2003 FORD MUSTANG power steering

end surface of the
power steering pump
rotor.
z Damaged or worn
power steering pump
rotor splines.
z A crack on the inner
surface of the power
steering pump cam.
z Interference between
the power steering
pump rotor and cam.
z Damaged or worn
power steering pump
rotor and pressure
plates. 02 .
z Power steering
pump swish noise z
Power steering fluid
flow into the bypass
valve of the pump
valve housing with fluid
temperature below 54°
C (130°F). z
Acceptable condition.
z Power steering
pump whine noise z
Aerated fluid. zPURGE the air from the
system. REFER to
Section 211 - 00 .
CHECK for a leak in the
system.
z Damaged power
steering pump cam. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Damaged valve cover
O-ring seal. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clicking
(mechanical) noise z
Power steering pump
rotor slippers too long,
excessive rotor slipper-
to-slot clearance or
damaged or worn rotor
assembly. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clatter noise z
Damaged corners on
the outside diameter or
the power steering
rotor or distorted rotor
slipper ring. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
Symptom Chart—
Suspension Noise/Vibration Condition
Possible Sources Action
z Squeak or grunt— noise
from the front suspension,
occurs more in cold
ambient temperatures.
More noticeable over
rough roads or when
turning z
Front stabilizer
bar insulators. z
Under these conditions,
the noise is acceptable.
CHECK TSBs. Klj . 36 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST C: ACCESSORY DRIVE BEARING HOOT
PINPOINT TEST D: POWER STEERING MOAN
PINPOINT TEST E: ENGINE DRIVEN COOLING FAN MOAN operating correctly?
No
INSTALL a new valve lifter/lash adjuster
(s). TEST the system for normal
operation.
Test Step Result / Action to Take
C1 CHECK THE IDLER AND TENSIONER
PULLEY BEARINGS z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Place an EngineEAR probe directly on the
pulley center post or bolt to verify which
bearing is making the noise.
z Key in OFF position.
z Is either bearing making the noise? Yes
INSTALL a new pulley/idler. CARRY OUT the
Vehicle Cold Soak Procedure and TEST the
system for normal operation.
No
CONDUCT a diagnosis on other suspect
accessory drive components.
Test Step Result / Action to Take
D1 CHECK THE POWER STEERING
SYSTEM z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Turn the steering wheel while the noise
is occurring and listen for changes in
sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
GO to
D2 .
No
CONDUCT a diagnosis on other suspect
accessory drive components. D2 VERIFY THE SOURCE
z
Key in START position.
z Place an EngineEAR probe near the
power steering pump/reservoir while the
noise is occurring. While an assistant
turns the steering wheel, listen for
changes in sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
VERIFY that the supply tube to the pump is
unobstructed. CHECK the fluid condition and
level. DRAIN the fluid and REFILL. CARRY
OUT the Vehicle Cold Soak Procedure and
TEST the system for normal operation. REFER
to Section 211
- 02 .
No
Normal system operation. Test Step Result / Action to Take
E1 CHECK THE ENGINE DRIVEN COOLING
FAN AFTER A COLD SOAK Klj . 51 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST I: REAR SUSPENSION NOISE z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the steering system for wear or damage. Carry out a
steering linkage test. Refer Section 211 - 00 .
z Inspect the tire wear pattern. Refer to Tire Wear Patterns
chart in this section.
z Are the steering components worn or damaged? REPAIR the steering
system. INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H3 .
H3 FRONT SHOCK ABSORBER/STRUT CHECK
z
Check the front shock absorbers/strut mounts for loose
bolts or nuts.
z Check the front shock absorbers/struts for wear or damage.
Carry out a "bounce test".
z Are the front shock absorbers/struts loose or
damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new front
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
H4 .
H4 CHECK THE FRONT SPRINGS
z
Check the front spring and front spring mounts/brackets for
wear or damage.
z Are the front springs or spring mounts/brackets worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H5 .
H5 CHECK THE CONTROL ARMS/RADIUS ARMS
z
Inspect the control arm bushings for wear or damage.
z Inspect for twisted or bent control/radius arm.
z Are the control/radius arms damaged or worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H6 .
H6 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step Result / Action to Take Klj . 54 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. While the noise is occurring, either place an EngineEAR probe near the IAC valve and the inlet
tube, or create a 6.35 mm (0.25 in)- 12.7 mm (0.50 in) air gap between the inlet tube and the
clean air tube. If the IAC valve is making the noise, install a new IAC valve.
5. Test the vehicle for normal operation.
Steering Gear Grunt/Shudder Test
1. Start and run the vehicle to operating temperature.
2. Set engine idle speed to 1200 rpm.
3. CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Rotate the steering wheel to the RH stop, then turn the steering wheel 90° back from that
position. Turn the steering wheel slowly in a 15° to 30° arc.
4. Turn the steering wheel another 90°. Turn the steering wheel slowly in a 15° to 30° arc.
5. Repeat the test with power steering fluid at different temperatures.
6. If a light grunt is heard or a low (50- 200 Hz) shudder is present, this is a normal steering system
condition.
