2003 FORD MUSTANG Mounting

with header.
z Convertible top
flapping with the
top up z
Vinyl top contacting
interior headliner. z
Working from front to
back, INSTALL a 6.35 mm
(0.25 in) foam sheet
between the headliner
and the vinyl top at the
suspected area. Allow a
clearance of 50 mm (2 in)
-75 mm (3 in) away from
the roof bows and the side
rails.
z Noise from roof
rack z
Roof rack rails or
crossbars loose. z
TIGHTEN the fasteners.
z Roof rack fasteners
missing. z
INSTALL the approved
fasteners.
z Roof rack crossbars
installed backward. z
REINSTALL the
crossbars.
z Roof rack rub strips
partially lifting from
roof. z
REAPPLY adhesive or
fasteners or INSTALL new
rub strips as necessary.
z Roof rack gaskets
loose or misaligned. z
REINSTALL the gasket.
z Wind noise from
bug
shield/exterior
windshield sun
visor z
Turbulence created by
location and shape. z
REMOVE per customer
direction if it is a dealer
installed option. Symptom Chart—
Brake Noise/Vibration Condition
Possible Sources Action
z Rattling noise zCaliper
mounting bolts
loose. z
CHECK the caliper bolts.
TIGHTEN to specifications.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Damaged or
worn caliper
pins or
retainers. z
CHECK the caliper pins
and retainers for lubrication
and correct fit. LUBRICATE
or INSTALL new
components as necessary.
z Missing or
damaged anti-
rattle clips or
springs. z
CHECK the brake pads for
missing clips or broken
springs. INSTALL new
components as necessary.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Loose brake
disc shield. z
TIGHTEN the brake disc
shield bolts to specification.
REFER to Section 206 - 03 .
z Clicking noise— with
brakes applied with
ABS brakes z
ABS hydraulic
control unit. z
Acceptable condition.
z Squealing noise— zDisc brake zAcceptable condition. Klj . 16 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

CARRY OUT a driveline
vibration test. REFER to
Section 205
- 00 . REPAIR as
necessary.
z Binding or
damaged
splines on the
driveshaft slip-
yoke. z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for wear or damage.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REFER to
Section 205 - 01 . REPAIR as
necessary.
z Driveshaft
runout. z
CARRY OUT a Runout
Check. REFER to Section 205 - 00 . REPAIR as
necessary.
z Incorrect lateral
and radial
tire/wheel
runout. z
INSPECT the tire and
wheels. MEASURE tire
runouts. REPAIR or
INSTALL new components
as necessary. REFER to
Section 204 - 04 .
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Incorrectly
seated CV joint
in the front
wheel hub. z
CHECK the outer CV joint
for correct seating into the
hub. REPAIR as necessary. Symptom Chart —
Engine Noise/Vibration Condition
Possible Sources Action
z Grinding noise—
occurs during
engine cranking z
Incorrect starter
motor mounting. z
INSPECT the starter motor
for correct mounting.
REPAIR as necessary.
REFER to Section 303 - 06 .
z Starter motor. zCHECK the starter motor.
REPAIR or INSTALL a new
starter motor as necessary.
REFER to Section 303 - 06 .
z Incorrect starter
motor drive
engagement. z
INSPECT the starter motor
drive and flexplate/flywheel
for wear or damage.
INSTALL a new starter
motor drive or flywheel as
necessary. REFER to
Section 303 - 06 .
z Engine ticking
noise z
Fuel injector.
z Fuel line.
z Oil pump.
z Valve lifter.
z Belt tensioner.
z Water pump.
z Obstruction of cooling
fan. z
Go To Pinpoint Test B .
z Engine drumming zPowertrain mount. zCARRY OUT Klj . 23 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REFILL as necessary.
z Power steering pump
brackets loose or
misaligned. z
CHECK bolts, brackets
and bracket alignment.
TIGHTEN bolts to
specification. REPAIR
or INSTALL new
brackets as necessary.
REFER to Section 211 -
02 .
z Steering gear clunk
— occurs only
while cornering
over a bump (can
be temperature
sensitive) z
Steering gear. zINSPECT the steering
gear for loose mounting
bolts. TIGHTEN as
necessary. REFER to
Section 211 - 02 .
z Feedback (rattle,
chuckle or
knocking noise in
the steering gear)
— a condition
where roughness is
felt in the steering
wheel when the
vehicle is driven
over rough
surfaces z
Column
intermediate/flexible
shaft joints damaged or
worn. z
INSTALL a new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Loose, damaged or
worn tie- rod ends. z
TIGHTEN the nuts to
specification or
INSTALL new tie- rod
ends as necessary.
