2003 HONDA ELEMENT ignition

µUse this position f or
your normal driving. The transmis-
sion automatically selects a suitable
gear f or your speed and acceleration.
You may notice the transmission
shif ting up at higher speeds when
the engine is cold. This helps the
engine warm up f aster.
For f aster acceleration, you can get
the transmission to automatically
downshif t by pushing the accelerator
pedal to the f loor. The transmission
will shif t down one or two gears,
depending on your speed. Overdrive (O/D) is on whenever you
turn the ignition ON (II). You can
turn it of f by pressing the O/D
switch on the end of the shif t lever.
The O/D OFF indicator on the
instrument panel next to the shif t
lever ‘‘D’’ position indicator will come
on. Pressing the O/D switch again turns
the overdrive mode back on.
Overdrive can be turned on or of f
only when the ignition switch is ON
(II) and the shif t lever is in the D
position. Overdrive mode turns on
every time you start the engine, even
if you turned it of f the last time you
drove the vehicle.
CONT INUED
Automatic Transmission
Driving
Drive (D)Overdrive (O/D) Mode
181
OVERDRIVE OFF INDICATOR

µµ
The O/D OFF indicator also comes
on f or a f ew seconds when you turn
the ignition switch to ON(II). When overdrive is of f , the
transmission selects only the f irst
three gears. Turn the O/D of f to
provide engine braking when going
down a steep hill. You can also avoid
the transmission f rom cycling
between third and f ourth gears in
stop-and-go driving. To shif t to Second,
pressthereleasebuttonontheside
of the shif t lever. This position locks
the transmission in second gear. It
does not downshif t to f irst gear
when you come to a stop. Second
gives you more power when climbing,
and increased engine braking when
going down steep hills. Use second
gear when starting out on a slippery
surf ace or in deep snow. It will help
reduce wheelspin. If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
RPM below the red zone.
To shif t f rom Second to
First, press the release button on the
side of the shift lever. With the lever
in this position, the transmission
locks in f irst gear. By upshif ting and
downshif ting through 1, 2, and D,
you can operate this transmission
much like a manual transmission
without a clutch pedal.
If you shif t into First when the
vehiclespeedisabove31mph(50
km/h), the transmission shifts into
second gear f irst to avoid sudden
engine braking.
Automatic Transmission
Driving
Second (2) Engine Speed L imiter
First (1)
182

This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
is also used to release the Reverse
Lockout.Put a cloth on the edge of the Shif t
Lock Release slot cover next to
theshiftlever.Useasmallflat-
tipped screwdriver or small metal
plate (neither are included in the
tool kit) to remove the cover.
Caref ully pry on the edge of the
cover. To release the Reverse Lockout,
make sure the ignition switch is in
the ACCESSORY(I) position. Make sure the ignition switch is in
the LOCK (0) position. Set the Parking brake. Insert a screwdriver in the Shif t
Lock Release slot.
If you need to use the Shif t Lock
Release, it means your vehicle is
developing a problem. Have the
vehicle checked by your Honda
dealer.
Push down on the screwdriver
while you press the release button
on the side of the shif t lever and
move the shift lever out of Park to
Neutral.
To release the Reverse Lockout,
move the shift lever from Neutral
to Reverse, then to Park. Remove the screwdriver f rom the
Shif t Lock Release slot, then
install a new cover. Make sure the
notchonthecoverisontheright
side. Press the brake pedal, and
restart the engine.
1.
2.
3.
4.
5.
6.
Shif t L ock Release
Automatic Transmission
Driving183
COVER
SHIFT LOCK RELEASE SLOT

