2003 MAZDA MODEL 6 Exhaust

8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8R29-EA-02I
I: Inspect and repair, clean, adjust, or replace if necessary.
L: Lubricate
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if installed)Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Brake lines, hoses and connections
II
Brake and clutch fluid level
IIIIIIIIIIII
Disc brakes
IIII
Tire inflation pressure and tire wear
IIIIIIIIIIII
Steering operation and linkages
II
Power steering fluid level
IIIIIIIIIIII
Front suspension ball joints
II
Driveshaft dust boots
II
Bolts and nuts on chassis and body
IIII
Exhaust system heat shields
II
All locks and hinges
LLLLLLLLLLLL
Washer fluid level
IIIIIIIIIIII
Cabin air filter
Replace every 40,000km (25,000miles) or 24 months
shuseizumi_J56J_8R29_EA_02I.book Page 6 Wednesday, October 16, 2002 9:51 AM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
5. Pull it out again and examine the level.
It’s OK between MIN and MAX.
But if it’s near or below MIN, add
enough oil to bring the level to MAX.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Don’t add engine oil over MAX. This
may cause engine damage.
Full
OK
Low 3.0-liter engine
CAUTION
Handling Used Engine Oil:Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Remove any oil splatter from the
exhaust manifold, the exhaust pipe and
the shield. Oil left on these areas will
smoke when the engine is running.
WARNING
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 11 Wednesday, October 16, 2002 9:51 AM

8-44
Maintenance and Care
Appearance Care
Form No. 8R29-EA-02I

Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.

Bright-Metal Maintenance
•
Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
•
To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
•
During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.

Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.

The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting. If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
Don’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
CAUTION
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 44 Wednesday, October 16, 2002 9:51 AM

9-4
Customer Information
Customer Assistance
Form No. 8R29-EA-02I
The Department, in cooperation with the local Mazda Service Representative, will review
the case to determine if everything possible has been done to ensure your satisfaction.
Please recognize that the resolution of service problems in most cases requires the use of
your Mazda dealer’s service facilities, personnel and equipment. We urge you to follow the
above three steps in sequence therefore for most effective results.

Mediation/Arbitration Program
Occasionally a customer concern cannot be resolved through Mazda’s Customer
Satisfaction Program. If after exhausting the procedures in this manual your concern is still
not resolved, you have another option.
Mazda Canada Inc. participates in an arbitration program administered by the Canadian
Motor Vehicle Arbitration Plan (CAMVAP). CAMVAP will advise you about how your
concern may be reviewed and resolved by an independent third party through binding
arbitration.
Your complete satisfaction is the goal of Mazda Canada Inc. and our dealers.
Mazda’s participation in CAMVAP makes a valuable contribution to our achieving that
goal. There is no charge for using CAMVAP. CAMVAP results are fast, fair and final as the
award is binding on both you and Mazda Canada Inc.

Canadian Motor Vehicle Arbitration Plan (CAMVAP)
If a specific item of concern arises, where a solution cannot be reached between an owner,
Mazda, and/or one of it’s dealers (that all parties cannot agree upon), the owner may wish
to use the services offered by the Canadian Motor Vehicle
Arbitration Plan (CAMVAP).
CAMVAP uses the services of Provincial Administrators to assist consumers in scheduling
and preparing for their arbitration hearings. However, before you can proceed with
CAMVAP you must follow your Mazda dispute resolution process as outlined previously.
CAMVAP is fully implemented in all provinces and territories.
Consumers wishing to obtain further information about the Program can obtain an
information booklet from your dealer, the Provincial Administrator or the Canadian Motor
Vehicle Arbitration Plan Office at the following address or telephone number.
Canadian Motor Vehicle Arbitration Office
235 Yorkland Boulevard, suite 300
North York, Ontario
M2J 4Y8
1 (800) 207-0685
shuseizumi_J56J_8R29_EA_02I.book Page 4 Wednesday, October 16, 2002 9:51 AM

11-3
Index
Form No. 8R29-EA-02I
C
Courtesy Lights ................................ 6-45
Cruise Control
.................................. 5-17
Cup Holder
....................................... 6-50
Customer Assistance
.......................... 9-2
D
Dashboard Illumination ................... 5-26
Daytime Running Lights
.................. 5-38
Defroster
Rear window
............................. 5-41
Dimensions
...................................... 10-4
Door Locks
......................................... 3-7
Driving In Flooded Area
.................... 4-9
Driving Tips
....................................... 4-6
Automatic transaxle
.................. 5-16
Break-in
...................................... 4-6
Driving in flooded area
............... 4-9
Hazardous driving
....................... 4-7
Money-saving suggestions
.......... 4-6
Rocking the vehicle
.................... 4-7
Winter driving
............................. 4-8
E
Emergency Starting .......................... 7-14
Flooded engine
.......................... 7-14
Jump-starting
............................ 7-14
Push-starting
............................. 7-16
Emergency Towing
.......................... 7-17
Emission Control System
................... 4-3
Engine
Coolant
...................................... 8-13
Exhaust gas
................................. 4-4
Hood release
............................. 3-17
Oil
............................................. 8-10
Overheating
............................... 7-12
Starting
........................................ 5-3
E
Engine Compartment Overview .........8-9
Engine Coolant
Overheating
...............................7-12
Engine Coolant Temperature
Gauge
...............................................5-25
Exhaust Gas
........................................4-4
Exterior Care
....................................8-42
F
Flasher
Hazard warning
.........................5-42
Headlights
.................................5-37
Flat Tire
..............................................7-3
Changing
.....................................7-5
Spare tire and tool storage
...........7-3
Fluids
Classification
.............................10-3
Owner maintenance
.....................8-7
Fog Lights
........................................5-39
Foot Brake
..........................................5-4
Front seats
..........................................2-2
Fuel
Filler lid and cap
.......................3-16
Gauge
........................................5-26
Requirements
..............................4-2
Tank capacity
............................10-4
Fuses
.................................................8-35
Panel description
.......................8-37
Replacement
..............................8-35
G
Gauges ..............................................5-23
Glove Box
........................................6-53
shuseizumi_J56J_8R29_EA_02I.book Page 3 Wednesday, October 16, 2002 9:51 AM