2003 FORD MUSTANG ABS

with header.
z Convertible top
flapping with the
top up z
Vinyl top contacting
interior headliner. z
Working from front to
back, INSTALL a 6.35 mm
(0.25 in) foam sheet
between the headliner
and the vinyl top at the
suspected area. Allow a
clearance of 50 mm (2 in)
-75 mm (3 in) away from
the roof bows and the side
rails.
z Noise from roof
rack z
Roof rack rails or
crossbars loose. z
TIGHTEN the fasteners.
z Roof rack fasteners
missing. z
INSTALL the approved
fasteners.
z Roof rack crossbars
installed backward. z
REINSTALL the
crossbars.
z Roof rack rub strips
partially lifting from
roof. z
REAPPLY adhesive or
fasteners or INSTALL new
rub strips as necessary.
z Roof rack gaskets
loose or misaligned. z
REINSTALL the gasket.
z Wind noise from
bug
shield/exterior
windshield sun
visor z
Turbulence created by
location and shape. z
REMOVE per customer
direction if it is a dealer
installed option. Symptom Chart—
Brake Noise/Vibration Condition
Possible Sources Action
z Rattling noise zCaliper
mounting bolts
loose. z
CHECK the caliper bolts.
TIGHTEN to specifications.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Damaged or
worn caliper
pins or
retainers. z
CHECK the caliper pins
and retainers for lubrication
and correct fit. LUBRICATE
or INSTALL new
components as necessary.
z Missing or
damaged anti-
rattle clips or
springs. z
CHECK the brake pads for
missing clips or broken
springs. INSTALL new
components as necessary.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Loose brake
disc shield. z
TIGHTEN the brake disc
shield bolts to specification.
REFER to Section 206 - 03 .
z Clicking noise— with
brakes applied with
ABS brakes z
ABS hydraulic
control unit. z
Acceptable condition.
z Squealing noise— zDisc brake zAcceptable condition. Klj . 16 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

closing/opening
the window
z Squeak— heard
outside of vehicle
when
closing/opening
the door z
Exhaust shield
rubbing against
the chassis or
exhaust pipe. z
CHECK the exhaust system.
REPAIR as necessary. REFER
to Section 309 - 00 .
z Squeak— occurs
with initial brake
pedal application z
Disc brake pads. zUnder certain conditions,
asbestos free pads can
generate a squeak noise. This
noise is normal and does not
indicate a concern.
z Squeak— a
constant noise
that occurs with
brake pedal
applications z
Damaged or
worn disc brake
pads. z
INSPECT the pads for oil,
grease or brake fluid
contamination. CHECK for
glazed linings. A brake disc with
hard spots will also cause a
squeak type noise. REPAIR or
INSTALL new pads as
necessary. REFER to Section 206 - 03 for front disc brakes and
Section 206 - 04 for rear disc
brakes.
z Squeak— noise
occurs over
bumps or when
turning z
Worn control
arm bushings. z
INSPECT the control arm
bushings. Spray with lubricant
and CARRY OUT a "bounce
test" to determine which
bushing. REPAIR as necessary.
REFER to Section 204 - 01 .
z Worn or
damaged shock
absorber/strut. z
INSPECT the shock absorber
for damage. CARRY OUT a
"bounce test" to isolate the
noise. INSTALL a new shock
absorber/strut as necessary.
REFER to Section 204 - 01 for
the front shock absorber/strut or
Section 204 - 02 for the rear
shock absorber/strut.
z Rattle— heard
when
closing/opening
the door or
window z
Loose internal
door
mechanism,
bracket or
attachment. z
REPEAT the motion or CARRY
OUT a "tap test" to duplicate the
noise. INSPECT the door for
loose components. TIGHTEN
loose components or USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling
components.
z Rattle — GT
models only,
noise occurs from
the rear of the
vehicle z
A loose or under
torqued shock
damper
attaching nut. z
VERIFY the torque on the
shock damper- to-axle nuts is 63
Nm (46 lb- ft). VERIFY the
torque for the shock damper- to-
rail bracket nuts is 90 Nm (66
lb- ft). Do not over torque.
TIGHTEN as necessary.
z Squeak or rattle—
heard inside the
vehicle over rough
roads/bumps z
Misaligned glove
compartment
door/hinge. z
ALIGN the glove compartment
door.
z Instrument panel
trim loose or z
INSPECT the instrument panel
trim for missing or loose clips or Klj . 32 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

misaligned.
screws. REPAIR as necessary.
z Loose interior
component or
trim. z
CARRY OUT a "touch test".
