
FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 48
B570A01A-AAT
HOOD RELEASE HOOD RELEASEHOOD RELEASE HOOD RELEASE
HOOD RELEASE
1. Pull the release knob to unlatch the hood.
2. Press the secondary catch lever up and lift
the hood.
3. Hold the hood open with the support rod.
Before closing the hood, return the support rod
to its clip to prevent it from rattling. Lower the
hood until it is about 1 ft. (30 cm) above the
closed position and let it drop. Make sure that
it locks into place.
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:Make sure that the support rod has been Make sure that the support rod has beenMake sure that the support rod has been Make sure that the support rod has been
Make sure that the support rod has been
released prior to closing the hood. released prior to closing the hood.released prior to closing the hood. released prior to closing the hood.
released prior to closing the hood.
WARNING:o Always double check to be sure that the
hood is firmly latched before driving
away. If it is not latched, the hood could
fly open while the vehicle is being driven,
causing a total loss of visibility, which
might result in an accident.
o The support rod must be inserted com-
pletely into the hole provided in the hood
whenever you inspect the engine com-
partment. This will prevent the hood from
falling and possibly injuring you.
o Do not move the vehicle with the hood in
the raised position, as vision is ob-
structed and the hood could fall or be
damaged.
B570A01E
B570B01E
B620A01S-AATFRONT DOOR EDGE WARNING
LIGHT (If Installed)
A red light turns on when the front door is
opened. The purpose of this light is to assist
when you get in or out and also to warn passing
vehicles.
B620A01E

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 50Your vehicle is equipped with a glow-in-the dark
emergency trunk release lever located inside
the trunk. It will glow after the trunk is closed.
When pulled, this lever will release the trunk
latch mechanism and open the trunk.
NOTE:o If a person is locked in the trunk by one's
own will or by another person or by
accident, pull the emergency trunk re-
lease lever on the driver's side of the
inside panel of the trunk. This will open
the trunk lid.
o HYUNDAI recommends that cars be kept
locked and keys be kept out of the reach
of children, and that parents teach their
children about the dangers of playing in
trunks.
WARNING:Parents should teach children about the
emergency trunk release lever in their ve-
hicle and how to open the trunk lid if they are
accidentally locked in the trunk.
B540C01S-AAT
To Unlock Using the Key. To Unlock Using the Key.To Unlock Using the Key. To Unlock Using the Key.
To Unlock Using the Key.
To open the trunk lid, insert the key and turn it
clockwise to unlock. The trunk lid compartment
light illuminates when the trunk lid is opened.
B540C01E-A
B540B02E-AAT
Trunk Lid Emergency Latch Release
B540E01E-A
Pull to open
the trunk
B540A01E-GATTRUNK LID (4 DOOR) TRUNK LID (4 DOOR)TRUNK LID (4 DOOR) TRUNK LID (4 DOOR)
TRUNK LID (4 DOOR)
Remote Trunk Lid Release Remote Trunk Lid ReleaseRemote Trunk Lid Release Remote Trunk Lid Release
Remote Trunk Lid Release
To open the trunk lid without using the key, pull
up the lid release lever.
To close, lower the trunk lid, then press down
on it until it locks. To be sure the trunk lid is
securely fastened, always try to pull it up again.
WARNING: WARNING:WARNING: WARNING:
WARNING:The trunk lid should always be kept com- The trunk lid should always be kept com-The trunk lid should always be kept com- The trunk lid should always be kept com-
The trunk lid should always be kept com-
pletely closed while the vehicle is in motion. pletely closed while the vehicle is in motion.pletely closed while the vehicle is in motion. pletely closed while the vehicle is in motion.
pletely closed while the vehicle is in motion.
If it is left open or ajar, poisonous exhaust If it is left open or ajar, poisonous exhaustIf it is left open or ajar, poisonous exhaust If it is left open or ajar, poisonous exhaust
If it is left open or ajar, poisonous exhaust
gases may enter the car resulting in serious gases may enter the car resulting in seriousgases may enter the car resulting in serious gases may enter the car resulting in serious
gases may enter the car resulting in serious
illness or death to the occupants. See addi- illness or death to the occupants. See addi-illness or death to the occupants. See addi- illness or death to the occupants. See addi-
illness or death to the occupants. See addi-
tional warnings concerning exhaust gases tional warnings concerning exhaust gasestional warnings concerning exhaust gases tional warnings concerning exhaust gases
tional warnings concerning exhaust gases
on page 2-1. on page 2-1.on page 2-1. on page 2-1.
on page 2-1.
B540A01E-A
o oo o
o
Do not "TOP-OFF" after the first nozzle Do not "TOP-OFF" after the first nozzleDo not "TOP-OFF" after the first nozzle Do not "TOP-OFF" after the first nozzle
Do not "TOP-OFF" after the first nozzle
shut off when refueling. shut off when refueling.shut off when refueling. shut off when refueling.
shut off when refueling.

