2003 FORD MUSTANG ignition

PINPOINT TEST O: THE BRAKE WARNING INDICATOR IS
NEVER/ALWAYS ON INDICATOR LAMP CONTROL III ACTIVE
COMMAND USING THE DIAGNOSTIC TOOL
z
Connect the diagnostic tool.
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster Active
Command.
z Select the instrument cluster INDICATOR
LAMP CONTROL III active command.
Trigger the CHECK FUEL CAP active
command ON. Observe the CHECK FUEL
CAP indicator.
z Does the CHECK FUEL CAP indicator
illuminate? Yes
REFER to the Powertrain
Control/Emissions Diagnosis (PC/ED)
manual.
No
GO to
N3 .
N3 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors
and make sure they seat correctly.
z Operate the system and verify the concern is
still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER
to
Instrument Cluster in this section. TEST
the system for normal operation.
No
The system is operating correctly at this
time. Concern may have been caused by a
loose or corroded connector. CLEAR the
DTCs. REPEAT the self- test. Test Step Result / Action to Take
O1 CHECK IF THE GEM IS RECEIVING THE CORRECT
IGNITION SWITCH STATUS CAUTION: Use the correct probe adapter(s) when
making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
z Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
Generic Electronic Module (GEM) PID.
z Monitor GEM PIDs IGN_KEY, IGN_S, IGN_R, and IGN_A
while cycling the ignition switch through all positions and
then removing the key from ignition switch.
z Do the PIDs agree with the ignition switch status? Yes
GO to
O2 .
No
REFER to Section 211 - 05 .
O2 DETERMINE IF GEM IS RECEIVING THE CORRECT
PARKING BRAKE INPUT z
Monitor GEM PID PRK_BRK while applying and releasing
the parking brake.
z Did the PID read ON with the parking brake applied, and
OFF with the parking brake released? Yes
GO to
O3 .
No
GO to O5 .
O3 DETERMINE IF BRAKE WARNING INDICATOR CIRCUIT IS
OPEN OR GROUNDED z
Verify that the parking brake is released.
z Is the instrument cluster BRAKE warning indicator off? Yes
GO to
O4 . Klj . 28 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Warning Devices
The warning device system consists of the following components:
zdoor ajar switches
z generic electronic module (GEM)
z key- in-ignition warning switch
z safety belt switch
z parklamp switch
SECTION 413-
09: Warning Devices 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Gauges And Warning Devices
Refer to Wiring Diagrams Cell
59 , Generic Electronic Module for schematic and connector
information.
Refer to Wiring Diagrams Cell 60 , Instrument Cluster for schematic and connector information.
Refer to Wiring Diagrams Cell 66 , Warning Chime for schematic and connector information.
Principles of Operation
Key- In-Ignition Warning Chime
The key- in-ignition warning chime activates when the generic electronic module (GEM) detects the
ignition switch circuits are in the OFF or ACC states and when the GEM detects the driver door is ajar
from the driver door ajar circuits. Refer to the Chime Duration Table in this section for audible output,
duration time, and priority ratings.
Airbag Warning Chime
The airbag warning chime activates when the GEM detects the ignition switch circuits are in the RUN
state and when the GEM detects a chime is requested from the airbag system circuit. Refer to the
Chime Duration Table for audible output, duration time, and priority ratings.
Door Ajar Warning Chime
The door ajar warning chime activates when the GEM detects the ignition switch circuits are in the
RUN state and when the GEM detects the driver or passenger door is ajar from the driver and
passenger door ajar circuits. Refer to the Chime Duration Table in this section for audible output,
duration time, and priority ratings.
Headlamps Left on Warning Chime
The headlamps left on warning chime activates when the GEM detects the ignition switch circuits are
in the KEYOUT state, when the GEM detects the driver door is ajar from the driver door ajar circuit, SECTION 413-
09: Warning Devices 2003 Mustang Workshop Manual Special Tool(s)
73III Automotive Meter
105-
R0057 or equivalent Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F048, or equivalent
diagnostic tool Klj . 1 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

and when the GEM detects the headlamps or parklamps are on from the exterior lamp circuits. Refer
to the Chime Duration Table in this section for audible output, duration time, and priority ratings.
