2003 Hyundai Coupe Lights

CONTROLS AND EQUIPMENT
1- 34 SB220D1-E HIGH AND LOW BEAM To turn on the headlight high beams, push the lever forward (away from you). For low beams,pull the lever back (toward you). The appropriateheadlight beam indicator light will come on at thesame time.
SB220E1-E HEADLIGHT FLASH
SB220C3-ELIGHTING SWITCH The vehicle sidelamps and headlamps are oper- ated by rotating the end of the turn signal switchbarrel. To operate the sidelight, rotating the switchto the first detent with ignition switch at the "OFF"position will cause the lamps to illuminate. Tooperate the headlamps, the turn signal switchbarrel should be rotated to the second detent.The headlamps will only operate when the igni-tion switch is at the "On" position. If the ignitionswitch is turned to the "Off" position, only thesidelight will function. The headlight may be flashed by pulling the turnsignal switch lever towards the steering wheel.The headlight will be extinguished when theswitch is released.
To indicate an intention to change lanes, movingthe lever slightly towards the direction of therelevant turn signal will cause the turn signallamps to flash. When the lever is released, it willreturn to the "off" position.
HGK039-D
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. Ifyou set the multi-function switch to "AUTO", thetail lights and headlights will be turned automati-cally on or off according to external illumination.
B340G01L-GAT Auto Light (Not all models)
HGK041-D
HGK233-D
NOTE: The ignition must be in the "ON" position toturn on the headlights. Parking light auto cut If you do not turn the parking lights "OFF" afterdriving, the parking lights will automatically shut"OFF" when the driver's door is opened.To turn them "ON" again you must simply turn theignition key to the "ON" position.

CONTROLS AND EQUIPMENT
1- 38
SB320A2-F HEADLIGHT LEVELING DEVICE SYS- TEM
HGK157-D
To adjust the headlight beam level according to the number of the passengers and the loadingweight in the luggage area, turn the beam level-ing switch.The higher the number of the switch position, thelower the headlight beam level.Always keep the headlight beam at the properleveling position, or headlights may dazzle otherroad users.Listed below are the examples of recommendedswitch settings.For loading conditions other than those listedbelow, adjust the switch position so that thebeam level may be the nearest as the conditionobtained according to the list.
B450A01GK-GAT DRINK HOLDER (Not all models)
HGK149-D
The drink holder is used for holding cups or cans. To use the passenger's drink holder, push thedrink holder. WARNING: Do not place objects other than cups or cansin the drink holder. Such objects can bethrown out in the event of a sudden stop or anaccident, possibly injuring the passengers inthe vehicle. Driver's
Passenger's
B430A01GK-AAT FRONT ASHTRAY The front ashtray may be opened by pushing and releasing the ashtray door at its top edge. To remove the ashtray in order to clean it, the metal ash receptacle should be lifted out from theashtray door. Do not attempt to remove the entireashtray door assembly or damage will result. Toreinstall it, place it in the proper position andpress it down in the ashtray door. The ashtraylamp will only illuminate when the exterior bodylights are switched on.HGK146-D

CONTROLS AND EQUIPMENT1- 43
SB380A1-E PARKING BRAKE The parking brake must always be set when the vehicle is to be left unattended. When the parking brake is applied, and the ignition key is at the "ON" position, the parking brake warning lampwill be illuminated. Before driving the vehicle, theparking brake must be fully released and thewarning lamp extinguished.
o To set the parking brake, apply the foot brake
and pull the parking brake lever up with the button depressed. Release the button whenthe brake is fully applied.
o To release the parking brake, apply the foot brake and pull up the parking brake leverslightly. Depress the button and lower thelever.
SB370A1-E INTERIOR REAR VIEW MIRROR The interior mirror is of the day/night type to enable the glare of headlamps from followingvehicles to be eliminated during night time driv-ing.The tab located at the bottom of the mirror shouldbe set to the position nearest the windscreen fornormal day time driving, and flipped towards therear of the vehicle to eliminate glare during nighttime driving. To adjust the field of vision, themirror may be moved by hand upon the mount-ing. NOTE: The mirror should always be adjusted prior tosetting the vehicle in motion.
B520A01GK
B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (Not all models) The electric type day/night inside rearview mirror automatically controls the glare of headlights ofthe car behind you. Adjust the rearview mirror tothe desired position.
B520B01GK
Sensor
HGK178