7. If a loud grunt is heard, or a strong shudder is felt, fill and purge the power steering system.
Checking Tooth Contact Pattern and Condition of the Ring and Pinion
There are two basic types of conditions that will produce ring and pinion noise. The first type is a howl
or chuckle produced by broken, cracked, chipped, scored or forcibly damaged gear teeth and is
usually quite audible over the entire speed range. The second type of ring and pinion noise pertains to
the mesh pattern of the gear pattern. This gear noise can be recognized as it produces a cycling pitch
or whine. Ring and pinion noise tends to peak in a narrow speed range or ranges, and will tend to
remain constant in pitch.
1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Drain the axle lubricant. Refer to Section 205 - 02A for Ford 7.5 rear axles or
Section 205 - 02B for
Ford 8.8 integral axles.
3. Remove the carrier assembly or the axle housing cover depending on the axle type. Refer to Section 205 - 02A for Ford 7.5 rear axles or
Section 205 - 02B for Ford 8.8 integral axles.
4. Inspect the gear set for scoring or damage. Klj . 64 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8.
CAUTION: Correctly support the power rack and pinion steering gear to avoid
damaging the gear and hoses.
Position the power rack and steering gear out of the way. 1. Remove the nuts and bolts.
2. Position the steering gear so the front suspension lower arm front bolt can be removed.
9. Support the front suspension lower arm with a jack stand inboard of the spring seat.
10. NOTE: Note position of the front coil spring (5310) in the lower arm spring seat. It must be
installed in the same position.
Using the special tool, compress the spring until it is loose in the spring insulator (5415). 11. Remove the front suspension lower arm pivot nuts and bolts. Klj . 3 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Move the jack stand under the front suspension lower arm ball joint and raise the suspension
until the shock absorber is compressed to the previously established alignment mark (curb
height).
7. Tighten the nuts.
8. Remove the jack stand.
9. Install the power rack and pinion steering gear. Klj . 6 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

For low or spongy brake pedal concerns:
zcheck and, if necessary, refill the brake master cylinder reservoir.
z bleed the brake system and retest the brake pedal feel.
z if the brake pedal is still low or feels spongy, check the brake pedal mounting for looseness and
correct installation. Check the power brake booster and the brake master cylinder for loose
mounting. Correct as necessary and retest the system for normal operation.
For a slow or incomplete brake pedal return concern:
zinspect for binding, damage, correct installation or interference at the brake pedal.
z check the power brake booster for binding, damage and correct installation.
Vibration When Brakes are Applied
For vibration concerns when brakes are applied, perform the following procedure.
Visually inspect: ztire condition and pressure.
z suspension bushings and ball joints.
Correct as necessary. 1. Verify and isolate the concern. Brake roughness can be felt in: zthe steering wheel.
z the seat.
z the brake pedal.
2. After verifying the concern, check for related concerns in the: zOn- Line Automotive Service Information System (OASIS).
z Technical Service Bulletins.
3. Check wheel bearing end- play and correct as necessary.
4. NOTE: Begin at the front of the vehicle unless the vibration has been isolated to the rear.
Remove the tire and wheel.
5. Remove the brake caliper.
6. Measure and record the brake disc thickness. Install a new brake disc if the thickness after machining will be at or below specification. The specification is molded into the brake disc. Do z
Power brake booster
z Brake pedal linkage
z Vacuum booster hose
z Tires
z Foreign material Klj . 3 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: THE BRAKES PULL OR DRIFT booster hose as
necessary.
z Red Brake Warning
Indicator Inoperative z
Circuit.
z Bulb. z
REFER to Section 413 -
01 .
z Brake Noise zDisc brake
component. z
MACHINE or INSTALL a
new brake component as
necessary. REFER to
Section 206 - 03 or
Section 206 - 04 .
z Hydro-Boost, No
Power Assist z
Power steering
pump.
z Linkage.
z Power steering
fluid flow.
z Hydro-boost unit. z
Go To Pinpoint Test E .
z Hydro-Boost Erratic
Operation, Sticks,
Binds or Grabs z
Supply hose.
z Hydro-boost unit. z
Go To Pinpoint Test F .
z Hydro-Boost Brake
System Operation
Suspect z
Leakage.
z Hydro-boost unit. z
Go To Pinpoint Test G .
Test Step Result / Action to Take
A1 CHECK THE TIRES
NOTE:
Check tire pressure with the brakes off.
z Check tires for uneven and excessive wear and for correct
pressure.
z Are the tires OK? Yes
GO to
A2 .
No
CORRECT as necessary.
RETEST for normal
operation. A2 CHECK THE ALIGNMENT
z
Check the caster, camber and toe. Refer to Section 204 -
00 . Yes
GO to
A3 .
No
CORRECT alignment as
necessary. REFER to Section 204 - 00 . RETEST for correct
operation. Klj . 6 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...