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 51
B580A01L-GATSUN VISOR
B580A01E
Your Hyundai is equipped with sun visors to
give the driver and front passenger either fron-
tal or sideward shade. The sun visors are fitted
on both sides on all models. To reduce glare or
to shut out direct rays of the sun, turn the sun
visor down to block the annoyance. A vanity
mirror is provided on the back of the sun visor
for the driver and front passenger.
NOTE:The Supplemental Restraint System (SRS)
label containing useful information can be
found on the back of each sun visor.
WARNING:Do not place the sun visor in such a manner
that it obscures visibility of the roadway,
traffic or other objects.
Vanity mirror
B800A01E-GATCD Auto Changer (If Installed)
A CD Auto Changer is located in the left side of
the trunk. This system can store up to 8 CDs.
You may select music without changing disks.
First, open the CD Auto Changer door and
insert 8 CDs by taking out the magazine. Then,
push the magazine into the CD Auto Changer.
The CD may be operated with the passenger
compartment audio system controls.
HXD150
B540F01E-GATTAIL GATE (5 DOOR)
Operation From Outside The Vehicle
B540F01E
To open the tail gate, insert the key and turn it
clockwise to unlock.
Then, pull the outside handle toward you.

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 521. Push the lever downward to unlock.
2. Raise or lower the steering wheel to the
desired position.
3. After adjustment, securely tighten the lever
by pulling it upward.
WARNING: WARNING:WARNING: WARNING:
WARNING:Do not attempt to adjust the steering wheel Do not attempt to adjust the steering wheelDo not attempt to adjust the steering wheel Do not attempt to adjust the steering wheel
Do not attempt to adjust the steering wheel
while driving as this may result in loss of while driving as this may result in loss ofwhile driving as this may result in loss of while driving as this may result in loss of
while driving as this may result in loss of
control of the vehicle which may cause control of the vehicle which may causecontrol of the vehicle which may cause control of the vehicle which may cause
control of the vehicle which may cause
serious injury or death. serious injury or death.serious injury or death. serious injury or death.
serious injury or death.
B610A01Y-AAT
HORN HORNHORN HORN
HORN
Press the pad on the steering wheel to sound
the horn.
B610A01E
B660A01E
Main switch
B660A01S-AATCRUISE CONTROL (If Installed)
The cruise control system provides automatic
speed control for your comfort when driving on
B600A01A-AAT
STEERING WHEEL TILT LEVER STEERING WHEEL TILT LEVERSTEERING WHEEL TILT LEVER STEERING WHEEL TILT LEVER
STEERING WHEEL TILT LEVER
(If Installed) (If Installed)(If Installed) (If Installed)
(If Installed)
To Adjust the Steering Wheel: To Adjust the Steering Wheel:To Adjust the Steering Wheel: To Adjust the Steering Wheel:
To Adjust the Steering Wheel:
B600A01E B590A01E-AAT
TICKET HOLDER (If Installed)
HXDOM240
For your convenience, it may be used for
holding a tollgate ticket.

