2003 Hyundai Coupe tow

CONTROLS AND EQUIPMENT1- 15
B230G01A-GAT Installation on the Outboard Rear Seats
B230G01GK
On outboard rear seats
To install a child restraint system in the outboard rear seats, extend the shoulder/lap belt from itsretractor. Install the child restraint system, bucklethe seat belt and allow the seat belt to take up anyslack. Make sure that the lap portion of the belt istight around the child restraint system and theshoulder portion of the belt is positioned so thatit cannot interfere with the child's head or neck.After installation of the child restraint system, tryto move it in all directions to be sure the childrestraint system is securely installed.If you need to tighten the belt, pull more webbingtoward the retractor. When you unbuckle theseat belt and allow it to retract, the retractor willautomatically revert back to its normal seatedpassenger emergency locking usage condition. NOTE:
o Before installing the child restraint sys-
tem, read the instructions supplied by thechild restraint system manufacturer.
o If the seat belt does not operate as de- scribed, have the system checked imme-diately by your authorized Hyundai dealer.
WARNING:Do not install any child restraint system in thefront passenger seat. Should an accidentoccur and cause the passenger side airbagto deploy, it could severely injure or kill aninfant or child seated in an infant or childseat. Therefore, only use a child restraintsystem in the rear seat of your vehicle. B230B02GK-GAT Using a Child Restraint System with "Tether Anchorage" System For small children and babies, the use of a child seat or infant seat is required. This child seat orinfant seat should be of appropriate size for thechild and should be installed in accordance withthe manufacturer's instructions. It is further re-quired that the seat be placed in the vehicle's rearseat since this can make an important contribu-tion to safety. Your vehicle is provided with twochild restraint hook holders for installing the childseat or infant seat.
B230B01Y
Cover, Child Restraint Hook Holder
Bolt, Holder (5/16"-30 mm)
Washer, Conical Spring Holder, Child Restraint HookSpacer, Hook Holder Cover Spacer (10 mm), Child Restraint Hook HolderRetainer Washer

CONTROLS AND EQUIPMENT
1- 24
o If components of the airbag system must
be discarded, or if the vehicle must be scrapped, certain safety precautions mustbe observed. Your Hyundai dealer knowsthese precautions and can give you thenecessary information. Failure to followthese precautions and procedures couldincrease the risk of personal injury.
o If you sell your vehicle, be sure to inform the new owner of these important pointsand make certain that this manual istransferred to the new owner togetherwith the vehicle.
o If your car was flooded and has soaked carpeting or water on flooring, youshouldn't try to start engine; have cartowed to authorized Hyundai dealer.

CONTROLS AND EQUIPMENT
1- 28 SB2100I-E
DOOR AJAR WARNING LAMP
The door ajar warning lamp indicates that a door is not correctly closed. Ensure that the lamp isextinguished prior to driving the vehicle.
SB210P1-E
LOW FUEL LEVEL WARNING LAMP
The low fuel warning lamp serves to warn the driver that the remaining fuel quantity is approxi-mately 9 litres and that the vehicle should berefuelled. If the vehicle is driven for an extendedperiod with the low fuel warning lamp illuminatedthere exists a possibility that misfiring due to fuel
becoming defective, approximately fifty per centof the normal braking performance will be avail-able.If failure of one of the circuits occurs, the requiredamount of pedal effort, pedal travel and stoppingdistance will be increased. Use of the gearbox isrecommended to assist in bringing the vehicle torest. The vehicle must not be driven once brakefailure has occurred until the system has beenrepaired and is functioning normally.The braking system employs a vacuum servo inorder that the pedal efforts are reduced. Powerfor the servo is derived from the engine andtherefore, in the event of the engine stopping orthe vehicle being towed, pedal efforts will besubstantially increased. SB210M1-E
CHARGING SYSTEM WARNING LAMP
The charging system warning lamp should illumi- nate when the ignition switch is turned to the"ON" position and should be extinguished whenthe engine is started. If the lamp fails to illuminatewhen the ignition is turned "ON" or fails to extin-guish after starting the engine, the nearestHyundai dealer should be contacted. If the lampilluminates whilst the vehicle is being driven, stopthe vehicle as soon as it is safe to do so andcheck the condition of the generator drive belt. Ifthe belt is in place and the tension is satisfactory,the advice of a Hyundai dealer should be sought.
B260H01GK-EAT PARKING BRAKE/BRAKE FLUID LEVEL WARNING LAMP
CAUTION: In the event of problems being suspected with the braking system, the advice of thenearest Hyundai dealer must be sought be-fore the vehicle is driven. Driving the vehiclewith either an electrical or hydraulic brakingsystem defect may be dangerous, resultingin accident or personal injury. Warning lamp operation The parking brake/brake fluid level warning lamp will be illuminated whenever the ignition switch isturned to the "ON" or "START" position when theparking brake is applied and must be extin-guished in a three seconds after the enginestarts.If the warning lamp fails to extinguish or illumi-nates at any other time, the vehicle must bebrought to rest in a safe location and the level ofbrake fluid in the reservoir checked. If the fluidlevel is incorrect, fluid conforming to DOT 3 orDOT 4 specifications should be added. If, aftercorrecting the brake fluid level, the warning lampcontinues to be illuminated, the advice of thenearest Hyundai dealer must be sought beforethe vehicle is driven again.The Hyundai Coupe is equipped with a diago-nally split dual braking system which will ensurethat in the event of one of the brake circuits SB210N2-E
HATCHBACK DOOR OPEN WARNING LAMP
The hatchback door warning lamp indicates when the hatchback door is open or is not fully closed.Ensure that the lamp has extinguished prior todriving the vehicle.CAUTION: If the drive belt (generator belt) is loose,broken, or missing while the vehicle is driv-ing, there may be a serious malfunction, en-gine could overheat because this belt alsodrives the water pump.

