2003 HONDA CIVIC HATCHBACK open hood

Bef ore you begin driving your Honda,
youshouldknowwhatgasolineto
use, and how to check the levels of
important f luids. You also need to
know how to properly store luggage
or packages. The inf ormation in this
section will help you. If you plan to
add any accessories to your car,
please read the inf ormation in this
section f irst..............................
Break-in Period . 128
.........................................
Gasoline . 128
.........
Service Station Procedures . 129
................
Filling the Fuel Tank . 129
....................
Opening the Hood . 130
...............................
Oil Check . 132
.........
Engine Coolant Check . 133
...............................
Fuel Economy . 134
.....................
Vehicle Condition . 134
...........................
Driving Habits . 134
...
Accessories and Modif ications . 135
.............................
Carrying Cargo . 137
Bef ore Driving
Bef ore Driving 127

Shift to Park or Neutral and set
the parking brake. Pull the hood
release handle located under the
lower lef t corner of the dashboard.
The hood will pop up slightly.
Push the f uel f ill door closed until
it latches.
Stop f illing the tank af ter the f uel
nozzle automatically clicks of f . Do
not try to ‘‘top of f ’’ the tank, leave
some room f or the f uel to expand
with temperature changes.
Your car has an on-board ref ueling
vapor recovery system to help
keep f uel vapors f rom going into
the atmosphere. If the fuel nozzle
keeps clicking of f even though the
tank is not f ull, there may be a
problem with this system. Consult
your dealer.
Screw the f uel f ill cap back on,
tighten it until it clicks several
times. If you do not properly
tighten the cap, the Malfunction
Indicator Lamp may come on (see
page ).
Put the attachment on the fuel fill
cap into the slit on the f uel f ill door.
1.
5. 6.
4.
236
Service Station Procedures
Bef ore Driving Opening the Hood
130 ATTACHMENT
SLIT FUEL FILL CAP HOOD RELEASE HANDLE

CONT INUED
Pull the support rod out of its clip
and insert the end into the hole on
theleftsideof thehood.
To close the hood, lif t it up slightly to
remove the support rod f rom the
hole. Put the support rod back into
its holding clip. Lower the hood to
about a f oot (30 cm) above the
fender,thenletitdrop.
If you can open the hood without
lifting the hood latch handle, or the
hood latch handle moves stif f ly or
does not spring back as bef ore, the
mechanism should be cleaned and
lubricated (see page ).
Standing in f ront of the car, put
your f ingers under the f ront edge
of the hood to the right of center.
Slide your hand to the lef t until
you f eel the hood latch handle. Lif t
up on this handle until it releases
the hood. Lif t the hood. 3.
2. 181
Service Station Procedures
Bef ore Driving
131
LATCH
CLIP SUPPORT ROD
GRIP

Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available from your
Honda dealer) is required to
remove the f ilter.
Install a new oil f ilter according to
instructions that come with it.
Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Run the engine until it reaches
normal operating temperature,
then shut it off.
Always change the oil and f ilter
accordingtothetimeanddistance
(miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and f ilter collect contami-
nants that can damage your engine if
they are not removed regularly.
Tightening torque:
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
mechanic.
1. 2.
4.
3.
CONT INUED
Changing the Oil and Filter
Engine Oil
Maint enance
169
OIL DRAIN BOLT WASHER
OIL FILTER
9 lbf·ft (12 N·m , 1.2 kgf·m)

Remove the radiator cap.
Turn the ignition ON (II). Turn
the temperature control dial to
maximum heat. Turn of f the
ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
Bef ore draining the coolant,
remove the cover under the
radiator.
Use a Phillips-head screwdriver to
remove the two bolts, and remove
the nine holding clips f rom the
cover (5 clips on the bottom and 4
clips on the side) with a f lat-tipped
screwdriver. Then pull the cover
away.
Draining the coolant requires access
to the underside of the vehicle.
Unless you have the tools and
knowledge, you should have this
maintenance done by a skilled
mechanic. 1.
3.
2.
CONT INUED
Replacing Engine Coolant
Cooling Syst em
Maint enance 173

Open the hood.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Your car has halogen headlight
bulbs, one on each side. When
replacing a bulb, handle it by its steel
base and protect the glass from
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
cargo area, readjustment may be
required. Adjustment of the
headlights should be perf ormed by a
Honda technician or other qualif ied
mechanic.
1. 2.
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance
202 BULB WEATHER SEAL
HOLD-DOWN WIRE CONNECTOR
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Open the hood. The f ront parking
light is next to the headlight bulb.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Place the tabbed end of the side
marker assembly into the bumper
f irst, then the looped end. Press on
the looped end to get the assembly
to snap back in place.
Testthelightstomakesurethe
new bulb is working.
Put the socket back into its hole in
the lens and turn it clockwise until
it locks.
Push the new bulb straight into
the socket until it bottoms.
Pull the bulb straight out of its
socket.
Turn the socket one-quarter turn
counterclockwise to remove it
from the lens.
Turn on the parking lights and
check that the new bulb is
working.
1. 2. 3. 4. 5.
3. 4. 5. 6.
2.
Replacing a Front Parking L ight Bulb
Lights
Maint enance205
BULB
SOCKET

´´
To jump start your car, f ollow these
directions closely:
Open the hood and check the
physical condition of the battery
(see page ). In very cold
weather, check the condition of
the electrolyte. If it seems slushy
or like ice, do not try jump starting
until it thaws.
Turn of f all the electrical acces-
sories: heater, A/C, stereo system,
lights, etc.
Put the transmission in Neutral or
Park, and set the parking brake. Connect one jumper cable to the
positive ( ) terminal on your
Honda’s battery. Connect the
other end to the positive ( )
terminal on the booster battery.
If your car’s battery has run down,
you may be able to start the engine
by using a booster battery. Although
this seems like a simple procedure,
you should take several precautions.
1. 2.3.
184
T aking Care of t he Unexpect ed
Jump Starting
230 A battery can explode if you do
not follow the correct procedure,
seriously injuring anyonenearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.