CONTROLS AND EQUIPMENT
1- 44
B550A02S-DAT HIGH-MOUNTED REAR STOPLIGHT
In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rearstoplight in the centre of the rear window orinserted in the rear spoiler also comes on whenthe brakes are applied.
B360B01GK-GAT REAR FOG LIGHT SWITCH (Not all models)
HGK183
To turn on the rear fog lights, push the switch. They will come on when the headlights areturned on.
B550A01GK
A Type B Type
YB800A2-A FRONT FOG LIGHT SWITCH (Not all models) To turn on the front fog lights, push the switch. They will come on when the headlights are turnedon.
HGK142
C Type

CONTROLS AND EQUIPMENT
1- 56
B740A01S-AAT AIR CONDITIONING SYSTEM (Not all models)Air Conditioning Switch
HGK018
The air conditioning is turned on or off by pushing the A/C button on the heating/air conditioningcontrol panel.
HGK002
B740B01S-AAT Air Conditioning Operation Cooling To use the air conditioning to cool the interior:
o Set the side vent control to "OFF", to shut off outside air entry.
o Turn on the fan control switch.
o Turn on the air conditioning switch by pushing in on the switch. The air conditioning indicator lightshould come on at the same time.
o Set the air intake control to "Fresh" mode ( ).
o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The temperaturemay be moderated by moving the controltoward "Warm".)
o Adjust the fan control to the desired speed. For greater cooling, turn the fan control toone of the higher speeds or temporarilyselect the "Recirculation" position on the airintake control.B740C01S-AAT Dehumidified HeatingFor dehumidified heating:
o Turn on the fan control switch.
o Turn on the air conditioning switch. The airconditioning indicator light should come on atthe same time.
o Set the air intake control to "Fresh" mode ( ).
o Set the air flow control to "Face".
o Adjust the fan control to the desired speed.
o For more rapid action, set the fan at one of the higher speeds.
o Adjust the temperature control to provide the desired amount of warmth.

DRIVING YOUR HYUNDAI
2- 2 SC030A1-E
BEFORE STARTING THE ENGINE
Before you start the engine, you should always:
1. Look around the vehicle to be sure there are no flat tires, puddles of oil or water or other indications of possible trouble.
2. After entering the car, check to be sure the parking brake is engaged.
3. Check that all windows, and lights are clean.
4. Check that the interior and exterior mirrors are clean and in position.
5. Check your seat, seatback and head re- straint to be sure they are in their properpositions.
6. Close all the doors.
7. Fasten your seat belt and be sure that all other occupants have fastened theirs.
8. Turn off all lights and accessories that are not needed.
9. When you turn the ignition switch to "ON' check that all appropriate warning lights are operating and that you have sufficient fuel.
10.Check the operation of warning lights and all bulbs when key is in the "ON" position. o To start the engine, insert the ignition key
and turn it to the "START" position. Releaseit as soon as the engine starts. Do not holdthe key in the "START" position for more that15 seconds.
NOTE: For safety, the engine will not start if the shift lever is not in "P" or "N" Position (AutoT/A).
SC040A1-F
COMBINATION IGNITION SWITCH AND STEERING LOCK To Start the Engine
o If your Hyundai is equipped with a manual
transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic transaxle, place the shift lever in "P" (park). SC050A2-E
KEY POSITIONS WARNING:
The engine must never be turned off and the key removed from the ignition key cylinderwhilst the vehicle is in motion since thesteering lock will operate and control of thevehicle will be lost. "START"
The engine is started in this position. It willcrank until you release the key. NOTE: Do not hold the key in the "START" position for more than 15 seconds.
"ON" When the key is at the "ON" position, the ignition and all accessories are available for use. If theengine is not running, the key should not be leftat this position since the battery will becomedischarged and damage to the ignition systemmay also result. For information regarding en-gine starting, refer to "STARTING THE EN-GINE". "ACC" When the ignition key is at the "ACC" position, the radio and other accessories may be used. "LOCK" The ignition key may only be inserted or removed at this position.
C040A01E
LOCK
ACC
ON
START

