2003 INFINITI G35 engine

ENGINE Model VQ35DE
Type Gasoline, 4-cycle
Cylinder arrangement 6-cylinder, V-slanted at 60É
Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4)
Displacement cu in (cm 3
) 213.45 (3,498)
Firing order 1-2-3-4-5-6*
Idle speed rpm
See the emission control label on
the underside of the hood.Ignition timing (B.T.D.C.) degree/rpm
CO percentage at idle speed [No air] %
Spark plug Standard PLFR5A-11
Service option PLFR4A-11, PLFR6A-11
Spark plug gap (Normal) in (mm) 0.043 (1.1)
Camshaft operation Timing chain The spark ignition system of this vehicle
meets all requirements of the Canadian
Interference-Causing Equipment Regula-
tions. TI0001-A
SPECIFICATIONS
Technical and consumer information
10-7
Z 02.7.29/V35-D/V5.0
X

When planning to travel in another country,
you should first find out if the fuel available is
suitable for your vehicle's engine.
Using fuel with too low an octane rating may
cause engine damage. All gasoline vehicles
must be operated with unleaded engine gaso-
line. Therefore, avoid taking your vehicle to
areas where appropriate fuel is not available.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ.
When any vehicle is to be taken into an-
other country, state, province or district
and registered, its modifications, transpor-
tation, and registration are the responsibil-
ity of the user. INFINITI is not responsible
for any inconvenience that may result.
VEHICLE IDENTIFICATION
NUMBER (VIN) PLATE The vehicle identification number plate is at-
tached as shown. This number is the identifi-
cation for your vehicle and is used in the
vehicle registration.
VEHICLE IDENTIFICATION
NUMBER (Chassis number) The number is stamped as shown. STI0038 STI0302
WHEN TRAVELING OR
REGISTERING YOUR VEHICLE IN
ANOTHER COUNTRY VEHICLE IDENTIFICATION
Technical and consumer information
10-9
Z 02.7.29/V35-D/V5.0
X

ENGINE SERIAL NUMBER The number is stamped on the engine as
shown.
F.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Standards
(F.M.V.S.S.) certification label is affixed as
shown. This label contains valuable vehicle
information, such as: Gross Vehicle Weight
Ratings (GVWR), Gross Axle Weight Rating
(GAWR), month and year of manufacture,
Vehicle Identification Number, (VIN), etc. Re-
view it carefully.STI0303 STI0186A STI0330
10-10 Technical and consumer information
Z 02.7.29/V35-D/V5.0
X

ceeded. If GVWR is exceeded, remove
cargo as necessary. If either the front or
rear GAWR is exceeded, shift the load or
remove cargo as necessary.
LOADING TIPS O The GVW must not exceed GVWR or
GAWR as specified on the F.M.V.S.S. cer-
tification label.
O Do not load the front and rear axle to the
GAWR. Doing so will exceed the GVWR.
WARNINGO Properly secure all cargo to help pre-
vent it from sliding or shifting. Do not
place cargo higher than the seat-
backs. In a sudden stop or collision,
unsecured cargo could cause per-
sonal injury.
O Do not load your vehicle any heavier
than the GVWR or the maximum front
and rear GAWRs. If you do, parts on
your vehicle can break, or it can
change the way your vehicle handles.
This could result in loss of control and cause personal injury.
O Overloading can shorten the life of
your vehicle. Failures caused by
overloading are not covered by your
warranty.
Your new vehicle was designed to be used
primarily to carry passengers and cargo. Re-
member that towing a trailer will place addi-
tional loads on your vehicle's engine, drive
train, steering, braking and other systems.
Information on trailer towing ability and the
special equipment required should be ob-
tained from your INFINITI retailer. Your retailer
can obtain an INFINITI Trailer Towing Guide
for you. TI1011M
TOWING A TRAILER
Technical and consumer information
10-15
Z 02.7.29/V35-D/V5.0
X

