2003 Hyundai Coupe engine

CONTROLS AND EQUIPMENT
1- 4
HGK099-D
B040G01GK-GAT Central Door Lock The central door locking is operated by pushing the driver's door lock switch toward the front orrear of the vehicle. If the passenger door is openwhen the switch is pushed, the door will remainlocked when closed. NOTE:
o When pushing the switch toward the rear, all doors will unlock.When pushing the switch toward the front,all doors will lock.
o When the door is unlocked, the red mark on the switch is visible.
o The central door locking is operated by turning the key (driver's door only) towardthe front or rear of the vehicle. B070A01A-AAT THEFT-ALARM SYSTEM (Not all models) This system is designed to provide protection from unauthorized entry into the car. This systemis operated in three stages: the first is the "Armed"stage, the second is the "Alarm" stage, and thethird is the "Disarmed" stage. If triggered, thesystem provides an audible alarm with blinkingof the turn signal light.
B070C01GK-EAT Alarm StageThe alarm will be activated if any of the following occur while the car is parked and the system isarmed.
1) A front door is unlocked and opened withoutusing the transmitter.
2) The hatchback door is opened without using the key.
3) The engine bonnet is opened.The siren will sound and the turn signal lamp will blink continuously for 30 seconds. To turn off thesystem, unlock the door with the transmitter. CAUTION: Avoid trying to start the engine while thesystem is armed.
B070B02GK-EAT Armed Stage Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the ignition
switch.
2) Make sure that the engine bonnet and hatch- back door are closed.
3) Lock the doors using the transmitter of the keyless entry system.
After completion of the steps above, the turn signal lamp will blink once to indicate that thesystem is armed. NOTE:
1) If any door, hatchback door or engine bonnet remains open, the system will notbe armed.
2) If this happens, rearm the system as de- scribed above. 3) Once the system is armed, only the hatch-
back door may be unlocked using the keywithout disarming the system.
CAUTION:Do not arm the system until all passengershave left the car. If the system is armed whilea passenger(s) remains in the car, the alarmmay be activated when the remainingpassenger(s) leaves the car.

CONTROLS AND EQUIPMENT1- 21
A fully inflated airbag in combination with a prop- erly worn seat belt slows the driver's or thepassenger's forward motion, thus reducing therisk of head and chest injury.After complete inflation, the airbag immediatelystarts deflating, enabling the driver to maintainforward visibility.
Passanger's Airbag
B240B01GK-D
CAUTION: Do not install or place any accessories (drinkholder, cassette holder, sticker, etc) on thefront passenger's panel above the glove boxin the vehicle with passenger's side air bag.Such objects may become dangerous pro-jectiles and cause injury if the passenger'sside air bag inflates. Upon deployment, tear seams molded directly into the pad covers will separate under pressurefrom the expansion of the airbags. Further open-ing of the covers then allows full inflation of theairbags.
The airbag modules are located both in thecentre of the steering wheel and in the frontpassenger's panel above the glove box. Whenthe SRSCM detects a considerable impact to thefront of the vehicle, it will automatically deploy theairbags.
B240B01GK-AAT SRS Components and Functions The SRS consists of the following components: - Driver's Side Airbag Module - Passenger's Side Airbag Module- SRS Service Reminder Indicator (SRI)- SRS Control Module (SRSCM) The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontalor near-frontal impact is severe enough to re-quire airbag deployment. The SRS service reminder indicator (SRI) on the instrument panel will blink for about 6 secondsafter the ignition key is turned to the "ON" positionor after the engine is started, after which the SRIshould go out.
B240B02L-D
B240B03L-D
B240B01L-D

