2003 MAZDA MODEL 6 warning light

5-35
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I

TCS Indicator Light
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position. If the TCS is
operating, the indicator light flashes.
If the light stays on, the TCS may have a
malfunction and it may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.

TCS OFF Indicator Light
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position.
It also comes on when the TCS OFF
switch is pressed and TCS is switched off.
If the light stays on when the TCS is not
switched off, take your vehicle to an
Authorized Mazda Dealer. The TCS may
have a malfunction.
NOTE
•
In addition to the indicator light
flashing, a slight lugging sound will
come from the engine. This
indicates that the TCS is operating
properly.
•
On slippery surfaces, such as fresh
snow, it will be impossible to
achieve high rpm when the TCS is
on.
NOTE
After starting the engine when the
coolant temperature is extremely low,
the TCS is automatically turned off. At
this time, the TCS OFF indicator light
will remain on, but this does not
indicate an abnormality. After the
engine has warmed, TCS will resume
normal operation and the indicator
light will go out.
shuseizumi_J56J_8R29_EA_02I.book Page 35 Wednesday, October 16, 2002 9:51 AM

5-36
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I

Cruise Main Indicator Light
This light comes on when the ON/OFF
switch is pressed and the cruise control
system is activated.

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Light-On Indicator Light (Black-
out meter)
This indicator light comes on when the
exterior lights are on.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.
Beeps
shuseizumi_J56J_8R29_EA_02I.book Page 36 Wednesday, October 16, 2002 9:51 AM

5-39
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn the front fog lights on, rotate the
fog light switch to the position.
The headlight switch must be in the
position to turn on the front fog lights.
To turn them off, rotate the fog light
switch to the or OFF position or turn
the headlight switch to the OFF position.The ignition switch must be in the ON
position.
Fog Lights
NOTE
The fog lights will turn off when the
headlights are set at high beam.
Fog light switch
Windshield Wipers and
Wa s h e r
Frozen Washer Fluid:Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected from motor breakdown,
overheating and possible fire by a
circuit breaker. This mechanism will
automatically stop operation of the
blades, but only for about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 39 Wednesday, October 16, 2002 9:51 AM

5-42
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
To sound the horn, press around the
mark of the steering wheel.The hazard warning lights should always
be used when you stop on or near a
roadway.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning switch and all
four turn signals will flash at once.
HornHazard Warning Flasher
NOTE
•
The turn signals don’t work when
the hazard warning lights are on.
•
Check local regulations about the
use of hazard warning lights while
the vehicle is being towed. They
may forbid it.
Hazard warning flasher switch
shuseizumi_J56J_8R29_EA_02I.book Page 42 Wednesday, October 16, 2002 9:51 AM

5-43
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
The HomeLink system replaces up to 3
hand-held transmitters with a single built-
in component in the auto-dimming mirror.
Pressing the HomeLink button on the
auto-dimming mirror activates garage
doors, gates and other devices
surrounding your home.
HomeLink Wireless
Control System
HomeLink buttonIndicator light
Safety Stop and Reverse Feature:Using the HomeLink system with any
garage door opener that lacks the
safety stop and reverse feature as
required by federal safety standards is
dangerous. (This includes garage
doors manufactured before April 1,
1982.)
Using these garage door openers can
increase the risk of serious injury or
death. Call Johnson Controls, Inc.
number: 1.800.355.3515 or visit
www.homelink.com for further
information. If you are unable to
make contact with Johnson Controls,
Inc., consult an Authorized Mazda
Dealer.
Safety While Programming or
Operating HomeLink System:Programming or operating the
HomeLink system without verifying
the safety of areas surrounding
garage doors and gates is dangerous
and could result in an unexpected
accident and serious injury if
someone were to be hit. Always check
the areas surrounding garage doors
and gates for people or obstructions
before programming or during
operation of the HomeLink system.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 43 Wednesday, October 16, 2002 9:51 AM

6-9
Interior Comfort
Climate Control System
Form No. 8R29-EA-02I

Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.

Windshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
NOTE
•
When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector to the
position, then set the fan control dial
to the position 4.
•
If warmer air is desired at floor
level, set the mode selector dial at
the position and adjust the
temperature control dial to maintain
maximum comfort.
•
The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Fo g g y Wi n d s h i e l d :Using the position with the
temperature control set to the cold
position will cause the outside of the
glass to fog up. Your vision will be
hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
NOTE
•
For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
•
If warm air is desired at the floor,
set the mode selector dial to the
position.
•
In the or position, air
conditioning is automatically turned
on to defrost the windshield quickly
(however, the indicator light does
not illuminate) and the
position is automatically selected.
The air intake selector switch
cannot be changed to the
position.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 9 Wednesday, October 16, 2002 9:51 AM

6-14
Interior Comfort
Climate Control System
Form No. 8R29-EA-02I

Windshield Defrosting and
Defogging
Press the windshield defroster switch.
In this position, the outside air position is
automatically selected, and the air
conditioner automatically turned on
(however, the indicator light does not
illuminate). The air conditioner will direct
dehumidified air to the front windshield
and side windows (page 6-4). Airflow
amount will be increased.
To turn off the system press the
windshield defroster switch again.
NOTE
•
First set the temperature to 25.0°
C
(77.0°
F), then adjust to the desired
temperature.
•
Setting the temperature to
maximum high or low will not
provide the desired temperature at a
faster rate.
•
To prevent cool air blowing from
the vents when heating right after
starting the engine, the amount of
airflow is reduced until the air
warms up.Foggy Windshield:Using the position with the
temperature control set to the cold
position will cause the outside of the
glass to fog up. Your vision will be
hampered, which could lead to a
serious accident. Set the temperature
control to hot or warm position when
using the position.
NOTE
Use the temperature control dial to
increase the air flow temperature and
defog the glass more quickly.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 14 Wednesday, October 16, 2002 9:51 AM

6-52
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I

Overhead Console
This console box is designed to store
eyeglasses or other accessories. Push and
release to open.

Storage Pocket
To open, push the release catch down and
pull the lid downward.

Center Box with Lid
To use, pull the knob, and the lid opens
automatically.
Storage Compartments
Open Storage Boxes:Driving with the storage boxes open is
dangerous. To reduce the possibility
of injury in an accident or a sudden
stop, keep the storage boxes closed
when driving.
In hot weather, don’t leave
combustible materials or objects which
will deform in extreme heat such as
lighters and glasses in the vehicle.
WARNING
CAUTION
Knob
shuseizumi_J56J_8R29_EA_02I.book Page 52 Wednesday, October 16, 2002 9:51 AM