2003 Hyundai Elantra radiator

DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
6-6
Ambient
temperature
°C ( °F)
G050C01A-AAT
To Check the Coolant Level To Check the Coolant LevelTo Check the Coolant Level To Check the Coolant Level
To Check the Coolant Level
The coolant level can be seen on the side of the
plastic coolant reservoir. The level of the cool-
ant should be between the "LOW" and "FULL"
lines on the reservoir when the engine is cold.
If the level is below the "LOW" mark, add
engine coolant to bring it up between "LOW"
and "FULL". If the level is low, inspect for
coolant leaks and recheck the fluid level fre-quently. If the level drops again, visit your
Hyundai dealer for an inspection and diagnosis
of the reason.
G050D02A-AAT
To Change the Engine Coolant To Change the Engine CoolantTo Change the Engine Coolant To Change the Engine Coolant
To Change the Engine CoolantThe engine coolant should be changed at those
intervals specified in the vehicle maintenance
schedule in Section 5.
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:Engine coolant can damage the finish of Engine coolant can damage the finish ofEngine coolant can damage the finish of Engine coolant can damage the finish of
Engine coolant can damage the finish of
your car. If you spill engine coolant on the your car. If you spill engine coolant on theyour car. If you spill engine coolant on the your car. If you spill engine coolant on the
your car. If you spill engine coolant on the
car, wash it off thoroughly with clean water. car, wash it off thoroughly with clean water.car, wash it off thoroughly with clean water. car, wash it off thoroughly with clean water.
car, wash it off thoroughly with clean water.
1. Park the car on level ground, set the park-
ing brake and remove the radiator cap when
cool.
2. Be sure your drain receptacle is in place.
Open the drain cock on the radiator. Allow
all the engine coolant to drain from the
cooling system, then securely close the drain
cock.
3. Check Section 9 for the capacity of the
cooling system in your car. Then, following
the manufacturer's directions on the engine
coolant container, add the appropriate quan-
tity of coolant to the radiator.
G050D01E
Engine Coolant concentration
Antifreeze
solutionWater
35%
40%
50%
60% -15 (5)
-25 (-13)
-35 (-31)
-45 (-49)65%
60%
50%
40%
4. Turn the radiator cap counterclockwise with-
out pressing down on it, until it stops. This
relieves any pressure remaining in the cool-
ing system. And remove the radiator cap by
pushing down and turning counterclockwise.
Now fill the radiator with clean demineral-
ized or distilled water. Continue to add clean
demineralized or distilled water in small quan-
tities until the fluid level stays up in the
radiator neck.
G050D03E

DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
6-7
CHAMPION
NGKRC10PYP4
PFR5N-11
IFR5G-11 Your engine was originally equipped with plati-
num or iridium-tipped spark plugs.
Platinum or iridium-tipped spark plugs will last
longer than conventional type spark plugs and
can be identified by blue lines (platinum only)
on the ceramic shell.NOTE: NOTE:NOTE: NOTE:
NOTE:Do not clean or regap platinum or iridium- Do not clean or regap platinum or iridium-Do not clean or regap platinum or iridium- Do not clean or regap platinum or iridium-
Do not clean or regap platinum or iridium-
tipped spark plugs. tipped spark plugs.tipped spark plugs. tipped spark plugs.
tipped spark plugs.
G050D04E
5. Start the engine, top off the radiator with
water and then add engine coolant to the
reservoir until the level is between "LOW"
and "FULL".
6. Replace the radiator and reservoir caps and
check to be sure the drain cocks are fully
closed and not leaking.
WARNING: WARNING:WARNING: WARNING:
WARNING:The cooling fan is controlled by engine cool- The cooling fan is controlled by engine cool-The cooling fan is controlled by engine cool- The cooling fan is controlled by engine cool-
The cooling fan is controlled by engine cool-
ant temperature and may sometimes oper- ant temperature and may sometimes oper-ant temperature and may sometimes oper- ant temperature and may sometimes oper-
ant temperature and may sometimes oper-
ate even when the engine is not running. ate even when the engine is not running.ate even when the engine is not running. ate even when the engine is not running.
ate even when the engine is not running.