CONTROLS AND EQUIPMENT
1- 22
WARNING:
o When the SRS is activated, there may be a loud noise and fine dust will be releasedthroughout the vehicle. These conditionsare normal and are not hazardous. How-ever, the fine dust generated during airbagdeployment may cause skin irritation.Wash your hands and face thoroughlywith lukewarm water and a mild soap afteran accident in which the airbags weredeployed.
o The SRS can function only when the igni- tion key is in the "ON" position. If the SRSSRI does not come on or illuminatescontinuously when the ignition key isturned to "ON", or continuously remainson after flashing for about 6 seconds whenthe ignition key is turned to the "ON"position, or after the engine is started,comes on while driving, the SRS is notworking properly. If this occurs, have yourvehicle immediately inspected by yourHyundai dealer.
o Before you replace a fuse or disconnect a battery terminal, turn the ignition key tothe "LOCK" position or remove the igni-tion key. Never remove or replace the airbag related fuse(s) when the ignition keyis in the "ON" position. Failure to heed thiswarning will cause the SRS SRI to illumi-nate.
FUD1115A
CAUTION: When installing a container of liquid air fresh-ener inside a vehicle, do not place it near theinstrument cluster nor on the instrument panelpad surface. If there is any leakage from theair freshener onto these areas (instrumentcluster, instrument panel pad or air ventila-tor), it may damage these parts. If the liquidfrom the air freshener does leak onto theseareas, wash them with water immediately. Your Hyundai is equipped with a side airbag ineach front seat. The purpose of the airbag is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seatbelt alone. The side impactairbags are designed to deploy only during cer-tain side-impact collisions, depending on thecrash severity, angle, speed and point of impact.The air bags are not designed to deploy in all sideimpact situations. WARNING:
o The side impact airbag is supplemental to
the driver's and the passenger's seat beltsystems and is not a substitute for them.Therefore your seat belts must be worn atall times while the vehicle is in motion. Theairbags deploy only in certain side impactconditions severe enough to cause sig-nificant injury to the vehicle occupants.
B990B04Y-AAT Side Airbag (Not all models)
B990B01L.DAG

CONTROLS AND EQUIPMENT
1- 24
o If components of the airbag system must
be discarded, or if the vehicle must be scrapped, certain safety precautions mustbe observed. Your Hyundai dealer knowsthese precautions and can give you thenecessary information. Failure to followthese precautions and procedures couldincrease the risk of personal injury.
o If you sell your vehicle, be sure to inform the new owner of these important pointsand make certain that this manual istransferred to the new owner togetherwith the vehicle.
o If your car was flooded and has soaked carpeting or water on flooring, youshouldn't try to start engine; have cartowed to authorized Hyundai dealer.

CONTROLS AND EQUIPMENT1- 27
SB210K1-E
OIL PRESSURE WARNING LAMP
CAUTION: If the oil pressure lamp illuminates when the engine is running, an insufficient oil pressurelevel for continued safe operation of the en-gine exists. Continued operation of the en-gine in this condition may result in seriousengine damage. Under normal circumstances, the lamp will illu- minate when the ignition is turned "on" and will beextinguished when the engine is started.If the oil pressure warning lamp illuminates whilstthe engine is running, stop the engine immedi-ately and check the engine oil level. If the level isinsufficient, add the required amount of oil asindicated by the engine oil dipstick. If the lampfails to extinguish when the engine is restarted,do not continue to operate the vehicle.If the oil pressure lamp illuminates during normaloperation and the cause is not an insufficient oillevel, or the lamp fails to illuminate when theignition is turned "on", contact the nearest Hyundaidealer before further operating the vehicle.
SB210G1-E TURN SIGNAL INDICATOR LAMPS
Operation of a turn signal is indicated by the warning lamp located in the instrument cluster. Ifthe lamp fails to illuminate or does not flash, amalfunction within the turn signal system is indi-cated.
SB210J1-E HIGH BEAM INDICATOR LAMP
The high beam indicator lamp will illuminate whenever the headlamps are switched to highbeam of flash position.
260P02Y-EAT
ABS SERVICE REMINDER IN- DICATOR (Not all models)
When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on andthen go off in a few seconds. If the ABS SRIremains on, comes on while driving, or does notcome on when the key is turned to the "ON"position, this indicates that there may be a prob-lem with the ABS.If this occurs, have your vehicle checked by yourHyundai dealer as soon as possible. The normalbraking system will still be operational, but with-out the assistance of the anti-lock brake system. WARNING:If the both ABS SRI and Parking Brake/Brakefluid level warning lights remain "ON" orcome on while driving, there may be a prob-lem with E.B.D (Electronic brake force distri-bution).If this occurs, avoid sudden stops and haveyour vehicle checked by your Hyundai dealeras soon as possible.
B260B01GK-GAT
SRS (AIRBAG) SERVICE REMINDER INDICATOR (SRI)
The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after theignition key is turned to the "ON" position or afterthe engine is started, after which it will go out. This light also comes on when the SRS is not working properly. If the SRI does not come on orilluminates continuously when the ignition key isturned to "ON", or continuously remains on afterflashing for about 6 seconds when you turned theignition key to the "ON" position or started theengine, or if it comes on while driving, have theSRS inspected by an authorized Hyundai Dealer.

