2003 Hyundai Coupe ABS

APPEARANCE CARE 4-1
retreatment programme must be observed in accordance with the Terms and Conditionsoutlined in the separate Anti Perforation War-ranty Booklet.
NOTE: The underbody should never be steam
cleaned since the underbody coating may be removed by this process.
During the interim period between power
washing the underbody, the more vulnera-ble areas such as wheel arches should behosed off particularly during the winter sea-son to prevent prolonged contact with roadsalts. Ensure that the various drain points located
at the bottom of the door panels and sillsare kept clear to prevent water from becom-ing trapped within the cavities. Whereverpossible, the parking of the vehicle in aconfined, poorly ventilated location (a ga-rage for example) should be avoided whenthe vehicle is wet or is covered with snow orice. Under these conditions, the internalcavities of the vehicle will remain damp forprolonged periods of time which will en-courage corrosion. Parking the vehicle wheregood ventilation exists (outside for example)is preferable.
SE020A1-E PROTECTING YOUR HYUNDAI FROM CORROSION By using the most advanced design and con- struction practices, every Hyundai is built toretain the original factory finish for many years.However, long term durability is also greatlydependant upon maintaining the various protec-tion systems and coatings used in manufacturesince constant, exposure to the elements willresult in a breakdown and loss of effectiveness.The following suggestions are made to assist inthe maintenance of the vehicle bodywork.
SE030A1-E UNDERBODY COATINGS Every Hyundai passenger car receives a full
underbody and cavity injection treatment during production. In order that this treatment mayretain maximum effectiveness it is recommend-ed that the underbody receives a power washand a thorough inspection after each winterseason. In doing so any accumulations of mud,which act as moisture traps and combine withroad salts to accelerate corrosion will be re-moved. In order to maintain the Anti PerforationWarranty, the requirements regarding the
SE000A1-E
4. APPEARANCE
CARE
E030A01GK-AAT VALETINGRegular cleaning of the exterior paintwork serves two important functions. Firstly, the removal of abrasive dirt and contaminants will maintain thelustre of the paintwork and will preventdiscolouration and dulling due to prolonged con-tact.Secondly, the presence of damage through im-pact or abrasion will be apparent allowing earlyrectification to be made thus preventing corro-sion from becoming established and spreadingbeneath the paint film. To avoid "water spotting"the vehicle should not be washed in direct sun-light particularly in the case of vehicles havingdark body colours. The heat from the sun rays isabsorbed by the paint film increasing the surfacetemperature. This action causes water used forwashing to evaporate quickly leaving behind thedeposits from the water and the shampoo used.Use only a shampoo intended for the purposeand ensure that the body work is thoroughlywetted to soften the dirt film prior to attempting toremove this.After removing the dirt film with a soft sponge, thebody work should be thoroughly rinsed and thendried with a good quality chamois leather toprevent streaking or spotting of the paint work.Household detergents, solvents and abrasivecleaning materials should not be used in order toavoid damaging the paint film.High pressure car washes may cause water toenter your vehicle.Plastic wheel covers should be cleaned using asponge and water. Cast alloy wheels should becleaned using a mild soap or neutral detergent.Abrasive compounds must not be used since inthe event of these damaging the lacquer coating,
4

OWNER MAINTENANCE
6-22
G200C01GK-GAT FUSE PANEL DESCRIPTION Engine Compartment HGK205-EPROTECTED COMPONENTS
GeneratorGeneratorCondenser FanRadiator FanEngine Control, ECM. ATM ControlIgnition, Start Relay ABS ABS Blower InjectorO 2 Sensor, ECM
DRLFront fog LightTCM, ECM Horn. A/conditioner Head Light (High)Head Light (LOW)
FUSE RATING
120A50A 30A30A30A30A 30A 30A30A 15A 10A15A 15A 10A15A 15A 15A
DESCRIPTION
BATT BATT
COND RADECUIGN
ABS 1 ABS 2
BLOWER INJ
SNSR DRL
F/FOG
ECU
HORN,A/CON H/LP (H1)
H/LP (LO)
NOTE:
Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box
on your vehicle, refer to the fuse box label.
Not all models