REFER to Section 211 -
02 .
z Steering gear
insulators or mounting
bolts loose or
damaged. z
TIGHTEN the bolts or
INSTALL new bolts as
necessary. REFER to
Section 211 - 02 .
z Steering column
intermediate shaft bolts
are loose. z
TIGHTEN the bolts to
specification. REFER to
Section 211 - 04 .
z Steering column
damaged or worn. z
REPAIR or INSTALL a
new steering column as
necessary. REFER to
Section 211 - 04 .
z Loose suspension
bushings, bolts or ball
joints. z
INSPECT the
suspension system.
TIGHTEN or INSTALL
new components as
necessary. REFER to
Section 204 - 01 .
z Feedback (nibble
at the steering
wheel) — a
condition where
slight rotational
movement is felt in
the steering wheel
when the vehicle is
driven over rough
or grooved z
Lateral runout in the
tire or wheel. z
GO to Pinpoint Test H . Klj . 34 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

01 .
z Damaged or
worn suspension
components. z
INSPECT the suspension
components for wear or
damage. REPAIR as
necessary.
z Loose wheel
nuts. z
CHECK the wheel nuts.
TIGHTEN to specification.
REFER to Section 204 -
04 .
z Damaged or
uneven tire wear. z
SPIN the tire and CHECK
for abnormal tire wear or
damage. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire shimmy or
shake— occurs at
lower speeds z
Wheel/tire out of
balance. z
BALANCE the wheel/tire
assembly.
z Uneven tire wear. zCHECK for abnormal tire
wear. INSTALL a new tire
as necessary. REFER to
Section 204 - 04 .
z Excessive radial
runout of wheel
or tire. z
CARRY OUT a radial
runout test of the wheel
and tire. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Worn or
damaged wheel
studs or
elongated stud
holes. z
INSPECT the wheel studs
and wheels. INSTALL new
components as necessary.
REFER to Section 204 - 01
for the front wheels or
Section 204
- 02 for the rear
wheels.
z Excessive lateral
runout of the
wheel or tire. z
CARRY OUT a lateral
runout test of the wheel
and tire. CHECK the
wheel, tire and hub.
REPAIR or INSTALL new
components as necessary.
z Foreign material
between the
brake disc and
hub or in the
brake disc fins. z
CLEAN the mounting
surfaces of the brake disc
and hub. CHECK the
brake disc fins for material.
z High speed shake or
shimmy—occurs at
high speeds z
Excessive wheel
hub runout.
z Damaged or
worn tires.
z Damaged or
worn wheel
bearings.
z Worn or
damaged
suspension or
steering linkage
components.
z Brake disc or
drum imbalance. z
Go To Pinpoint Test K . Klj . 39 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

information, REFER to
Section 205
- 00 .
REPAIR as necessary.
z Transmission
rumble/growl— noise at
all speeds in forward
gears, more
pronounced in a heavy
acceleration condition z
Damaged or worn
transmission
bearing or gears
(high mileage
vehicles). z
CHECK transmission
fluid for excessive
metal particles.
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transfer case whine—
noise at all ranges z
Incorrect fluid level
or fluid quality. z
CHECK that the
transfer case is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Worn oil pump. zDISASSEMBLE the
transfer case. CHECK
the oil pump for wear or
damage. REPAIR as
necessary.
z Under- inflated or
oversized tires. z
CONFIRM that the tires
and wheels are correct
for the vehicle. CHECK
that the tire inflation
pressures are correct.
z Transfer case
growl/rumble— noise at
all ranges (A small
amount of planetary
noise can be heard
when the transfer case
is operated in low
range.) z
Damaged or worn
bearings or
planetary gear. z
DISASSEMBLE the
transfer case. CHECK
the bearings or
planetary gear for wear
or damage. REPAIR as
necessary.
z Transfer case
scraping/grating—
noise at all ranges z
Excessively
stretched drive
chain hitting the
case. z
DISASSEMBLE the
transfer case. CHECK
the drive chain for wear
or damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at all
ranges or high range
only z
Worn or damaged
sun (input) gear,
clutch pack
(intermediate) gear
or output shaft gear. z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at
low range only z
Worn or damaged
intermediate gear
and sliding gears
(clutch pack). z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
vibration— vibration felt
with vehicle in 4WD z
Transfer case
mounting.
z Driveshaft out of
balance.
z Excessive pinion z
Go To Pinpoint Test M . Klj . 44 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST M: TRANSFER CASE VIBRATION the system for normal operation.