CONTROLS AND EQUIPMENT
1- 34 SB220D1-E HIGH AND LOW BEAM To turn on the headlight high beams, push the lever forward (away from you). For low beams,pull the lever back (toward you). The appropriateheadlight beam indicator light will come on at thesame time.
SB220E1-E HEADLIGHT FLASH
SB220C3-ELIGHTING SWITCH The vehicle sidelamps and headlamps are oper- ated by rotating the end of the turn signal switchbarrel. To operate the sidelight, rotating the switchto the first detent with ignition switch at the "OFF"position will cause the lamps to illuminate. Tooperate the headlamps, the turn signal switchbarrel should be rotated to the second detent.The headlamps will only operate when the igni-tion switch is at the "On" position. If the ignitionswitch is turned to the "Off" position, only thesidelight will function. The headlight may be flashed by pulling the turnsignal switch lever towards the steering wheel.The headlight will be extinguished when theswitch is released.
To indicate an intention to change lanes, movingthe lever slightly towards the direction of therelevant turn signal will cause the turn signallamps to flash. When the lever is released, it willreturn to the "off" position.
HGK039-D
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. Ifyou set the multi-function switch to "AUTO", thetail lights and headlights will be turned automati-cally on or off according to external illumination.
B340G01L-GAT Auto Light (Not all models)
HGK041-D
HGK233-D
NOTE: The ignition must be in the "ON" position toturn on the headlights. Parking light auto cut If you do not turn the parking lights "OFF" afterdriving, the parking lights will automatically shut"OFF" when the driver's door is opened.To turn them "ON" again you must simply turn theignition key to the "ON" position.

CONTROLS AND EQUIPMENT1- 35
SB230B1-E VARIABLE INTERMITTENT WIPE FACILITY (Not all models)
B350A01GK-EAT WINDSCREEN WIPER/WASHER SWITCH The windscreen wiper switch, dependent upon model, has three operating positions.1. Intermittent wiper operation. (Not all models)2. Low speed operation.3. High speed operation. NOTE: To prevent damage to the wiper system, donot attempt to wipe away heavy accumula-tions of snow or ice.Accumulated snow and ice should be re-moved manually. If there is only a light layerof snow or ice, operate the heater in thedefrost mode to melt the snow or ice beforeusing the wiper. The variable intermittent wipe facility is operatedby moving the windscreen wiper switch to thefirst position. The time period between wipes isadjusted by moving the rotary control on thewindscreen wiper switch barrel. B350B01O-EAT WINDSCREEN WASHER OPERATION To use the windscreen washer, pull the wiper/ washer lever toward the steering wheel. Whenthe washers are operated, the wipers automati-cally make two passes across the windscreen.The washers continue to operate until the lever isheld at the washer position. NOTE:
o Do not operate the washers for more than
15 seconds continuously or when the flu-id reservoir is empty.
HGK042-D
(1)
(2) (3)
HGK043-D
Mist Wiper Operation
HGK045-D
If a single wipe is desired in mist, move the windscreen wiper and washer control lever up.
HGK044-D

