2003 HONDA ACCORD SEDAN drain bolt

Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available from your
Honda dealer) is required to
remove the f ilter.Install a new oil f ilter according to
instructions that come with it.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
(4-cylinder models)
(6-cylinder models)
4.
5.
3.
2.
CONT INUED
Engine Oil
Maint enance271
WASHER
4-cylinder models WASHER
6-cylinder models OIL FILTER
4-cylinder models
OIL DRAIN BOLT OIL DRAIN BOLT
29 lbf·ft (39 N·m , 4.0 kgf·m) 33 lbf·ft (45 N·m , 4.6 kgf·m)

Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick. Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
The coolant you add should always
be a mixture of 50 percent antif reeze
and 50 percent water. Never add
straight antif reeze or plain water.
9. 8. 7.
6. (4-cylinder models)
(6-cylinder models) A dding Engine Coolant
Engine Oil, Cooling Syst em
Maint enance272
OIL FILTER
6-cylinder models
4-cylinder modelsRESERVE TANK
4.4 US qt (4.2)
4.5 US qt (4.3
) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Drain the coolant
into an appropriate container.Remove the reserve tank
mounting bolt with a wrench.
3.
4.
Maint enance
Cooling Syst em
276
4-cylinder modelsDRAIN
PLUG DRAIN PLUG
6-cylinder models MOUNTING
BOLT
RESERVE TANK
4-cylinder models RESERVE
TANK CAP
HOLDERS

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder. Install the
mounting bolt.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
5.
6. 7.
CONT INUED
Maint enance
Cooling Syst em
277
4-cylinder models
RESERVE
TANK CAP
RESERVE
TANK
6-cylinder models HOLDERS
MOUNTING
BOLT
FILLER NECK
Fill up to hereFILLER NECK
6-cylinder models Fill up to here

If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives and continued use can
cause stif f er shif ting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to add f luid,
contact your Honda dealer.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual Transmis-
sion Fluid (MTF) until it starts to
run out of the hole. Reinstall the
f iller bolt and tighten it securely.
6.
5-speed Manual Transmission
T ransmission Fluid
Maint enance283
FILLER BOLT
Correct level