No
GO to
L6 .
L6 CHECK THE FLYWHEEL BOLTS
z
Check for loose flywheel bolts.
z Are the bolts loose? Yes
TIGHTEN the bolts to
specifications. REFER to
Section 308 - 01 . TEST the system for
normal operation.
No
GO to L7 .
L7 CHECK THE FLYWHEEL SURFACE
z
Inspect the flywheel surface for wear or damage.
Check the flywheel runout.
z Is there any damage or excessive wear? Yes
INSTALL a new flywheel. TEST
the system for normal operation.
No
Clutch system normal. CONDUCT
a diagnosis on other suspect
systems.
Test Step Result / Action to Take
M1 INSPECT THE TRANSFER CASE
z
WARNING: The electrical power to the air suspension
system must be shut off prior to hoisting, jacking or towing
an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can
result in unexpected inflation or deflation of the air springs,
which can result in shifting of the vehicle during these
operations.
z Inspect the transfer case for loose or missing mounting bolts.
Check for fluid seepage between the transfer case and the
transmission.
z Are the mounting bolts missing or loose? Yes
TIGHTEN to
specifications or
INSTALL new bolts as
necessary. TEST the
system for normal
operation.
No
GO to
M2 .
M2 INSPECT THE REAR DRIVESHAFT
z
NOTE: Verify that the driveshaft and pinion flange index marks
are aligned.
z Inspect the driveshaft for missing weights, damage or
undercoating.
z Inspect the U- joints for freedom of movement.
z Check driveshaft runout and, if necessary, check the pinion
flange runout.
z Is the driveshaft or U- joints worn or damaged or
misaligned? Yes
REPAIR or INSTALL a
new driveshaft as
necessary. TEST the
system for normal
operation.
No
GO to
M3 .
M3 CHECK THE DRIVELINE ANGLES
z
Measure the rear driveshaft and pinion angles. Refer to Section 205 - 00 .
z Measure the front driveshaft and pinion angles. Refer to Section 205 - 00 .
z Are the driveline angles incorrect? Yes
REPAIR as necessary.
TEST the system for
normal operation.
No Klj . 62 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. For vehicles with a two-
piece hub and brake disc assembly:
z Match-mark before disassembly.
z Remove the brake disc.
z Clean the hub and brake disc mounting surfaces with metal surface cleaner.
z Using a die grinder with a mild abrasive (Scotch Brite® type), remove any rust or
corrosion from the hub and brake disc mounting surfaces.
z Align the match- marks and reinstall the brake disc on the hub.
7. CAUTION: Do not use a bench lathe to machine brake discs.
NOTE: The depth of cut must be between 0.10 and 0.20 mm (0.004 and 0.008 inch). Lighter
cuts will cause heat and wear. Heavier cuts will cause poor brake disc surface finish.
Using an on- car brake lathe, machine the brake discs. Follow the manufacturer's instructions.
After machining, make sure the brake disc still meets the thickness specification.
8. Using the special tools, verify that the brake disc lateral runout is now within specification. For additional information, refer to Section 206 - 00 .
9. Remove the special tool hub adapter.
10. Remove any remaining metal chips from the machining operation.
11. For vehicles with a two- piece hub and brake disc assembly:
z Remove the brake disc from the hub.
z Remove any remaining metal chips from hub and brake disc mounting surfaces and from
the ABS sensor.
z Apply a liberal amount of lubricant to the hub flange, pilot area and to the brake disc- to-
hub mounting surface.
z Using the match marks, mount the brake disc on the hub.
12. Install the brake caliper anchor plate and the brake caliper.
13. Install the tire and wheel assembly.
14. Test the system for normal operation. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Camber and Caster Adjustment —
Front
All vehicles 1. Remove the rivet. Loosen the nuts and bolt.
Vehicles requiring camber adjustment 2. Move the front suspension camber adjusting plate (3B391) to the required camber setting.
Vehicles requiring caster adjustment 3. NOTE: If caster adjustment is necessary to resolve a pull, or out of specification cross- caster
split, then slotting the shock tower at the front shock absorber (18124) upper mounting point is
an acceptable method. This procedure should not be routinely performed with all alignments
and only after all other possible sources have been inspected and corrected as necessary.
Determine the amount of caster adjustment needed.
zIf no more than 0.6 degree is needed, only one shock tower needs to be slotted.
4. Mark the camber position of the front suspension camber adjusting plate (3B391).
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...