Safety Belt Warning Chime
The safety belt warning chime and safety belt warning lamp activate when the GEM detects the
ignition switch circuits are in the RUN or START state and when the GEM detects the safety belt is
unbuckled from the safety belt circuit. The safety belt warning lamp indicator will prove out for three
seconds whenever the GEM detects that the ignition circuits make a transition to RUN from OFF, ACC,
or KEYOUT state. Refer to the Chime Duration Table in this section for audible output, duration time,
and priority ratings.
Belt Minder
NOTE:
Belt minder is a configurable item. If configuring using a diagnostic tool, refer to Section 418 -
01 . To configure without using a diagnostic tool, refer to
Belt Minder Deactivating/Activating in this
section.
The belt minder feature supplements the current safety belt warning function. The belt minder feature
is enabled after the current safety belt warning is complete. If the driver safety belt is not buckled
approximately five seconds after the safety belt warning light has turned off, the belt minder reminds
the driver that their safety belt is unbuckled by intermittently sound a chime and illuminating the safety
belt warning lamp in the instrument cluster. While activated, the belt minder alternates the chime and
indicator from on for six seconds to off for 30 seconds.
The belt minder reminder stops when:
zthe drive seat belt is buckled.
z the ignition is turned to OFF or ACC.
z five minutes have elapsed since belt minder has started.
Inspection and Verification
NOTE: Upon installation of a new GEM, the module must be reconfigured. For additional information,
refer to Section 418 - 01 .
1. The warning lamps are a GEM controlled system; refer to Section 419 - 10 .
2. Verify the customer concern by operating the system in question.
3. Visually inspect for the following obvious signs of mechanical and electrical damage.
Chime Duration Table Feature Audible Output Duration Priority
Safety belt Chime, 60/minute 740 Hz 6.0 seconds 1
Key-
in-ignition Chime, 120/minute 740 Hz Continuous 2
Headlamps left on Chime, 240/minute 740 Hz Continuous 3
Airbag Single tone, 1,000 Hz Continuous 4
Door ajar Single tone, 1,000 Hz 1.0 second 7 Klj . 2 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

4. If the concern remains after the inspection, connect the diagnostic tool to the data link connector
(DLC) located beneath the instrument panel and select the vehicle to be tested from the
diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
z check the connections to the vehicle.
z check the ignition switch position.
5. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool manual.
6. Carry out the Data Link Diagnostic Test. If the diagnostic tool responds with: zCKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z NO RESP/NOT EQUIP for RCM, refer to Section 501 - 20B .
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM.
7. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
8. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
9. If the DTCs retrieved are for the RCM, refer to Section 501 - 20B .
Visual Inspection Chart Mechanical Electrical
z
Switch(es) z
Central junction box (CJB) fuses:
„28 (15A)
„ 32 (15A)
„ 39 (5A)
z Circuitry
GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1340 Chime Input Request
Circuit Short to Ground GEM Go To Pinpoint Test C .
B1342 ECU Is Defective GEM CLEAR the DTCs. TEST the system for normal operation.
RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL
a new GEM. REFER to
Section 419 - 10 .
B1353 Ignition Key-
In Circuit
Open GEM Go To Pinpoint Test B .
B1462 Safety Belt Switch
Circuit Failure GEM Go To Pinpoint Test F . Klj . 3 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Symptom Chart
Symptom Chart Condition
Possible Sources Action
z No communication with the
generic electronic module
(GEM) z
Central junction box
(CJB) fuses:
„39 (5A).
„ 32 (15A).
z Circuitry.
z Generic electronic
module (GEM). z
Go To Pinpoint Test
A .
z The key- in-ignition chime does
not operate correctly z
Central junction box
(CJB) fuses:
„28 (15A).
