges
........................... 5-19
Mirrors
Outside mirrors
......................... 3-31
Rearview mirror
........................ 3-32
Money-Saving Suggestions
................ 4-7
O
Odometer and Trip Meter ................ 5-20
Outside Mirrors
................................ 3-31
Overhead Console
............................ 6-48
Overhead Lights
............................... 6-42
Overheating
...................................... 7-15
Overloading
...................................... 4-11
J16L_8R21-EA-02G.book Page 4 Saturday, June 8, 2002 11:16 AM