Use extreme caution when working near the Use extreme caution when working near theUse extreme caution when working near the Use extreme caution when working near the
Use extreme caution when working near the
blades of the cooling fan so that you are not blades of the cooling fan so that you are notblades of the cooling fan so that you are not blades of the cooling fan so that you are not
blades of the cooling fan so that you are not
injured by a rotating fan blade. As the en- injured by a rotating fan blade. As the en-injured by a rotating fan blade. As the en- injured by a rotating fan blade. As the en-
injured by a rotating fan blade. As the en-
gine coolant temperature decreases, the fan gine coolant temperature decreases, the fangine coolant temperature decreases, the fan gine coolant temperature decreases, the fan
gine coolant temperature decreases, the fan
will automatically shut off. This is a normal will automatically shut off. This is a normalwill automatically shut off. This is a normal will automatically shut off. This is a normal
will automatically shut off. This is a normal
condition. condition.condition. condition.
condition.
SSA6060A
0.039 ~ 0.043 in. (1.0 ~ 1.1 mm)
G060A03Y-AAT
SPARK PLUGS SPARK PLUGSSPARK PLUGS SPARK PLUGS
SPARK PLUGS
PLATINUM
PLATINUM
IRIDIUM*
G060B02E-AAT
Replacing the Spark Plugs Replacing the Spark PlugsReplacing the Spark Plugs Replacing the Spark Plugs
Replacing the Spark PlugsThe spark plugs should be changed at the
intervals specified in the vehicle maintenance
schedule in Section 5 or whenever engine per-
formance indicates they should be changed.
Symptoms that suggest poor spark plug perfor-
mance include engine misfiring under load, loss
of fuel economy, poor acceleration, etc. When
spark plugs are replaced, always use spark
plugs recommended by Hyundai. The use of
other spark plugs can result in loss of perfor-
mance, radio interference or engine damage.
NOTE: NOTE:NOTE: NOTE:
NOTE:When replacing the spark plugs, genuine When replacing the spark plugs, genuineWhen replacing the spark plugs, genuine When replacing the spark plugs, genuine
When replacing the spark plugs, genuine
Hyundai replacement parts are recom- Hyundai replacement parts are recom-Hyundai replacement parts are recom- Hyundai replacement parts are recom-
Hyundai replacement parts are recom-
mended. mended.mended. mended.
mended.
Recommended Spark Plugs: Recommended Spark Plugs:Recommended Spark Plugs: Recommended Spark Plugs:
Recommended Spark Plugs:
* 2.0L SULEV Only.

DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
6-9
G090A01A-AAT
FILLING THE WASHER RESERVOIR FILLING THE WASHER RESERVOIRFILLING THE WASHER RESERVOIR FILLING THE WASHER RESERVOIR
FILLING THE WASHER RESERVOIR
The washer fluid reservoir supplies fluid to the
windshield washer system.
A good quality washer fluid should be used to fill
the washer reservoir. The fluid level should be
checked more frequently during bad weather or
whenever the washer system is in more fre-
quent use.
The capacity of the washer reservoir is 3.2 U.S.
quarts (3.0 Liters).
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:o oo o
o
Radiator anti-freeze (engine coolant) Radiator anti-freeze (engine coolant)Radiator anti-freeze (engine coolant) Radiator anti-freeze (engine coolant)
Radiator anti-freeze (engine coolant)
should not be used in the washer system should not be used in the washer systemshould not be used in the washer system should not be used in the washer system
should not be used in the washer system
because it will damage the car's finish. because it will damage the car's finish.because it will damage the car's finish. because it will damage the car's finish.
because it will damage the car's finish.
o oo o
o
The washer lever should not be pulled The washer lever should not be pulledThe washer lever should not be pulled The washer lever should not be pulled
The washer lever should not be pulled
and the washer should not be operated and the washer should not be operatedand the washer should not be operated and the washer should not be operated
and the washer should not be operated
if the washer reservoir is empty. This can if the washer reservoir is empty. This canif the washer reservoir is empty. This can if the washer reservoir is empty. This can
if the washer reservoir is empty. This can
damage the washer fluid pump. damage the washer fluid pump.damage the washer fluid pump. damage the washer fluid pump.
damage the washer fluid pump.