condition; check for improper tongue load,
overload, worn suspension or other pos-
sible causes of either condition.
O Always secure items in the trailer to prevent
load shifts while driving.
O Be certain your rear view mirrors conform to
all federal, state or local regulations. If not,
install any mirrors required for towing be-
fore driving the vehicle.
Trailer towing tips In order to gain skill and an understanding of
the vehicle's behavior, you should practice
turning, stopping and backing up in an area
which is free from traffic. Steering stability, and
braking performance will be somewhat differ-
ent than under normal driving conditions.
O Always secure items in the trailer to prevent
load shift while driving.
O Avoid abrupt starts, acceleration or stops.
O Avoid sharp turns or lane changes.
O Always drive your vehicle at a moderate
speed.
O Always block the wheels on both vehicle
and trailer when parking. Parking on a
slope is not recommended; however, if you
must do so, and if your vehicle is equipped with automatic transmission, first apply the
parking brake and block the wheels, and
then move the transmission selector lever
into the P (Park) position. If you move the
selector lever to the P (Park) position be-
fore blocking the wheels and applying the
parking brake, the transmission may be
damaged.
O When going down a hill, shift into a lower
gear and use the engine braking effect.
When ascending on a long grade, down-
shift the transmission to a lower gear and
reduce speed to reduce chances of engine
overloading and/or overheating.
O If the engine coolant rises to an extremely
high temperature when the air conditioning
system is on, turn off the air conditioner.
Coolant heat can be additionally vented by
opening the windows, switching the fan
control to high and setting the temperature
control to the HOT position.
O Trailer towing consumes more fuel than
normal circumstances.
O Avoid towing a trailer for the first 500 miles
(800 km).
O Have your vehicle serviced more often than
at intervals specified in the recommended
maintenance schedule. O When making a turn, your trailer wheels will
be closer to the inside of the turn than your
vehicle wheels. To compensate for this,
make a larger than normal turning radius
during the turn.
O Crosswinds and rough roads will adversely
affect vehicle/trailer handling, possibly
causing vehicle sway. When being passed
by larger vehicles, be prepared for possible
changes in crosswinds that could affect
vehicle handling. If swaying does occur,
firmly grip the steering wheel, steer straight
ahead, and immediately (but gradually) re-
duce vehicle speed. This combination will
help stabilize the vehicle. Never increase
speed.
O Be careful when passing other vehicles.
Passing while towing a trailer requires con-
siderably more distance than normal pass-
ing. Remember the length of the trailer
must also pass the other vehicle before you
can safely change lanes.
O To maintain engine braking efficiency and
electrical charging performance, do not use
sixth gear (manual transmission) or fifth
position (automatic transmission).
O Avoid holding the brake pedal down too
long or too frequently such as on long
down-hill sections of road. This could cause
10-18 Technical and consumer information
Z 02.7.29/V35-D/V5.0
X

the brakes to overheat, resulting in reduced
braking efficiency. Shift down and use en-
gine braking.
When towing a trailer, change transmission
oil more frequently.
See ªPeriodic maintenance schedulesº in
the ª9. Maintenanceº section. Shift down
and use engine braking. DOT (Department Of Transportation) Quality
Grades: All passenger car tires must conform
to federal safety requirements in addition to
these grades.
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
Treadwear Treadwear grade is a comparative rating
based on tire wear rate when tested under
controlled conditions on specified government
test courses. For example, a tire graded 150
would wear one and a half (1-1/2) times as well
on the government course as a tire graded
100. However, relative tire performance de-
pends on actual driving conditions, and may
vary significantly from the norm due to varia-
tions in driving habits, service practices and
differences in road characteristics and climate.
Traction AA, A, B and C The traction grades, from highest to lowest,
are AA, A, B, and C. Those grades represent
the tire's ability to stop on wet pavement as
measured under controlled conditions on
specified government test surfaces of asphalt and concrete. A tire marked C may have poor
traction performance.
WARNING The traction grade assigned to your ve-
hicle tires is based on straight-ahead
braking traction tests, and does not in-
clude acceleration, cornering, hydro-
planing, or peak traction characteristics.
Temperature A, B and C Temperature grades are A (the highest), B,
and C. They represent a tire's resistance to
heat build-up, and its ability to dissipate heat
when tested under controlled conditions on a
specified indoor laboratory test wheel. Sus-
tained high temperature can cause tire mate-
rial to degenerate, reducing tire life. Excessive
temperatures can lead to sudden tire failure.
Grade C corresponds to a performance level
which all passenger car tires must meet under
the Federal Motor Vehicle Safety Standard No.
109. Grades A and B represent higher levels of
performance on laboratory test wheels than
the minimum required by law.UNIFORM TIRE QUALITY
GRADING
Technical and consumer information
10-19
Z 02.7.29/V35-D/V5.0
X

