2003 HONDA S2000 reset

This indicator lights when you turn
the ignition switch ON (II). If it
comes on at any other time, it
indicates a problem in the
supplemental restraint system. For
complete inf ormation, see page .
This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II), and when
you push the START button. If this
light comes on at any other time,
there is a problem in the ABS. If this
happens, take the car to your dealer
to have it checked. With the light on,
your car still has normal braking
ability but no anti-lock.See page .
This light comes on if the trunk lid is
not closed tightly.
This light comes on if either door is
not closed tightly.
This light normally comes on when
you turn the ignition ON (II) and
goes of f af ter the engine starts. If it
comes on at any other time, there is
a problem in the Electric Power
Steering system. If this happens,
stop the car in a safe place and turn
of f the engine. Reset the system by
restarting the engine, and watch the
EPS light. If it does not go of f , or
comes back on again while driving,
take the car to your dealer to have it
checked. With the light on, the EPS
is turned off, making the car harder
to steer.
38
234
Supplemental Restraint
System Indicator
Anti-lock Brake System (ABS)
Indicator Malf unction Indicator
Lamp
Trunk-open Indicator
Door-open Indicator
Electric Power Steering
(EPS) Indicator
Indicator L ights
Inst rument s and Cont rols47
U.S. Canada

This shows how much f uel you have.
It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
whenyouaredrivingoncurvyor
hilly roads.The odometer shows the total dis-
tance your car has been driven. It
displays in miles and kilometers.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.
Gauges
Inst rument s and Cont rols
Fuel Gauge
Odometer
50
TRIP METER FUEL GAUGE
TRIP BUTTON
ODOMETER SELECT BUTTON
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

When the distance driven since the
last scheduled maintenance reaches
6,000 miles (9,600 km), the indicator
starts blinking. If you exceed 7,500
miles (12,000 km), the indicator
stays on.
Your dealer will reset the indicator
when they perf orm the scheduled
maintenance. If someone else
perf orms the maintenance, reset the
indicator yourself .
To reset the maintenance required
indicator, turn the ignition switch to
the LOCK position, then press and
hold the trip meter reset button
while you turn the ignition switch
ON. Continue holding the button
until the indicator resets (the
indicator light goes out).
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages and . This indicator reminds you that it is
time to take your car in for
scheduled maintenance.
This meter shows the number of
miles or kilometers driven since you
last reset it.
There are two trip meters, Trip A
and Trip B. Switch between Trip A
and Trip B by pressing the TRIP
button repeatedly. Each trip meter
works independently, so you can
keep track of two dif f erent distances.
To reset a trip meter, display it and
then press and hold the TRIP button
until you hear a beep and the
number resets to 0.0.
152 154
Inst rument s and Cont rols
Gauges
Maintenance Required Indicator
Trip Meter
51
MAINTENANCE REQUIRED INDICATOR

Your Honda’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The anti-thef t f eature will disable the
system if it is disconnected f rom the
vehicle’s battery. To get the system
working again, you must enter a
code number (see page ).114
AM/FM/CD Audio System
Audio System
Comf ort and Convenience Feat ures94
AM/FM BUTTON
TUNE KNOB
SEEK BAR STEREO INDICATOR
PWR/VOL KNOB

µ
µ The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
theSEEKbaror,then
release it. Depending on which part
of the SEEK bar you press, the
system scans upward or downward
f rom the current f requency. It stops
when it finds a station with a strong
signal.
The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pressing the PWR/
VOL knob or the AM/FM button.
Adjust the volume by turning the
knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the preset buttons. Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Turn the knob right or lef t until the
display reaches the desired
f requency.
CONT INUED
Operating the Radio SEEK
TUNE
Audio System
Comf ort and Convenience Feat ures95

µµ The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
Audio System
Comf ort and Convenience Feat ures
SCAN
Preset
96
TUNE KNOB
AM/FM BUTTON
STEREO INDICATOR
SCAN INDICATOR SCAN BUTTON
PWR/VOL KNOB SEEK/SKIP BAR PRESET BUTTONS
AUTO SELECT BUTTON

To store a f requency:Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s f requency is stored,
simply press and release the proper
Preset button to tune to it.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
1.
2.
3.
4.
CONT INUED
Audio System
Comf ort and Convenience Feat ures97
AM/FM BUTTON
SEEK BAR PRESET BUTTONS
TUNE KNOB

µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. Auto Select does not erase the
f requencies that you preset pre-
viously. When you return home, turn
of f Auto Select by pressing the
A. SEL button. The preset buttons
will then select the f requencies you
originally set.
To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations.
If you do not like the stations Auto
Select has stored, you can store
other f requencies in the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind the desired
f requencies, then store them in the
selected preset buttons as described
previously.
AUTO SELECT
Comf ort and Convenience Feat ures
Audio System
98
AUTO SELECT INDICATOR
SEEK BAR A. SEL BUTTONTUNE KNOB
SCAN BUTTON