G090A01E G070A01S-AAT
CHANGING THE AIR CLEANER FILTER CHANGING THE AIR CLEANER FILTERCHANGING THE AIR CLEANER FILTER CHANGING THE AIR CLEANER FILTER
CHANGING THE AIR CLEANER FILTER
To change the filter, unsnap the clips around
the cover. When this is done, the cover can be
lifted off, the old filter removed and the new filter
put in its place. Genuine Hyundai Replacement
Parts are recommended.
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:Operating your vehicle without a proper air Operating your vehicle without a proper airOperating your vehicle without a proper air Operating your vehicle without a proper air
Operating your vehicle without a proper air
filter in place can result in excessive engine filter in place can result in excessive enginefilter in place can result in excessive engine filter in place can result in excessive engine
filter in place can result in excessive engine
wear. wear.wear. wear.
wear.
G080A02A-AAT
WINDSHIELD WIPER BLADES WINDSHIELD WIPER BLADESWINDSHIELD WIPER BLADES WINDSHIELD WIPER BLADES
WINDSHIELD WIPER BLADES
The wiper blades should be carefully inspected
from time to time and cleaned to remove accu-
mulations of road film or other debris. To clean
the wiper blades and arms, use a clean sponge
or cloth with a mild soap or detergent and water.
If the wipers continue to streak or smear the
glass, replace them with Genuine Hyundai
Replacement Parts or their equivalent.
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:o oo o
o
Do not operate the wipers on dry glass. Do not operate the wipers on dry glass.Do not operate the wipers on dry glass. Do not operate the wipers on dry glass.
Do not operate the wipers on dry glass.
This can result in more rapid wear of the This can result in more rapid wear of theThis can result in more rapid wear of the This can result in more rapid wear of the
This can result in more rapid wear of the
wiper blades and may scratch the glass. wiper blades and may scratch the glass.wiper blades and may scratch the glass. wiper blades and may scratch the glass.
wiper blades and may scratch the glass.
o oo o
o
Keep the blade rubber out of contact Keep the blade rubber out of contactKeep the blade rubber out of contact Keep the blade rubber out of contact
Keep the blade rubber out of contact
with petroleum products such as engine with petroleum products such as enginewith petroleum products such as engine with petroleum products such as engine
with petroleum products such as engine
oil, gasoline, etc. oil, gasoline, etc.oil, gasoline, etc. oil, gasoline, etc.
oil, gasoline, etc.
G070A01EG080A01E

DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
6-13
G150A01A-AAT
CHECKING STEERING WHEEL CHECKING STEERING WHEELCHECKING STEERING WHEEL CHECKING STEERING WHEEL
CHECKING STEERING WHEEL
FREE-PLAY FREE-PLAYFREE-PLAY FREE-PLAY
FREE-PLAY
To check the steering wheel free-play, stop the
car with the wheels pointed straight ahead and
gently move the steering wheel back and forth.
Use very light finger pressure and be sensitive
to changes in resistance that mark the limits of
the free-play. If the free-play is greater than
specified, have it inspected by your Hyundai
dealer and adjusted or repaired if necessary.1.18in
(30 mm)
G150A02E
G140B01A-AATChecking the Air Conditioning Checking the Air ConditioningChecking the Air Conditioning Checking the Air Conditioning
Checking the Air Conditioning
Operation OperationOperation Operation
Operation
1. Start the engine and let it run at a fast idle for
several minutes with the air conditioning set
at the maximum cold setting.
2. If the air coming out of the in-dash vents is
not cold, have the air conditioning system
inspected by your Hyundai dealer.
