2003 FORD MUSTANG heating

SPECIFICATIONS
SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricant
MERPOL® ESE-
M99B144-
B PAG Refrigerant Compressor Oil (R-134a Systems) F7AZ-19589-
DA (Motorcraft
YN- 12-C) WSH-
M1C231- B
Torque Specifications Description Nm lb-
in Interior evaporator core housing bracket nut and bolts 8 71 Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Heating and Defrosting
The heating and defrosting system has the following features:
zControls the temperature and, during A/C operation, reduces the relative humidity of the air
inside the vehicle.
z Delivers heated or cooled air to maintain the vehicle interior temperature and comfort level.
z Controls the A/C blower motor speed.
z Cooling or heating can be adjusted to maintain the desired temperature.
z System uses a reheat method to provide conditioned air to the passenger compartment.
z The blower motor (19805) draws outside air through the air inlet duct from just below the
windshield during all system operations except for MAX A/C cooling (when recirculated air is
used).
z All airflow from the blower motor passes through the A/C evaporator core (19860).
z The temperature is then regulated by reheating a portion of the air and blending it with the
remaining cool air to the desired temperature.
z The temperature blending is varied by the air temperature control door, which regulates the
amount of air that flows through and around the heater core (18476), where it is then mixed and
distributed.
Heater Core
The heater core (18476) consists of fins and tubes arranged to extract heat from the engine coolant
and transfer it to air passing through the heater core. Blower Motor SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Heating and Defrosting
Refer to
Section 412 - 00 .
SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Blower Motor
Removal
1. Disconnect the jumper wire.
2. Disconnect the main harness.
3. Remove the screws. 4. Separate the cover from the motor. SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Evaporator Core Housing
Removal
NOTE:
The evaporator core is not separately serviceable, it is serviced only with the evaporator core
housing assembly.
1. Disconnect the battery ground cable.
2. Recover the refrigerant. For additional information, refer to Section 412 - 00 .
3. Drain the cooling system. For additional information, refer to Section 303 - 03A or
Section 303 -
03B .
4. Remove the instrument panel. For additional information, refer to Section 501 - 12 .
5. Disconnect the heater hose couplings from the heater core. For additional information, refer to Section 412 - 00 .
6. Disconnect the vacuum connector. SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Material
Item Specification
PAG Compressor Oil (R-134a
Systems)
F7AZ- 19589- DA (Motorcraft
YN- 12-C) WSH-
M1C231-
B MERPOL®
NA ESE-
M99B144-
B Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Heater Core
Removal
NOTE:
If a heater core leak is suspected, the heater core must be pressure leak tested before it is
removed from the vehicle. For additional information, refer to Section 412 - 00 .
1. Remove the evaporator core housing. For additional information, refer to Evaporator Core Housing in this section.
2. Remove the foam weather seal.
3. Remove the screws and remove the heater core cover.
4. Remove the heater core.
Installation 1. NOTE: Be sure to install a new oval foam weather seal around the heater core inlet and outlet
tubes.
To install, reverse the removal procedure.
SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY
Evaporator Core Housing
Disassembly
1. Remove the evaporator core housing. For additional information, refer to Evaporator Core Housing in this section.
2. Remove the foam weather seal.
3. Remove the screws and remove the heater core.
4. Remove the screws and remove the A/C recirculating air duct.
5. Remove the vacuum reservoir. 1. Disconnect the vacuum line.
2. Remove the screw.
SECTION 412-
02: Heating and Ventilation 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Control Components
Manual A/C
The climate control system heats or cools the vehicle interior depending on the function selector
position and the temperature selected. Function selector position determines heating or cooling and air
distribution. The temperature blend control setting determines air temperature.
The manual climate control components are used to:
zselect air inlet source (outside or recirculated).
z select blower motor speed.
z select discharge air temperature (temperature blend).
z select discharge air location (defrost, panel, floor).
z select A/C compressor clutch operation. Component Locations SECTION 412-
04: Control Components 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...