2003 Lexus GX470 ECU

Finish
This device complies with FCC Rules part 15.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference that
may be received, including interference that may
cause undesired operation. WARNING: This trans-
mitter has been tested and complies with FCC
and DOC/MDC rules. Changes or modifications
not expressly approved by the party responsible
for compliance could void the user’s authority to
operate the device.
FCC ID: CB2070NHL3
CANADA: 279 103 1936A
INTERIOR EQUIPMENT
73
(c) Erasing the entire HomeLink memory (all
three programs)
To erase all previously programmed codes at one time, press
and hold down the 2 outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored
in the HomeLink
 memory.
CAUTION
 When programming the HomeLink Universal
Transceiver, you may be operating a garage door or
other device. Make sure people and objects are out
of the way of the garage door or other device to
prevent potential harm or damage.
 Do not use this HomeLink
 Universal Transceiver
with any garage door opener that lacks the safety
stop and reverse feature as required by federal safety
standards. (This includes any garage door opener
model manufactured before April 1, 1982.) A garage
door opener which cannot detect an object (signaling
the door to stop and reverse), does not meet current
federal safety standards. Using a garage door opener
without these features increases risk of serious
injury or death.
CUP HOLDERS
Front
 In front of the rear console box
To use the cup holder, push the cup holder lid.
The cup holder is designed for holding cups or drink −cans
securely.
The cup holder can be adjusted to the size of the cups by
changing the separator position or moving the separator arms.
You can use it as an accessory box by removing the separator
inside.

Finish
INTERIOR EQUIPMENT
74
 In the rear console box
To use the cup holder, open the rear console box and pull
down the cup holder.
The cup holder is designed for holding cups or drink −cans
securely.
CAUTION
 Do not place anything else other than cups or
drinkcans in the cup holder, as such items may be
thrown about in the compartment and possibly injure
people in the vehicle during sudden braking or in an
accident.
 To reduce the chance of injury in case of an accident
or sudden stop while driving, keep the cup holder
closed when not in use.
Rear
 Second seat armrest
To use the cup holder, pull down the second seat armrest
and push the cup holder portion of the armrest.
The cup holder is designed for holding cups or drink −cans
securely.

Finish
INTERIOR EQUIPMENT
77
Firstaid kit holder
 1 To loosen2 To tighten
This auxiliary box is equipped with a belt to hold the
firstaid kit. To loosen or tighten the belt, do as shown
above.
Although the first−aid kit itself is not included as original
equipment, this auxiliary box can be used to store the first aid
kit.
Make sure the first −aid kit is securely held.
FLOOR MAT
Use a floor mat of the correct size.
If the floor carpet and floor mat have 2 holes, then they are
designed for use with locking clips. Fix the floor mat with
locking clips into the holes in the floor carpet.

Finish
INTERIOR EQUIPMENT
78
CAUTION
Make sure the floor mat is properly placed on the floor
carpet. If the floor mat slips and interferes with the
movement of the pedals during driving, it may cause an
accident.
WARNING REFLECTOR HOLDER
 1 To disengage 2 To engage
This belt is designed to hold the warning reflector. To
disengage or engage the belt, do as shown above.
Although the warning reflector itself is not included as original
equipment, this auxiliary box can be used to store the warning
reflector.
Make sure the warning reflector is securely held.

Finish
INTERIOR EQUIPMENT
80
Removing luggage cover
To remove the luggage cover, retract and release the both
ends, and lift it out.
After remove the luggage cover, place it somewhere other than
the passenger compartment. This will prevent passengers
from injury in the event of a sudden stop or accident.
When installing the luggage cover, keep the “TOP” mark
of the luggage cover ends upward.
TIEDOWN HOOKS
To secure your luggage, use the tiedown hooks as shown
above.
See “Luggage stowage precautions” on page 81 for
precautions when loading luggage.
NOTICE
Do not use the third seat anchors instead of the
tiedown hooks.

Finish
INTERIOR EQUIPMENT
81
LUGGAGE STOWAGEPRECAUTIONS
When stowing luggage or cargo in or on the vehicle,
observe the following:
Put luggage or cargo in the luggage compartment when at
all possible. Be sure all items are secured in place.
 Be careful to keep the vehicle level. Placing the weight as
far forward as possible helps maintain vehicle balance.
 For better fuel economy, do not carry unnecessary weight.
CAUTION
To prevent luggage or packages from sliding forward
during braking, do not stack anything in the luggage
compartment higher than the seatbacks. Keep
luggage or packages low, as close to the floor as
possible.
 Never allow anyone to ride in the luggage
compartment. It is not designed for passengers.
They should ride in their seats with their seat belts
properly fastened. Otherwise, they are much more
likely to suffer serious bodily injury, in the event of
sudden braking or a collision.
Do not place anything on the luggage cover. Such
items may be thrown about and possibly injury
people in the vehicle during sudden braking or an
accident.
 Do not drive with objects left on top of the instrument
panel. They may interfere with the driver’s field of
view. Or they may move during sharp vehicle
acceleration or turning, and impair the driver’s
control of the vehicle. In an accident they may injure
the vehicle occupants.
NOTICE
Do not load the vehicle beyond the vehicle capacity
weight specified on the tire pressure label.

EXTERIOR EQUIPMENT
83
HOOD
1. To open the hood, pull the hood lock release lever under
the instrument panel. The hood will spring up slightly.
2. Insert your fingers under the hood, push up the
auxiliary catch lever and lift the hood.
Before closing the hood, check to see that you have not
forgotten any tools, rags, etc. Then lower the hood and make
sure it locks.
CAUTION
Before driving, be sure that the hood is closed and
securely locked. Otherwise, the hood may open
unexpectedly while driving and an accident may occur.

EXTERIOR EQUIPMENT
86When installing the cap, turn the cap clockwise until you
hear one click. When you hear the click, the cap is fully
closed.
CAUTION

Make sure the cap is installed securely to prevent fuel
spillage in case of an accident.
 Use only a genuine Lexus fuel tank cap for
replacement. It is designed to regulate fuel tank
pressure.
NOTICE
Observe the following precautions. Otherwise, the cap
could be damaged or become hard to open.
Apply force only in the turning direction to the cap.
Do not pull or pry it.
 Do not tighten the cap further after you hear one click
when installing.
MOON ROOF
 1 Open2 Close
To slide open the moon roof, push the switch on the
“SLIDE OPEN” side for about 1 second. The moon roof
will fully open. To stop partway, push the same side or
“TILT UP” side briefly.
The sunshade can be opened or closed manually. However,
if you open the moon roof, the sunshade will be opened with
the moon roof.
When the moon roof is fully opened, the wind deflector raises
to reduce the entering of the strong wind. The angle of the
deflector is changed according to the vehicle speed.
To close the moon roof, push the switch on the “TILT UP”
side for about 1 second. The moon roof will fully close.
To stop partway, push the same side or “SLIDE OPEN”
side briefly.