ELIMINATE the noise by
pressing or pulling on interior
trim and components. USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling/squeaking
components.
z Squeak or rattle—
noise with a
vibration concern z
Damaged or
worn body
mounts. z
INSPECT the upper and lower
absorbers and washers for
damage or wear. CHECK the
body mount brackets for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary.
z Damaged or
worn sub- frame
mounts. z
INSPECT the upper and lower
absorbers for damage or wear.
CHECK the sub- frame for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary. Symptom Chart—
Steering Noise/Vibration Condition
Possible Sources Action
z Steering grunt or
shudder — occurs
when turning into
or out of a turn at
low speeds
(temperature
sensitive) z
Steering gear or power
steering hoses. z
GO to Steering Gear
Grunt/Shudder Test
component test in this
section.
z Steering System
clonk— hydraulic
knocking sound z
Air in the steering
hydraulic system. z
CHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Power steering
pump moan —
loud humming
noise occurs when
the steering wheel
is rotated to the
stop position.
Produces a 120-
600 Hz frequency
that changes with
rpm z
Power steering hose
grounded out to
chassis. z
INSPECT the power
steering hoses. REPAIR
as necessary.
z Aerated fluid. zCHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Steering gear isolators. zINSPECT the isolators
for wear or damage.
REPAIR as necessary.
z Low fluid. zCHECK the fluid level. Klj . 33 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Clunk— noise from the
front suspension, occurs
in and out of turns z
Loose front
struts or shocks. z
INSPECT for loose nuts
or bolts. TIGHTEN to
specifications. REFER to
Section 204 - 01 .
z Clunk— noise from the
rear suspension, occurs
when shifting from
reverse to drive z
Loose rear
suspension
components. z
INSPECT for loose or
damaged rear
suspension components.
REPAIR or INSTALL
new components as
necessary. REFER to
Section 204 - 02 .
z Click or pop— noise from
the front suspension.
More noticeable over
rough roads or over
bumps z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
REFER to Section 204 -
01 .
z Click or pop (FWD
vehicles)—noise occurs
when vehicle is turning z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
z Click or snap— occurs
when accelerating around
a corner z
Damaged or
worn outboard
CV joint. z
INSPECT the outboard
CV joint and boot.
REPAIR or INSTALL a
new CV joint as
necessary.
z Front suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Steering
components.
z Loose or bent
front struts or
shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn
control/radius
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test H .
z Rear suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Loose or bent
rear shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn control
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test I .
z Shudder— occurs during zRear drive axle zCHECK the axle mounts Klj . 37 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Symptom Chart—
Transmission (Manual) and Transfer Case Noise/Vibration Condition
Possible Sources Action
z Clutch rattling noise—
occurs with clutch
engaged, noise
changes/disappears
with clutch pedal
depressed z
Flywheel bolts,
clutch housing bolts
or clutch pressure
plate bolts loose. z
TIGHTEN the bolts to
specifications. CHECK
the bolts for damage.
z Clutch squeaking
noise— noise is heard
when the clutch is
operated. Vehicle
moves slowly or
creeps when the clutch
is disengaged. Can
also be difficult to shift
into first and reverse
gear z
Pilot bearing seized
or damaged. z
INSTALL a new pilot
bearing. REFER to
Section 308 - 01 .
z Clutch squeaking
noise— occurs with
clutch pedal
depressed/released z
Worn clutch pedal
shaft or bushings. z
INSPECT the clutch
pedal for wear or
damage. REPAIR as
necessary. REFER to
Section 308 - 02 .
z Clutch whirring/rattle
noise— occurs when
clutch pedal is
depressed z
Worn, damaged or
misaligned clutch
release bearing. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch grating/grinding
noise— occurs when
clutch pedal is
depressed z
Clutch pressure
plate fingers bent or
worn. z
INSPECT the clutch
pressure plate release
fingers. INSTALL a new
pressure plate as
necessary. REFER to
Section 308 - 01 .
z Contact surface of
clutch release
bearing worn or
damaged. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch chatter— a
small amount of noise
when clutch pedal is
released at initial take-
off z
Clutch engagement. zAcceptable operating
condition.
z Clutch chatter/grabs—
in some cases a
shudder is felt. Occurs
with clutch pedal
depressed/released z
Damaged or worn
powertrain/driveline
mounts. z
INSPECT the
powertrain/drivetrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 -
01A for 3.8L engines or
Section 303 - 01B for
4.6L (2V) engines.
z Binding or dragging
plunger of the clutch
master cylinder or
slave cylinder. z
CHECK the master and
slave cylinder
operation. INSPECT
the components for
damage or wear.
INSTALL a new master
or slave cylinder as
necessary. REFER to Klj . 40 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

condition. It may not always be necessary to follow a pinpoint test to its conclusion. Carry out only the
steps necessary to correct the condition. Then, test the system for normal operation. Sometimes, it is
necessary to remove various vehicle components to gain access to the component requiring testing.