DRIVING YOUR HYUNDAI
2- 6 The first few shifts on a new vehicle, or if the battery has been disconnected, may besomewhat abrupt. This is a normal condi-tion, and the shifting sequence will adjustafter shifts are cycled a few times by theT.C.M (Transaxle Control Module). CAUTION: Never shift into "R" or "P" position while the vehicle is moving. The indicator lights in the instrument cluster indicate the selector lever position when theignition is switched "ON". During "D" or sportsmode operation, the gear currently in use dis-plays in the numeral indicator.
C090A02L-D
C090B01A-AAT
The function of each position is as follows:
o P (Park): Use to hold the vehicle in place when parked or while starting the engine. Whenever parking thecar, apply the parking brake and shift the selec-tor lever to the "P" (Park) position. CAUTION: Never place the selector lever in the "P"(Park) position unless the vehicle is fullystopped. Failure to observe this caution willcause severe damage to the transaxle. C090C01A-AAT
o R(Reverse): Use for backing up the vehicle. Bring the car to a complete stop before shifting the selectorlever to "R" position. C090D02O-AAT
o N (Neutral): In the "N" position, the transaxle is in neutral, which means that no gears are engaged. Theengine can be started with the shift lever in "N"position, although this is not recommended ex-cept if the engine stalls while the car is moving.
HGK174-D
C090A04Y-GAT
AUTOMATIC TRANSAXLE
The highly efficient Hyundai automatic transaxle
has four forwards speeds and one reverse speed. The individual speeds are selected au-tomatically, depending on the position of thespeed selector lever. The selector lever has 2gates; the main gate and the manual gate.
NOTE: For information on manual gate operation,
refer to "Sports Mode".
In the main gate, the selector lever has 4
positions, and is equipped with a button to avoid inadvertent wrong selection.
NOTE: Depress the brake pedal and push the
button when shifting.
Push the button when shifting. The selector lever can be shifted freely.

DRIVING YOUR HYUNDAI
2- 10 C310D01O-AAT
Indicators and Warning The indicators should illuminate when the igni-
tion key is turned to ON or START but should go out after three seconds.
If the indicators do not illuminate, or the TCS or
TCS-OFF indicator does not go out after 3seconds, have it checked by an authorizeddealer.
Should there be any unusual conditions in the
device while driving, TCS-OFF indicator illumi-nates as a warning.
If TCS-OFF indicator illuminates, pull your car
to a safe place and stop the engine. Then, start the engine again to check if the
TCS-OFF indicator goes out.
If the indicator remains lit even after the engine
has been started, have your car checked by anauthorized Hyundai dealer. effect of brake control and indicates noth-ing unusual.
3) When the engine starts, a click is heard from the engine compartment; however,this is only the sound of traction controlbeing checked.
4) When moving out of the mud or fresh snow, pressing the accelerator pedal maynot cause the engine speed to increasedue to TCS operation. NOTE:
1) When the TCS-OFF indicator illuminates,
traction control is automatically deacti- vated for safety.
2) This warning function is not provided when the driver selects the TCS-OFFmode.
SC150A1-F DRIVING FOR ECONOMY You can save fuel and get more miles from your car if you follow these suggestions:
o Drive smoothly. Accelerate at a moderate rate. Don't make "jack-rabbit" starts or full- throttle shifts and maintain a steady cruisingspeed. Don't race between stoplights. Try toadjust your speed to that of the other trafficso you don't have to change speeds unnec-essarily. Avoid heavy traffic whenever possible. Al- ways maintain a safe distance from othervehicles so you can avoid unnecessary brak-ing. This also reduces brake wear.
o Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving ata moderate speed, especially on the high-way, is one of the most effective ways toreduce fuel consumption.
o Don't "ride" the brake or clutch pedal. This can increase fuel consumption and alsoincrease wear on these components. In ad-dition, driving with your foot resting on thebrake pedal may cause the brakes to over-
C310B01O-AAT
TCS ON/OFF Mode When the TCS is running, the TCS indicator
light in the instrument cluster will blink. If you turn the system off by pressing the TCS
switch, the TCS-OFF indicator light will comeon and stay on. In the TCS-OFF mode, theSLIP control will be deactivated. Adjust youdriving accordingly. To turn the system backon, press the switch again. The TCS-OFF indi-cator light should go off.
NOTE:
1) The TCS mode will automatically be turned ON after the engine is turned offand restarted.
2) When the traction control system is op- erating properly, you can feel a slightpulsation in the vehicle. This is only the
CAUTION: When the TCS indicator blinks, SLIP control
has been activated. It also means that the road is slippery or your car is acceleratingexcessively. In this situation, gently releasefoot pressure from the accelerator pedaland maintain moderate speed.
WARNING: Traction control is only a driving aid; all
normal precautions for driving in inclement weather and on slippery road surfacesshould be observed.