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 58The air conditioning is turned on or off by
pushing the A/C button on the heating/air con-
ditioning control panel.
B730A01FC-GATOperation Tipso To keep dust or unpleasant fumes from
entering the car through the ventilation sys-
tem, temporarily set the air intake control to
"Recirculation". Be sure to return the control
to "Fresh" when the irritation has passed to
keep fresh air in the vehicle. This will help
keep the driver alert and comfortable.
o Air for the heating/cooling system is drawn
in through the grilles just ahead of the wind-
shield. Care should be taken that these are
not blocked by leaves, snow, ice or other
obstructions.
o To prevent interior fog on the windshield, set
the air intake control to the fresh air ( )
position and fan speed to the desired posi-
tion.
B740A01S-AATAIR CONDITIONING SYSTEM
Air Conditioning Switch
B740A01E
B710C01S-AATSIDE VENTILATOR
B710C01E-1
The side ventilators are located on each side
of dashboard. To change the direction of the
air flow, move the knob in the center of the vent
up-and-down and side-to-side. The side vent
knobs control the amount of outside air entering
the vehicle through the side vents. The vents
are opened when the vent knob is moved to the
up position. The vents are closed when the vent
knob is moved to the down position. Keep these
vents clear of leaves and other debris.

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 67
B750B02Y-AATUsing a cellular phone or a two-way
radio
When a cellular phone is used inside the ve-
hicle, noise may be produced from the audio
equipment. This does not mean that something
is wrong with the audio equipment. In such a
case, use the cellular phone at a place as far as
possible from the audio equipment.
CAUTION:When using a communication system such
a cellular phone or a radio set inside the
vehicle, a separate external antenna must
be fitted. When a cellular phone or a radio
set is used with an internal antenna alone, it
may interfere with the vehicle's electrical
system and adversely affect safe operation
of the vehicle.
WARNING:Don't use a cellular phone when you are
driving, you must stop at a safe place to use
a cellular phone.
SSAR014A
o Station Swapping - As an FM signal weak-
ens, another more powerfanul signal near
the same frequency may begin to play. This
is because your radio is designed to lock
onto the clearest signal. If this occurs, select
another station with a stronger signal.
o Multi-Path Cancellation - Radio signals be-
ing received from several directions can cause
distortion or fluttering. This can be caused by
a direct and a reflected signal from the same
station, or by signals from two stations with
close frequencies. If this occurs, select an-
other station until the condition has passed.
SSAR013A
o Fading - As your car moves away from the
radio station, the signal will weaken and
sound will begin to fade. When this occurs,
we suggest that you select another stronger
station.
o Flutter/Static - Weak FM signals or large
obstructions between the transmitter and
your radio can disturb the signal causing
static or fluttering noises to occur. Reducing
the treble level may lessen this effect until
the disturbance clears.