Reinstall all components after verifying system operation is normal.
PINPOINT TEST A: BRAKE VIBRATION/SHUDDER
Test Step Result / Action to Take
A1 ROAD TEST THE VEHICLE—
LIGHT BRAKING z
Check that the wheel and tires are correct for the vehicle.
Inspect the tires for abnormal wear patterns.
z Road test the vehicle. Warm the brakes by slowing the vehicle
a few times from 80– 32 km/h (50 to 20 mph) using light braking
applications. At highway speeds of 89–97 km/h (55- 60 mph),
apply the brake using a light pedal force.
z Is there a vibration/shudder felt in the steering wheel, seat
or brake pedal? Yes
GO to
A4 .
No
GO to A2 .
A2 ROAD TEST THE VEHICLE—
MODERATE TO HEAVY
BRAKING z
Road test the vehicle. At highway speeds of 89–97 km/h (55- 60
mph), apply the brake using a moderate to heavy pedal force.
z Is there a vibration/shudder? Yes
For vehicles with ABS,
GO to
A3 . For vehicles
with standard brakes,
GO to A4 .
No
Vehicle is OK. VERIFY
condition with customer.
TEST the vehicle for
normal operation. A3 NORMAL ACTUATION OF THE ABS SYSTEM DIAGNOSIS
z
During moderate to heavy braking, noise from the hydraulic
control unit (HCU) and pulsation in the brake pedal can be
observed. Pedal pulsation coupled with noise during heavy
braking or on loose gravel, bumps, wet or snowy surfaces is
acceptable and indicates correct functioning of the ABS
system. Pedal pulsation or steering wheel nibble, (frequency is
proportioned to the vehicle speed) indicates a concern with a
brake or suspension component.
z Is the vibration/shudder vehicle speed sensitive? Yes
GO to
A5 .
No
The brake system is
operating correctly. A4 APPLICATION OF THE PARKING BRAKE
z
NOTE: Begin at the front of the vehicle unless the vibration or
shudder has been isolated to the rear.
z This test is not applicable to vehicles with drum- in-hat type
parking brakes. For vehicles with drum- in-hat parking brakes,
proceed to the next test. For all other vehicles, apply the
parking brake to identify if the problem is in the front or rear
brake. At highway speeds of 89–97 km/h (55- 60 mph), lightly
apply the parking brake until the vehicle slows down. Release
the parking brake immediately after the test.
z Is there a vibration/shudder? Yes
GO to
A7 .
No
GO to A5 .
A5 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in this section.
z Are the wheel bearings OK? Yes
GO to
A6 . Klj . 48 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST I: REAR SUSPENSION NOISE z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the steering system for wear or damage. Carry out a
steering linkage test. Refer Section 211 - 00 .
z Inspect the tire wear pattern. Refer to Tire Wear Patterns
chart in this section.
z Are the steering components worn or damaged? REPAIR the steering
system. INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H3 .
H3 FRONT SHOCK ABSORBER/STRUT CHECK
z
Check the front shock absorbers/strut mounts for loose
bolts or nuts.
z Check the front shock absorbers/struts for wear or damage.
Carry out a "bounce test".
z Are the front shock absorbers/struts loose or
damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new front
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
H4 .
H4 CHECK THE FRONT SPRINGS
z
Check the front spring and front spring mounts/brackets for
wear or damage.
z Are the front springs or spring mounts/brackets worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H5 .
H5 CHECK THE CONTROL ARMS/RADIUS ARMS
z
Inspect the control arm bushings for wear or damage.
z Inspect for twisted or bent control/radius arm.
z Are the control/radius arms damaged or worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H6 .
H6 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step Result / Action to Take Klj . 54 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST J: WHEEL AND TIRE I1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
I2 .
No
The suspension system is
OK. Conduct a diagnosis on
other suspect systems. I2 REAR SHOCK ABSORBER/STRUT CHECK
z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the rear shock absorber/strut mounts for loose bolts
or nuts.
z Check the rear shock absorbers/struts for damage. Carry
out a shock absorber check.
z Are the rear shock absorbers/struts loose or damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new rear
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
I3 .
I3 CHECK THE REAR SPRINGS
z
Check the rear springs and rear spring mounts/brackets for
wear or damage.
z Are the rear springs or spring mounts/brackets worn or
damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I4 .
I4 CHECK THE CONTROL ARMS/TRAILING ARMS
z
Inspect the control arm/trailing arm bushings for wear or
damage. Check for loose control arm/trailing arm bolts.
z Inspect for twisted or bent control arm/trailing arms.
z Are the control arm/trailing arms loose, damaged or
worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I5 .
I5 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step
Result / Action to Klj . 55 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...