OWNER MAINTENANCE 6-23
DESCRIPTION
IG COIL
AMP
B/UP LAMP
A/BAG IND A/BAG
HTD MIR
HAZARD
R/WIPER
TAIL-RH
F/WIPER A/C SW
RR DEFOG STOP
TAIL-LH
A/CON ECU
CLUSTER
ROOM LP
P/WINDOW T/GATE IGN
RR FOG
C/LIGHT S/ROOF
S/HTR ABS
AUDIO
G200D01GK-GAT Inner Panel
HGK204-E
PROTECTED COMPONENTS
Ignition Coil, ECM
AMP. Multi Gauge Unit B/Up Lamp Air Bag Indicator Air Bag Outside Mirror Defroster Hazard Warning LightRear Window WiperTaillightFront Window WiperA/ConditionerRear Window Defroster Stop Light Tail lightA/ConditionerECM, Multi Gauge Unit, TCMClusterMap Light, Clock, Audio Power Window Hatchback door OpenA/Con, A.Q.S Sensor Rear Fog C/Lighter, Outside MirrorSunroof Seat Warmer ABS. TCS Audio, Clock
FUSERATING
20A20A 10A 10A 15A10A 10A 15A10A20A10A30A15A 10A 10A10A10A 10A 30A 15A10A 10A 15A15A20A 10A 10A

EMISSION CONTROL SYSTEM 7-1
SH010A1-E EMISSION CONTROL SYSTEMS (Not all models) Depending upon the market for which the vehicleis destined, the emission control system willcomprise one or more of the following emissioncontrol devices. (1) Crankcase emission control system (2) Evaporative emission control system(3) Exhaust emission control system In order that the proper functioning of the emis- sion control systems may be ensured, it isrecommended that the vehicle is inspected andmaintained by an authorized Hyundai dealer inaccordance with the maintenance schedule inthis manual.
SH000A1-E
7. EMISSION
CONTROL SYSTEM
SH010B1-E
1. CRANKCASE EMISSION CONTROL SYSTEM
The positive crankcase ventilation system is employed to prevent air pollution caused byblow-by gases being emitted from the crankcase by introducing fresh air to the crankcase throughthe air cleaner where this mixes with blow-bygases and then passes through the PCV valveinto the intake manifold from where it subse-quently enters the combustion chamber and isburned.
SH010D1-E
3. EXHAUST EMISSION CONTROL SYSTEM The exhaust emission control system is a highlyeffective system which controls exhaust emis-sion while maintaining good vehicle performance.
SH010C1-E
2. EVAPORATIVE EMISSION CONTROL SYSTEM
The Evaporative Emission Control System is designed to prevent fuel vapours from escapinginto the atmosphere through the fuel tank venti-lation system.Whilst the engine is not running, fuel vapours generated inside the fuel tank are absorbed and stored in a charcoal canister. When the engine isstarted, the vapours stored in the canister aredrawn into the induction system through thepurge control solenoid valve and are subse-quently burned.The purge control solenoid valve is controlled bythe ECU; when the engine coolant temperatureis low or the engine is idling, the purge controlvalve is closed and fuel vapours remain stored inthe canister. Under normal running conditionswhen the engine is warm, the valve opens andthe vapours are drawn into the inlet tract andsubsequently burned in the combustion cham-ber. SH020A1-E CATALYTIC CONVERTOR OPERATING PRECAUTIONS Hyundai Coupe models are fitted with catalytic convertors which require special operating con-siderations. The catalytic convertor serves tooxidize certain noxious elements of the exhaustgases leaving the engine to reduce the level ofpollutants emitted from the vehicle and, providedthat care is exercised to prevent damage, thecatalyst will operate efficiently for the life of thevehicle.It is of the utmost importance that the followinginformation is read and understood by the ve-
7
Catalytic Converter
SSA7020A