CONTROLS AND EQUIPMENT
1- 42 CAUTION:
o Do not operate the switch continuously
for an unnecessary length of time.
o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approvedde-icer.
WARNING:Be careful when judging the size or distanceof any object seen in the passenger siderear view mirror. It is a convex mirror with acurved surface. Any objects seen in thismirror are closer than they appear. SB360C1-F FOLDING THE OUTSIDE REAR VIEW MIRRORS To fold the outside rear view mirrors, push them towards the rear.The outside rear view mirrors can be foldedrearward for parking in restricted areas. WARNING: Do not adjust or fold the outside rear viewmirrors while the vehicle is moving. Thiscould result in loss of control, and an acci-dent causing death, serious injury or proper-ty damage.
B510D01Y-EAT OUTSIDE REARVIEW MIRROR HEATER (Not all models) The outside rearview mirror heater is actuated in connection with the rear window defroster. Toheat the outside rearview mirror glass, push in the switch for the rear window defroster. Therearview mirror glass will be heated for defrost-ing or defogging and will give you improved rearvision in inclement weather conditions. Push theswitch again to turn the heater off. The outsiderearview mirror heater automatically turns itselfoff after 15 minutes.
B510C01GK
B380A01GK
A Type
B Type
HGK128-D
YB270B2-A EXTERIOR REAR VIEW MIRROR Electric Type The outside rear view mirror can be adjusted in any direction to give the maximum rear viewvision. The remote control out side rear view mirror switch controls the adjustments for both rightand left door mirror. To adjust the position of either mir- ror:
1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.
2. Now, adjust mirror angle by depressing the appropriate perimeter switch as illustrated.

CONTROLS AND EQUIPMENT1- 43
SB380A1-E PARKING BRAKE The parking brake must always be set when the vehicle is to be left unattended. When the parking brake is applied, and the ignition key is at the "ON" position, the parking brake warning lampwill be illuminated. Before driving the vehicle, theparking brake must be fully released and thewarning lamp extinguished.
o To set the parking brake, apply the foot brake
and pull the parking brake lever up with the button depressed. Release the button whenthe brake is fully applied.
o To release the parking brake, apply the foot brake and pull up the parking brake leverslightly. Depress the button and lower thelever.
SB370A1-E INTERIOR REAR VIEW MIRROR The interior mirror is of the day/night type to enable the glare of headlamps from followingvehicles to be eliminated during night time driv-ing.The tab located at the bottom of the mirror shouldbe set to the position nearest the windscreen fornormal day time driving, and flipped towards therear of the vehicle to eliminate glare during nighttime driving. To adjust the field of vision, themirror may be moved by hand upon the mount-ing. NOTE: The mirror should always be adjusted prior tosetting the vehicle in motion.
B520A01GK
B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (Not all models) The electric type day/night inside rearview mirror automatically controls the glare of headlights ofthe car behind you. Adjust the rearview mirror tothe desired position.
B520B01GK
Sensor
HGK178

CONTROLS AND EQUIPMENT1- 47
SB450C2-E To Unlock Using the Key To open the hatchback door using the ignition key, insert the key into the lock barrel and turnclockwise to release the latch. The hatchbackdoor compartment lamp will illuminate wheneverthe hatchback door is opened.
B540C01GK
B540D01GK-GAT When you close the hatchback door
HGK226
HGK227
WARNING:
Do not close an open hatchback door while a person(s) is sitting upright on the rear seat.The hatchback door or hatchback door glassmay contact the head of a person sittingupright on the rear seat. Closing the hatch-back door onto a person's head may causeserious injuries, including death.
SB510A1-E SUNVISOR Sun visors are fitted to both the driver and pas- senger side of the vehicle. Certain derivativesare equipped with a vanity mirror which is locatedon the back of the passenger visor. The visormay be lowered to reduce the amount of glarefrom directly ahead, or may be moved towardsthe side window to reduce glare from the side ofthe vehicle, once the inner pivot has beenunclipped from the bracket. WARNING: Do not place the sunvisor in such a mannerthat it obscures visibility of the roadway,traffic or the objects. Vanity mirror
HGK145-D