Î
Î
Î
Î
T echnical Inf ormation
Specif ications
250
Engine Dimensions
WeightsCapacities
162.0 in (4,115 mm)
68.9 in (1,750 mm)
50.6 in (1,285 mm)
94.5 in (2,400 mm)
57.9 in (1,470 mm)
59.4 in (1,510 mm) 13.2 US gal (50
)
Water cooled 4-stroke DOHC
VTEC 4-cylinder gasoline engine
Type
BorexStroke
Displacement
Compression ratio
Spark plugs 121.8 cu-in (1,997 cm
)
11.0 : 1 1.72 US gal (6.5
)
2.01 US gal (7.6)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb. Fuel tank
Engine coolant
Engine oil
Manual
transmission
fluid
Differential
oil
Windshield
washer
reservoir5.1 US qt (4.8
)
4.8 US qt (4.5)
5.9 US qt (5.6)
1.6 US qt (1.5)
1.7 US qt (1.6)
0.78 US qt (0.74
)
0.81 US qt (0.77)
2.7 US qt (2.6)
4.4 US qt (4.2)
Including the coolant in the reserve tank and that remaining in the
engine.
Reserve tank capacity:
0.16 US gal (0.6
)
Excluding the oil remaining in the engine.
3.43 x 3.31 in (87.0 x 84.0 mm)
See the spark plug maintenance
section, page 180 .
Front
Rear
1:
2:Change
Total
Change
Total
Change
Total
Change
Total
U.S. Cars
Canadian Cars
1
2
Including filter
Without filter
µ
The treadwear grade is a compara-
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specif ied government
test course. For example, a tire
graded 150 would wear one and one-
half (1 1/2) times as well on the
government course as a tire graded
100. The relative perf ormance of
tires depends upon the actual condi-
tions of their use, however, and may
depart signif icantly f rom the norm
due to variations in driving habits,
service practices and dif f erences in
road characteristics and climate.
The tires on your vehicle meet all
U.S. Federal Saf ety Requirements.
All tires are also graded f or
treadwear, traction, and temperature
perf ormance according to
Department of Transportation
(DOT) standards. The f ollowing
explains these gradings.
Quality grades can be f ound where
applicable on the tire sidewall
between the tread shoulder and the
maximum section width. For
example:
The traction grades, f rom highest to
lowest, are AA, A, B, and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured
under controlled conditions on
specif ied government test surf aces
of asphalt and concrete. A tire
marked C may have poor traction
perf ormance.
Warning: The traction grade
assignedtothistireisbasedon
straight-ahead braking traction tests,
and does not include acceleration,
cornering, hydroplaning, or peak
traction characteristics.
All passenger car tires must conf orm
to Federal Saf ety Requirements in
addition to these grades.
T echnical Inf ormation
DOT T ire Quality Grading (U.S. Vehicles)
T readwear
Unif orm T ire Quality Grading T readwear 200
Traction AA
Temperature A Traction AA, A, B, C
252
µ
µ
µ
µµ
µ
µ
µµ
µ µ
The tires that came on your car have
a number of markings. Those you
should be aware of are described
below.
Whenever tires are replaced, they
should be replaced with tires of the
same size. Following is an example
tire size with an explanation of what
each component means.
Vehicletype(Pindicates
passenger vehicle).
Tire width in millimeters.
Aspect ratio (the tire’s section
height as a percentage of its
width).
Tire construction code (R
indicates radial). Load index (a numerical code
associated with the maximum
load the tire can carry). Rim diameter in inches.
Speed symbol (an
alphabetical code indicating
the maximum speed rating).
Tire Identif ication Number (TIN) is
a group of numbers and letters that
look like the f ollowing example TIN.
This indicates that the tire
meets all requirements of
the U.S. Department of
Transportation.Manuf acturer’s
identification mark.
Tire type code. Date of manuf acture.
P
55
R 16
DOT
B97R
FW6X2202
225 94
V
T echnical Inf ormation
Tire Inf ormation
Tire Labeling
Tire Size
T ire Ident if icat ion Number
254
DOT B97R FW6X 2202
P225/55R16 94V