If you believe that your vehicle has a defect
which could cause a crash or could cause
injury or death, you should immediately
inform the National Highway Traffic Safety
Administration
(NHTSA) in addition to no-
tifying INFINITI.
If
NHTSA receives similar complaints, it
may open an investigation, and if it finds
that a safety defect exists in a group of
vehicles, it may order a recall and remedy
campaign. However,
NHTSA cannot be-
come involved in individual problems be-
tween you, your retailer, or INFINITI.
To contact
NHTSA , you may call the Auto
Safety Hotline toll-free at 1-888-327-4236.
You may also write to:
NHTSA , U.S. De-
partment of Transportation, Washington,
D.C. 20590. You can also obtain other
information about motor vehicle safety from
the Hotline. You may notify INFINITI by contacting our
Consumer Affairs Department, toll-free, at
1-800-662-6200.
In Hawaii call (808) 836-0888. Due to legal requirements in some states/
areas, your vehicle may be required to be in
what is called the ªready conditionº for an
Inspection/Maintenance (I/M) test of the emis-
sion control system.
The vehicle is set to the ªready conditionº
when it is driven through certain driving pat-
terns. Usually, the ªready conditionº can be
obtained by ordinary usage of the vehicle.
If a powertrain system component is repaired
or the battery is disconnected, the vehicle may
be reset to a not ªready conditionº. Before
taking the I/M test, drive the vehicle through
the following pattern to set the vehicle to the
ready condition. If you cannot or do not want to
perform the driving pattern, an INFINITI re-
tailer can conduct it for you.
WARNING Always drive the vehicle in a safe and
prudent manner according to traffic con-
ditions, and obey all traffic laws.
1. Start the engine. Allow the engine to idle
until the engine coolant temperature gauge
needle points between the C and H (normal
operating temperature). 2. Accelerate the vehicle to 55 MPH (88
km/h), then quickly release the accelerator
pedal completely and keep it released for at
least 6 seconds.
3. Quickly depress the accelerator pedal for a
moment, then drive the vehicle at a speed
of 53 to 60 MPH (86 to 96 km/h) for at least
5 minutes.
4. Stop the vehicle. Leave the engine running.
5. Accelerate the vehicle to 35 MPH (55 km/h)
and maintain the speed for 20 seconds.
6. Repeat steps 4 and 5 at least 3 times.
7. Accelerate the vehicle to 55 MPH (88 km/h)
and maintain the speed for at least 3 min-
utes.
8. Stop the vehicle. Place the automatic trans-
mission selector lever in the ªPº or ªNº
position or the manual transmission shift
lever in the ªNº position.
9. Turn the engine off.
10.Repeat steps 1 through 8 at least one more
time.
If step 1 through 7 is interrupted, repeat the
preceding step. Any safe driving mode is ac-
ceptable between steps. Do not stop the en-
gine until step 7 is completed.REPORTING SAFETY DEFECTS
(US only) READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US
only)
Technical and consumer information
10-21
Z 02.7.29/V35-D/V5.0
X

11 Index A
ABS (Anti-lock brake system) ......................... 5-20
Air bag system, Front (See supplemental front air
bag system) .................................................... 1-17
Air bag warning labels .................................... 1-23
Air bag warning light.............................. 1-23, 2-11
Air cleaner housing filter ................................. 8-16
Air conditioner
Air conditioner operation ............................. 4-3
Air conditioner service ......................... 4-3, 4-6
Air conditioner specification label............ 10-12
Air conditioning system refrigerant and
lubricant recommendations ................ 4-6, 10-6
Dual zone button (if so equipped)............... 4-5
Economical operation (ECON) .................... 4-4
Heater and air conditioner (automatic) ....... 4-3
Microfilter ..................................................... 4-5
Alcohol, drugs and driving ................................ 5-4
Ambient temperature, Air conditioner ............... 4-5
Anchor point locations
Top tether strap ......................................... 1-42
Antenna........................................................... 4-17
Anti-lock Brake System (ABS) ........................ 5-20
Anti-lock brake warning light............................. 2-9
Appearance care
Exterior appearance care ............................ 7-2
Interior appearance care ............................. 7-3
Armrest ............................................................. 1-8 Ashtrays (See cigarette lighter and
ashtray) ........................................................... 2-24
Audible reminders ........................................... 2-13
Audio operation precautions ............................. 4-8
Audio system .................................................... 4-6
Steering audio control ............................... 4-17
Autochanger
Compact Disc (CD) ................................... 4-15
Automatic
Adjusting function (Coupe) ........................ 2-33
Anti-glare inside mirror .............................. 3-17
Automatic transmission fluid (ATF) ............. 8-9
Drive positioner ......................................... 3-19
Driving with automatic transmission .... 5-4, 5-8
Operation (For all door windows or front door
windows).................................................... 2-32
Seat positioner, seat ................................. 3-19
Sunroof ...................................................... 2-33
Transmission selector lever lock
release ....................................................... 5-12
Avoiding collision and rollover .......................... 5-3
B
Battery............................................................. 8-13
Battery saver system................................. 2-18
Battery replacement, (See remote keyless entry
system) ............................................................. 3-8
Before starting the engine ................................ 5-7 Belts (See drive belts) .................................... 8-14
Brake
Anti-lock brake system (ABS) ................... 5-20
Brake and clutch fluid................................ 8-11
Brake booster ............................................ 8-19
Brake fluid ................................................. 8-11
Brake pedal ............................................... 8-18
Brake pedal check..................................... 8-18
Brake system............................................. 5-19
Parking brake check ........................ 5-14, 8-18
Parking brake operation ............................ 5-14
Warning light ............................................... 2-9
Break-in schedule ........................................... 5-17
Bulb check/instrument panel ............................ 2-9
Bulb replacement ............................................ 8-22
C
Cabin air filter ................................................... 4-5
Capacities and recommended fuel/lubricants/
fluid ................................................................. 10-2
Car phone or CB radio ................................... 4-18
Cargo (See vehicle loading information) ........ 2-29
Cargo net ........................................................ 2-29
Cassette player (See audio system) .............. 4-14
Catalytic converter, Three way catalyst............ 5-3
CD care and cleaning ..................................... 4-16
Child restraints ................................................ 1-33
Installation on front passenger seat .......... 1-43
Z 02.7.29/V35-D/V5.0
X