CAUTION: CAUTION:CAUTION: CAUTION:
CAUTION:Running the air conditioning system for Running the air conditioning system forRunning the air conditioning system for Running the air conditioning system for
Running the air conditioning system for
extended periods of time with a low refriger- extended periods of time with a low refriger-extended periods of time with a low refriger- extended periods of time with a low refriger-
extended periods of time with a low refriger-
ant level may damage the compressor. ant level may damage the compressor.ant level may damage the compressor. ant level may damage the compressor.
ant level may damage the compressor.
G140C01A-AAT
Lubrication LubricationLubrication Lubrication
LubricationTo lubricate the compressor and the seals in
the system, the air conditioning should be run
for at least 10 minutes each week. This is
particularly important during cool weather when
the air conditioning system is not otherwise in
use.
G140A01A-AAT
AIR CONDITIONING CARE AIR CONDITIONING CAREAIR CONDITIONING CARE AIR CONDITIONING CARE
AIR CONDITIONING CARE
Keeping the Condenser Clean Keeping the Condenser CleanKeeping the Condenser Clean Keeping the Condenser Clean
Keeping the Condenser Clean
The air conditioning condenser (and engine
radiator) should be checked periodically for
accumulation of dirt, dead insects, leaves, etc.
These can interfere with maximum cooling effi-
ciency. When removing such accumulations,
brush or hose them away carefully to avoid
bending the cooling fans.
G140D01A-AAT
Checking the Compressor Drive Belt Checking the Compressor Drive BeltChecking the Compressor Drive Belt Checking the Compressor Drive Belt
Checking the Compressor Drive Belt
When the air conditioning is being used regular-
ly, the compressor drive belt tension should be
checked at least once a month with the engine
turned off.
To check the drive belt tension, press down on
the belt halfway between the engine crankshaft
and compressor pulleys. Pressing with your
finger, you should not be able to deflect this belt
anymore than 1/3 of an inch. If you have the
instruments to check it, with a force of 22 lb.
(98N), the deflection should be 0.315 inches
(approx 8.0 mm). If the belt is too loose, have it
adjusted by your Hyundai dealer.
G140B01A
A/C0.315 in.
(8 mm)
CRANK PULLEY TENSION PULLEY

VEHICLE SPECIFICATIONS VEHICLE SPECIFICATIONSVEHICLE SPECIFICATIONS VEHICLE SPECIFICATIONS
VEHICLE SPECIFICATIONS
9-3 Oil & Grease Standard
HYUNDAI GENUINE PARTS MTF 75W/90 (API GL-4)
HYUNDAI GENUINE ATF, DIAMOND ATF SP-III, SK ATF SP-III
PSF-3
DOT 3, DOT 4 or equivalent
Ethylene glycol base for aluminum radiatorHot Climate: SAE 20W-40, 20W-50 (ABOVE 32°F or 0°C)
Normal Climate :SAE 10W-30, 10W-40, 10W-50 (ABOVE -10°F or -23°C)
Cold Climate: SAE 5W-30, 5W-40 (BELOW 1 0 0 °F or 3 8 °C)
SAE 10W-30, 10W-40, (ABOVE -10°F or -23°C)
SAE 5W-30, 5W-40 (BELOW 95°F or 38°C)
J080A05E-AAT
LUBRICATION CHART LUBRICATION CHARTLUBRICATION CHART LUBRICATION CHART
LUBRICATION CHART
Item
Engine Oil
Transaxle
Power Steering
Brake Fluid
Coolant
API SG
OR SG/CD
API SH
OR
ILSAC GF-I
AND ABOVE2.0 L
2.0 L
SULEV
Manual
Auto
Q'ty
Drain and refill
Without oil filter 3.75 US.QTS (3.12 lmp.qts, 3.55 liter)
With oil filter 4.07 US.QTS (3.39 lmp.qts, 3.85 liter)
2.3 US. QTS. (1.86 Imp. qts., 2.15 liter)
8.2 US. QTS. (6.8 Imp.qts., 7.8 liter)
0.95 US. QTS. (0.79 Imp.qts., 0.9 liter)
As required
6.4 US.QTS (5.31 Imp.qts., 6.0 liter)