„ 32 (15A).
z Central junction box
(CJB).
z Driver door ajar
switch.
z Key- in ignition
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
B .
z A chime does not operate
correctly— air bag z
Restraint control
module (RCM).
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
C .
z The door ajar chime does not
operate correctly z
Driver door ajar
switch.
z Passenger door ajar
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
D .
z The headlamp on reminder
chime does not operate
correctly z
Headlamp switch .
z Circuitry.
z Generic electronic
module (GEM).
z Driver door ajar
switch.
z Ignition switch. z
Go To Pinpoint Test
E .
z The safety belt warning chime
does not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F .
z The belt minder feature does
not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F . Klj . 4 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST B: THE KEY-
IN-IGNITION CHIME DOES NOT
OPERATE CORRECTLY z
Is the resistance less than 5 ohms? A3 CHECK CIRCUIT 397 (BK/WH) FOR SHORT TO POWER
z
Measure the voltage between the GEM C201b pin 4, circuit
397 (BK/WH), harness side and ground.
z Is any voltage present? Yes
REPAIR the circuit. TEST
the system for normal
operation.
No
REFER to
Section 418 - 00 .
Test Step Result / Action to Take
B1 CHECK IGNITION STATES
z
Connect the diagnostic tool.
z Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Monitor the GEM PIDS IGN_KEY, IGN_A, IGN_S, and IGN_R
while cycling the ignition switch through the OFF, ACC, RUN,
START and key out positions.
z Do the PID values agree with the ignition switch states? Yes
GO to
B2 .
No
GO to B4 .
B2 CHECK GEM INTERNAL TONE OPERATION
z
Enter the following diagnostic mode on the diagnostic tool:
GEM Active Command.
z Trigger the GEM Active Command CHIME ON and OFF.
z Does the chime operate correctly? Yes
GO to
B3 .
No
GO to B11 .
B3 CHECK GEM INPUT FROM DOOR AJAR CIRCUIT
z
Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Monitor the GEM PID D_DR_SW, while opening and closing
the driver door.
z Do the GEM PID D_DR_SW values indicate CLOSED and
AJAR correctly? Yes
GO to
B11 .
No
Go To Pinpoint Test D .
B4 CHECK GEM INPUT VOLTAGE FROM IGNITION SWITCH AT Klj . 6 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

CJB FUSE 28 (15A)
z
Disconnect: CJB Fuse 28 (15A).
z Measure the voltage between CJB fuse 28 (15A), pin 1,
harness side and ground while cycling the ignition switch
through all positions.
z Is the voltage greater than 10 volts in the RUN and START
positions only? Yes
GO to
B5 .
No
REPAIR the CJB.
REPEAT the self- test.
CLEAR the DTCs. B5 CHECK GEM INPUT VOLTAGE FROM IGNITION SWITCH AT
CJB FUSE 32 (15A) z
Disconnect: CJB Fuse 32 (15A).
z Measure the voltage between CJB fuse 32 (15A), pin 1,
harness side and ground while cycling the ignition switch
through all positions.
z Is the voltage greater than 10 volts in the RUN and ACC
positions only? Yes
GO to
B6 .
No
REPAIR the CJB.
REPEAT the self- test.
CLEAR the DTCs. B6 CHECK GEM VOLTAGE INPUT CIRCUITS FOR OPEN —
IGNITION SWITCH CIRCUIT 911 (WH/LG) z
Disconnect: CJB Fuse 28 (15A).
z Disconnect: GEM C201e.
z Insert the ignition key. Measure the resistance between GEM
C201e pin 8, circuit 911 (WH/LG), harness side and CJB Fuse
28 (15A) pin 2, circuit 911 (WH/LG), harness side.
z Is the resistance less than 5 ohms? Yes
GO to
B7 .
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. B7 CHECK GEM VOLTAGE INPUT CIRCUITS FOR OPEN —
IGNITION SWITCH CIRCUIT 1002 (BK/PK) Klj . 7 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...