CONTROLS AND EQUIPMENT
1- 28 SB2100I-E
DOOR AJAR WARNING LAMP
The door ajar warning lamp indicates that a door is not correctly closed. Ensure that the lamp isextinguished prior to driving the vehicle.
SB210P1-E
LOW FUEL LEVEL WARNING LAMP
The low fuel warning lamp serves to warn the driver that the remaining fuel quantity is approxi-mately 9 litres and that the vehicle should berefuelled. If the vehicle is driven for an extendedperiod with the low fuel warning lamp illuminatedthere exists a possibility that misfiring due to fuel
becoming defective, approximately fifty per centof the normal braking performance will be avail-able.If failure of one of the circuits occurs, the requiredamount of pedal effort, pedal travel and stoppingdistance will be increased. Use of the gearbox isrecommended to assist in bringing the vehicle torest. The vehicle must not be driven once brakefailure has occurred until the system has beenrepaired and is functioning normally.The braking system employs a vacuum servo inorder that the pedal efforts are reduced. Powerfor the servo is derived from the engine andtherefore, in the event of the engine stopping orthe vehicle being towed, pedal efforts will besubstantially increased. SB210M1-E
CHARGING SYSTEM WARNING LAMP
The charging system warning lamp should illumi- nate when the ignition switch is turned to the"ON" position and should be extinguished whenthe engine is started. If the lamp fails to illuminatewhen the ignition is turned "ON" or fails to extin-guish after starting the engine, the nearestHyundai dealer should be contacted. If the lampilluminates whilst the vehicle is being driven, stopthe vehicle as soon as it is safe to do so andcheck the condition of the generator drive belt. Ifthe belt is in place and the tension is satisfactory,the advice of a Hyundai dealer should be sought.
B260H01GK-EAT PARKING BRAKE/BRAKE FLUID LEVEL WARNING LAMP
CAUTION: In the event of problems being suspected with the braking system, the advice of thenearest Hyundai dealer must be sought be-fore the vehicle is driven. Driving the vehiclewith either an electrical or hydraulic brakingsystem defect may be dangerous, resultingin accident or personal injury. Warning lamp operation The parking brake/brake fluid level warning lamp will be illuminated whenever the ignition switch isturned to the "ON" or "START" position when theparking brake is applied and must be extin-guished in a three seconds after the enginestarts.If the warning lamp fails to extinguish or illumi-nates at any other time, the vehicle must bebrought to rest in a safe location and the level ofbrake fluid in the reservoir checked. If the fluidlevel is incorrect, fluid conforming to DOT 3 orDOT 4 specifications should be added. If, aftercorrecting the brake fluid level, the warning lampcontinues to be illuminated, the advice of thenearest Hyundai dealer must be sought beforethe vehicle is driven again.The Hyundai Coupe is equipped with a diago-nally split dual braking system which will ensurethat in the event of one of the brake circuits SB210N2-E
HATCHBACK DOOR OPEN WARNING LAMP
The hatchback door warning lamp indicates when the hatchback door is open or is not fully closed.Ensure that the lamp has extinguished prior todriving the vehicle.CAUTION: If the drive belt (generator belt) is loose,broken, or missing while the vehicle is driv-ing, there may be a serious malfunction, en-gine could overheat because this belt alsodrives the water pump.