When purchasing a tow bar, make
sure you select a reputable
manuf acturer and installer. Follow
the manufacturer’s attachment
instructions caref ully. Your Element can be towed behind a
motorhome at legal highway speeds
up to 65 mph(100 km/h). Do not
exceed 65 mph (100km/h).
Otherwise, severe transmission
damage will occur. To avoid damage
to the 4WD system, it must be towed
with all f our wheels on the ground
(f lat towing).
After attaching the tow bar to your
motorhome, do the following to
prepare your Element f or ‘‘f lat
towing’’:When preparing to tow your
Element, make sure the
transmission is f illed to the correct
level (see page ). Do not
overf ill.
When preparing to tow your Element,
make sure the transmission is f ull of
fluid (see page ). Maintaining
the correct level is very important.
Do not overf ill. Do the f ollowing
Follow the procedure exactly.
Otherwise, severe automatic
transmission damage will occur.
Release the parking brake.
Shif t the transmission to Neutral.
Leave the key in the ignition
switch and the ignition switch in
ACCESSORY (I) so the steering
wheel does not lock. Make sure
the radio and any items plugged
into the accessory power sockets
are turned of f so you do not run
down the battery. 232
231
every day immediately bef ore you begin
towing.
5-speed Manual T ransmission A ut omat ic T ransmission
Towing Your Vehicle Behind a Motorhome
Driving198

Start the engine.
Press on the brake pedal. Shif t the
lever through all the positions (P,
R, N, D, 2, 1)
ShifttoD,thentoN.Letthe
engine run f or three minutes, then
turn of f the engine.
Release the parking brake.
Leave the ignition switch in
ACCESSORY (I) so the steering
wheel does not lock. Make sure
the radio and any items plugged
into the accessory power sockets
are turned of f so you do not run
down the battery.If you tow more than 8 hours in one
day, you should repeat the above
procedure at least every 8 hours.
(when you stop f or f uel, etc.)
If you tow a Element with an
automatic transmission, the
transmission f luid must be changed
every two years or 30,000 miles
(48,000 km), whichever comes f irst.Ext ended T owing
Towing Your Vehicle Behind a Motorhome
Driving199
Failure to f ollow the above instructions
exactly will result in severe automatic
transmission damage. If you cannot
shif t the transmission or start the
engine, your vehicle must be
transported on a f lat-bed truck or
trailer. The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in Accessory (I), and
make sure the steering wheel turns
f reely bef ore you begin towing.Severe automatic transmission damage
will occur if the vehicle is shif ted f rom
reverse to neutral and then towed with
the drive wheels on the ground.

CONT INUED
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
Draining the coolant requires access
to the underside of the vehicle.
Unless you have the tools and
knowledge, you should have this
maintenance done by a skilled
mechanic.Turn the ignition ON (II). Turn
the heater temperature control
dial f ully clockwise. Turn the
ignition of f .
Openthehood.Makesurethe
engine and radiator are cool to the
touch. Remove the radiator cap.
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard.
1.
2. 3.
4.
Replacing Engine Coolant
Cooling Syst em
Maint enance227

Clean off any dirt and oil that have
collected around the ignition coils.
Use a wrench to remove the bolt
holding the ignition coil. Pull the
ignition coil up slightly.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.Remove the ignition coil.
Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket.
Put the new spark plug into the
socket, then screw it into the hole.
Screw it in by hand so you do not
crossthread it.
Remove the f our nuts with a
wrench, then remove the coil
cover.
The spark plugs in your vehicle are a
special iridium-tipped design f or
longer lif e. The spark plugs should
be replaced according to the distance
recommendation in the maintenance
schedule.
1.
6.
7. 5.
2.
4. 3.
Replacement
Spark Plugs
Maint enance238
NUTS
NUTSBOLT
CONNECTOR
IGNITION COIL LOCK TAB
COIL COVER

Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque:Connect the wire connector to the
ignition coil. Make sure it locks in
place.
Push the ignition coil down all the
way. Install the bolt.
Repeat this procedure f or the
other three spark plugs.
Reinstall the coil cover, and
tighten the f our nuts. Install the ignition coil into the
hole.NGK:
DENSO:
8. 9.
10.
11.
12.
13. Specif ications:
Spark Plugs
Maint enance239
13 lbf·ft (18 N·m , 1.8 kgf·m)
IZFR6K-11
SKJ20DR-M11
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.