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 69
FAD (Fader Control) KnobPull the treble control knob further out.
Turn the control knob counterclockwise to em-
phasize front speaker sound. (Rear speaker
sound will be attenuated)
When the control knob is turned clockwise, rear
speaker sound will be emphasized.
(Front speaker sound will be attenuated)
4. TUNE (Manual) Select ButtonPress the side or side to increase or to
decrease the frequency. Press either button
and hold down to continuously scroll. Release
button once the desired station is reached.
SEEK Operation (Automatic Channel
Selection)
Press the TUNE select button 0.5 sec or more.
Releasing it will automatically tune to the next
available station with a beep sound.
When the side is pressed longer than 0.5
second, releasing will automatically tune to the
next higher frequency and when the side is
pressed longer than 0.5 second, releasing will
automatically tune to the next lower frequency.
5. BAND SelectorPressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis-
played on LCD.
6. PRESET STATION SELECT ButtonSix (6) stations for AM, FM and FM2 respective-
ly can be preset in the electronic memory circuit
on this unit.
HOW TO PRESET STATIONSSix AM and twelve FM stations may be pro-
grammed into the memory of the radio. Then,
by simply pressing the band select button and/
or one of the six station select buttons, you may
recall any of these stations instantly. To pro-
gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM, or FM2.
o Select the desired station to be stored by
seek or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than
two seconds. A select button indicator will
show in the display indicating which select
button you have depressed. The frequency
display will flash after it has been stored into
the memory with a beep sound. You should
then release the button, and proceed to
program the next desired station. A total of
18 stations can be programmed by select-
ing one AM and two FM stations per button.
o When completed, any preset station may be
recalled by selecting AM, FM or FM2 band
and the appropriate station button.
H240B03O-AAT1. POWER ON-OFF Control KnobThe radio unit may be operated when the
ignition key is in the "ACC" or "ON" position.
Press the knob to switch the power on. The
LCD shows the radio frequency in the radio
mode or the tape direction indicator in the tape
mode. To switch the power off, press the knob
again.
VOLUME ControlRotate the knob clockwise to increase the
volume and turn the knob counterclockwise to
reduce the volume.
2. BASS Control KnobPress to pop the knob out and turn to the left or
right for the desired bass tone.
BAL (Balance Control) KnobPull the bass control knob further out. Turn the
control knob clockwise to emphasize right
speaker sound. (Left speaker sound will be
attenuated)
When the control knob is turned counterclock-
wise, left speaker sound will be emphasized.
(Right speaker sound will be attenuated)
3. TREB (Treble Control) KnobPress to pop the knob out and turn to the left or
right for the desired treble tone.
FM/AM

FEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAIFEATURES OF YOUR HYUNDAI FEATURES OF YOUR HYUNDAI
FEATURES OF YOUR HYUNDAI
1- 74
3. BASS Control KnobPress to pop the knob out and turn to the left or
right for the desired bass tone.
TREB (Treble Control) KnobPull the bass control knob further out. Turn to
the left or right for the desired treble tone.
4. SCAN ButtonWhen the scan button is pressed, the fre-
quency will increase and the receivable sta-
tions will be tuned in one after another, receiv-
ing each station for 5 seconds. To stop scan-
ning, press the scan button again.
5. TUNE (Manual) Select ButtonPress the ( ) side or ( ) side to increase or to
decrease the frequency. Press either button
and hold down to continuously scroll. Release
button once the desired station is reached.
SEEK Operation (Automatic Channel
Selection)
Press the TUNE select button for 0.5 sec or
more. Releasing it will automatically tune to the
next available station with a beep sound.
When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the
next higher frequency and when the ( ) side is
pressed longer than 0.5 second, releasing will
automatically tune to the next lower frequency.
6. BAND SelectorPressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis-
played on LCD.
7. PRESET STATION SELECT ButtonSix (6) stations for AM, FM or FM2 respectively
can be preset in the electronic memory circuit
on this unit.
HOW TO PRESET STATIONSSix AM and twelve FM stations may be pro-
grammed into the memory of the radio. Then,
by simply pressing the band select button and/
or one of the six station select buttons, you may
recall any of these stations instantly. To pro-
gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM or FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than
two seconds. A select button indicator will
show in the display indicating which select
button you have depressed. The frequency
display will flash after it has been stored into
the memory.
H260B02E-AAT1. POWER ON-OFF Control KnobThe radio unit may be operated when the
ignition key is in the "ACC" or "ON" position.
Press the knob to switch the power on. The
LCD shows the radio frequency in the radio
mode or the CD track indicator in either the CD
mode or CD AUTO CHANGER mode. To switch
the power off, press the knob again.
VOLUME ControlRotate the knob clockwise to increase the
volume and turn the knob counterclockwise to
reduce the volume.
BALANCE ControlPull and turn the control knob clockwise to
emphasize right speaker sound (Left speaker
sound will be attenuated). When the control
knob is turned counterclockwise, left speaker
sound will be emphasized. (Right speaker sound
will be attenuated)
2. FAD (Fader Control) KnobTurn the control knob counterclockwise to em-
phasize front speaker sound. (Rear speaker
sound will be attenuated) When the control
knob is turned clockwise, rear speaker sound
will be emphasized. (Front speaker sound will
be attenuated)
FM/AM