2003 Lexus GX470 wheel

IN CASE OF AN EMERGENCY
365
Make sure to set the jack properly in the jack point.
Raising the vehicle with jack improperly positioned
will damage the vehicle or may allow the vehicle to fall
off the jack and cause personal injury.
 Never get under the vehicle when the vehicle is
supported by the jack alone.
 Use the jack only for lifting your vehicle during wheel
changing.
 Do not raise the vehicle with someone in the vehicle.
 When raising the vehicle, do not place any objects on
top of or underneath the jack.
 Raise the vehicle only high enough to remove and
change the tire.
NOTICE
Do not continue driving with a deflated tire. Driving
even a short distance can damage a tire and wheel
beyond repair.
 When jacking up or installing tire chains, be sure to
turn off the rear height control air suspension with
the “HEIGHT CONTROL OFF” switch and stop the
engine. Otherwise, the vehicle height may change
because of the automatic leveling function resulting
in accident.
40PY040
 1 Jack

2 Spare tire

3 Tool tray
1. Get the tool, jack and spare tire.
To remove the tool tray, turn the knob counterclockwise and
open the cover, then pull the tray out.

IN CASE OF AN EMERGENCY
367
40PY041
 1 Lower2 Raise3 Cloth To remove the spare tire:
1. Open the back door and remove the spare tire carrier lid
using a flat−
bladed screwdriver.
2. Insert the end of the jack handle extension into the lowering
screw and put a cloth between the jack handle extension and
rear bumper for protecting the bumper surface.
3. Turn the jack handle counterclockwise with the handle,
making sure the handle remains firmly fitted onto the jack
handle extension.
4. After the tire is lowered completely to the ground, remove
the holding bracket.
When storing the spare tire, put it in place with the outer side
of the wheel facing up. Then secure the tire, taking care that
the tire goes straight up without catching on any other part, to
prevent it from flying forward during a collision or sudden
braking.
NOTICE
Tighten the spare tire clamp bolt to hold the spare wheel
carrier by the hook securely.

IN CASE OF AN EMERGENCY
368
2. Block the wheel diagonally opposite the flat tire to keep
the vehicle from rolling when it is jacked up.
When blocking the wheel, place a wheel block in front of one
of the front wheels or behind one of the rear wheels.3. Remove the wheel ornament.
Pry off the wheel ornament, using the beveled end of the wheel
ornament remover as shown.
CAUTION
Do not try to pull off the ornament by hand. Take due
care in handling the ornament to avoid unexpected
personal injury.

IN CASE OF AN EMERGENCY
369
4. Loosen all the wheel nuts.
Always loosen the wheel nuts before raising the vehicle.
Turn the wheel nuts counterclockwise to loosen them. To get
maximum leverage, fit the wrench to the nut so that the handle
is on the right side, as shown above. Grab the wrench near the
end of the handle and pull up on the handle. Be careful that the
wrench does not slip off the nut.
Do not remove the nuts yet − just unscrew them about one −half
turn.
CAUTION
Never use oil or grease on the bolts or nuts. The nuts
may loose and the wheels may fall off, which could
cause a serious accident.
 Front (under the frame side rail)
 Rear (under the rear axle housing)
5. Position the jack at the jack points as shown.
Make sure the jack is positioned on a level and solid surface.

IN CASE OF AN EMERGENCY
371
6. After making sure no one is in the vehicle, raise it high
enough so that the spare tire can be installed.
Allow for the fact that you need more ground clearance when
putting on the spare tire than when removing the flat tire.
To raise the vehicle, insert the jack handle extension into the
jack (it is a loose fit) and turn it clockwise with the handle,
making sure the handle remains firmly fitted onto the jack
handle extension. As the jack touches the vehicle and begins
to lift, double− check that it is properly positioned.
CAUTION
Never get under the vehicle when the vehicle is
supported by the jack alone.
7. Remove the wheel nuts and remove the flat tire.
Lift the flat tire straight off and put it aside.
Roll the spare wheel into position and align the holes in the
wheel with the bolts. Then lift up the wheel and get at least the
top bolt started through its hole. Wiggle the tire and press it
back over the other bolts.

IN CASE OF AN EMERGENCY
372
Before putting on the wheel, remove any corrosion on the
mounting surfaces with a wire brush or such. Installation of
wheels without good metal−to−metal contact at the mounting
surface can cause wheel nuts to loosen and eventually cause
a wheel to come off while driving.8. Reinstall all the wheel nuts finger tight.
Reinstall the wheel nuts and tighten them as much as you can
by hand. Press the tire back and see if you can tighten them
more.
CAUTION
Never use oil or grease on the bolts or nuts. Doing so
may lead to overtightening the nuts and damaging the
bolts. The nuts may loose and the wheels may fall off,
which could cause a serious accident. If there is oil or
grease on any bolt or nut, clean it.

IN CASE OF AN EMERGENCY
373
9. Lower the vehicle completely and tighten the wheel
nuts.
To lower the vehicle, turn the jack handle extension
counterclockwise with the handle, making sure the handle
remains firmly fitted onto the jack handle extension.
Use only the wheel nut wrench to tighten the nuts. Do not use
other tools or any additional leverage other than your hands,
such as a hammer, pipe or your foot. Make sure the wrench
is securely engaged over the nut.
Tighten each nut a little at a time in the order shown. Repeat
the process until all the nuts are tight.
CAUTION
When lowering the vehicle, make sure all portions of
your body and all other persons around will not be
injured as the vehicle is lowered to the ground.
 Have the wheel nuts tightened with torque wrench to
112 N·m (11.5 kgf·m, 83 ft·lbf), as soon as possible
after changing wheels. Otherwise, the nuts may
loosen and the wheels may fall off, which could cause
a serious accident.

IN CASE OF AN EMERGENCY
374
10. Reinstall the wheel ornament.
Put the wheel ornament into position and then tap it firmly with
the side or heel of your hand to snap it into place.
CAUTION
Take due care in handling the ornament to avoid
unexpected personal injury.
11. After changing the wheel, check the air pressure of the
replaced tire. Stow all the tools, jack and flat tire securely.
If the pressure of the replaced tire is low, drive slowly to the
nearest service station and fill to the correct pressure.
Do not forget to reinstall the tire valve cap as dirt and moisture
could get into the valve core and possible cause air leakage.
If the cap is missing, put a new one on as soon as possible.
This is the same procedure for changing or rotating your tires.
CAUTION
Before driving, make sure all the tools, jack and flat tire
are securely in place in their storage location to reduce
the possibility of personal injury during a collision or
sudden braking.