CONTROLS AND EQUIPMENT1- 29
SB210S1-E BRAKE PAD WEAR INDICATORThe front brake disc pads are fitted with an audible wear indicator which will cause a highpitched noise to be emitted when the remainingamount of friction lining is below the specifiedvalue. When the wear indicator is heard, thebrake pads should be replaced without delay toavoid damage occurring to the brake discs and asevere reduction in braking efficiency. SB215A1-E FUEL GAUGE The fuel gauge indicates the quantity of fuel remaining in the fuel tank. NOTE: The fuel gauge is not intended to give otherthan an approximate indication of the fuellevel and is unsuitable for the purposes ofcalculating fuel consumption figures.
B260N01GK-EAT
MALFUNCTION INDICATOR LAMP
This lamp illuminates when there is a malfunction of an exhaust gas related component, and the
system is not functioning properly so that theexhaust gas regulation values are not satisfied.This lamp will also illuminate when the ignition
key is turned to the "ON" position, and will go outafter engine starting. If it illuminates while driving,or does not illuminate when the ignition key isturned to the "ON" position, take your car to yournearest authorized Hyundai dealer and have thesystem checked.
shortage may occur. This situation must be avoided to prevent damage to the catalyst occur-ring. B260E01HP-GAT
SEAT BELT WARNING LIGHT (Not all models)
The seat belt warning light blinks for about 6 seconds when the ignition key is turned from the"OFF" position to "ON" or "START".
B260Q01E-GAT
CRUISE INDICATOR (Not all models)
The cruise indicator light in the instrument cluster is illuminated when the cruise control main switchon the end of the barrel is pushed.The indicator light does not illuminate when thecruise control main switch is pushed a secondtime.Information about the use of cruise control isbeginning on page 1-48.
HGK133
B265C01O-AAT Traction Control Indicator Lights (If installed)
The traction control indicators change operation according to the ignition switch position andwhether the system is in operation or not.They will illuminate when the ignition key isturned to the "ON" position, but should go outafter three seconds. If the TCS or TCS-OFFindicator stays on, take your car to your autho-rized Hyundai dealer and have the systemchecked. See section 2 for more informationabout the TCS.

CONTROLS AND EQUIPMENT
1- 30 SB215F1-E TACHOMETER
SB215B1-E ENGINE COOLANT TEMPERATURE GAUGE engine is hot may cause hot water and steam to be ejected from the radiator resulting inburns and scalding. The radiator cap mustonly be removed when the engine has cooled.Do not add cold water to a hot engine to avoidthe possibility of engine damage. The use ofplain water in the cooling system is not rec-ommended since the aluminium componentsof the cooling system require the use of acorrosion inhibitor found in the recommendedEthylene Glycol type anti freeze solutions.
The engine coolant temperature gauge indicatesthe engine coolant temperature and will, undernormal circumstances, give an indication in the"Normal" or centre portion of the scale. Shouldthe indication move into the upper or "Hot" por-tion of the scale, engine overheating is indicated.Under these circumstances, the vehicle shouldbe brought to rest as soon as is safe to do so andthe engine turned off. Once the engine has cooledsomewhat, the coolant level and the condition ofthe generator/water pump drive belt should bechecked. If the cause of the overheating cannotbe readily established, the assistance of aHyundai dealer should be sought. WARNING: The engine cooling system is pressurizedand removal of the radiator cap when the The tachometer registers the speed of the enginein revolutions per minute (R.P.M.). CAUTION: The maximum safe engine operating speed isindicated by the white zone of the tachometerscale. The engine should not be operatedbeyond the beginning of this zone or seriousengine damage may result.
SB215C1-E SPEEDOMETER
The speedometer indicates the vehicle speed in both miles and kilometres per hour.
HGK132HGK131A
HGK130B